Counting matching models…
simple insert to fit universal flush cut pliers for filament cutting etc. use with blank insert_hollow from the original HSW board Check out my collection of HSW attachments here :) Printing instructions: no supports use 4 perimeters…
CHECK OUT MY NEW RELEASE → 5015 Hot End Fan Upgrade for Ender 3 S1 (Pro) + Sprite Extruder Design: I have created this model with the following considerations: dual, symmetrical airflow under the nozzle to be as light as possible- weighs…
Protect your wipers in the winter for a minimal cost! Even 1 clip will move your wiper away if placed in the center → use more clips for longer wipers Wiper edge does rest in the empty space, so the rubber is not deformed Bottom is…
Easy to load & unload! One size fits all :) only 3.3 grams of material needed will hold even thicker 230V/110V cables, LAN cables,… designed to act as a spring when fed fully :) Printing instructions: print on its side, no brim, no…
use with blank insert_hollow from the original HSW board Check out my collection of HSW attachments here :) Printing instructions: no supports → print upright use 4 perimeters layer height pictured is 0,2mm PETG recommended Version…
use with blank insert_hollow from the original HSW board Check out my collection of HSW attachments here :) Printing instructions: no supports ANGLED version to be printed upright STRAIGHT version to be printed flat on bed use 4…
2 sizes: 10cm and 4,5cm depending on size of your curtain smooth edges and round format Printing instructions: any material any layer height 15% infill Version history: v1.0 21.6.2023 initial release
Check out also my Ultimate 5015 Part Cooling Dual Fan Duct for Ender 3 S1 (Pro) + Sprite Extruder To silence the fan even more, print my Snap-On 5015 Blower Silencer Design: I have created this model with the following considerations:…
Measured dampening is 4dB on my 5015 S1 hotend mount, measured on bed. There is very small flow restriction after mounting. See my other model for the 5015 Ender 3 S1 & Sprite Extruder part cooling duct ____________________ Printing…
use with blank insert_hollow from the original HSW board 8 slots for max size 6mm, hole diameters: 7,7,5,5,5,3,3,3mm Check out my collection of HSW attachments here :) Printing instructions: no supports, print flat on surface use 4…
angled mount will fit small and bigger thermometers, with openings from 12mm up use with blank insert_hollow from the original HSW board Check out my collection of HSW attachments here :) Printing instructions: no supports use 4…
Holds you Ikea Fixa or other tape measure :) or can be used as universal tray use with blank insert_hollow from the original HSW board internal dimensions 32mm x 70mm can be also used as universal tray Check out my collection of HSW…
DImensions: 150mm long, 25mm sides, 1mm depth internal radius 2mm Printing instructions: any material, PLA will hold just fine print orientation as shown in pics layer height max 0.28 no supports, no brim needed Installation: use glue gun…
very stiff brace for a 4040 Z axis extrusion, such as on the Ender 3 V2 and many other printers and frames position the longer side on Y legs, so that you have enough clearance for the X gantry use up to 12 screws and T-nuts you will need…
My changes: closed SD card slot, widened USB access hole for USB-C Printing instructions: PLA or PETG is OK pictured is 0,2mm layer height NO SUPPORTS needed Version history: v1.0 5.4.2024 initial release
sides are flat, to not put pressure on pages when reading angle of the helper allows to keep a decent angle of the book, without the need to overly pressure the book only 6.8 grams of material needed Printing instructions: PLA as a…
use with blank insert_hollow from the original HSW board the holder is offset by 5mm from the wall on purpose, to help clearing the wall with the finder in place. Check out my collection of HSW attachments here :) Printing instructions:…
A must have cookie cutter to enjoy your favourite racing circuit even at home :) Can be used to cut cookies, biscuits, modelling clay and for ceramic crafting. If used for cookies, please coat the cutter with some flour to help release.…
Due to tiny dimensions, the thread is self-tapped by the screw, so that the nut retains some holding power. If you need other dimensions, let me know. Height: 2.4mm ____ Version history: v1.0 29.8.2023 Initial release 29.8.2023
These tiny clips keep the Hultarp hook in place. They allow for a free swivel, but will stop the hook from being lifted. You need 2 parts per hook with total print time @ 5 minutes and 0,4g of filament. insert clip Please PRINT MULTIPLE…
Design: protects card from bending, or damaging using card is more efficient, as the edge of plastic is smooth ! sides are protruding, so that you can use the rounded edges for scraping mirrors alternatively - you can angle this…
print 1x left side and 1x right side cut any 10mm rod to length of your choice if needed, use glue to secure the rod on both ends to fit use 4pcs of 4mm self tapping countersunk screws Printing instructions: max layer height 0.2mm to keep…
If you have printed this TX_RYAN's Ender 3 S1 Twinjet 5015 Fan Duct your fan may have been badly affected by magnetism of the extruder motor - barely moving when turned on. In that case, you can print my adapter, that will move the fan to…
This model will fit Czech/Slovak Exatherm thermometers with tip diameter of 4,5mm and overall length 12,8cm. Oval body 12x9mm. Inside features a centering hole and tapered edges. The top cover is a snug fit, if your printer tolerances are…
Please note, that there are subtle variations in Ikea Lack leg width - if the tray is a bit bigger for you, you have several options: put a dab of glue gun material on the inside and let cool down 😊 rotate your Ikea Lack leg 🙃 they are…
Choose your size, alternatively rescale to suit your needs lightweight & fast to print tiny lip to keep edge smooth Printing instructions: layer height ideally 0.2mm to keep the edges as smooth as possible Version history: v1.0 06.10.2023…
Fit in place using glue gun - this will help with sound dampening Printing instructions: PETG will last longer recommended layer height max. 0,20mm print with orientation as shown in pictures, brim/supports not needed
Replacement handle for your cheap eBay/Aliexpress GoPro window sunction mount. Print instructions: use at least PETG or stronger material - PLA may become too soft after sun exposure layer height max 0,28mm 4 perimeters, 15% or more…
These are all currently available results.
