Counting matching models…
This is a custom fit strainer basket for InSinkErator garbage disposals. It has been test fitted on two different models and appears that InSinkErator uses the same size housing (slightly larger than 86mm). You can always…
Took my kids to a drive in movie and sat in the back of the truck, didn't have a place to put my drink. Saw one of these created for a 2nd Gen, but the dimensions were off compared to the 3rd Gen Tacoma. Redesigned but kept very similar.…
Remixed from http://www.thingiverse.com/thing:47982 . Increased diameter to 31.8 and added a 2mm lip at the edge for increased support for the light mount. Print Settings Rafts: No Supports: No Infill: 20% Category: Sport & Outdoors
Many older MK1, MK2, MK3, and some MK4/5 heatbeds were specified with 209x209 hole spacing. These bearing retainers have been redesigned to fit those heatbeds. Since most folks will be tearing down their older i3/bed slingers to have fun…
Many Ender 3 heatbeds were specified with 170x170mm hole spacing. These bearing retainers have been redesigned to fit those heatbeds. Since most folks will be tearing down their older i3/bed slingers to have fun and build the legacy,…
This is a bicycle fork mount for the Wuben C3 flashlight. I wanted a flashlight because they able to be used elsewhere, and I wanted one that was rechargeable along with using a USB C port.…
Bicycle fork axle mounts for a Toyota Tacoma bed rail. For fork dimensions 12x100mm with an axle lever arm less than 80mm in length. Also for standard 100 QR 5mm 110mm front skewered axle. Use with this...…
Just a big knob for the Generic Reprap 12864 LCD with a Voron Designs logo on it. Scale to fit your diameter.
I've had my thoughts on creating this for a bit. Once I upgraded the z axis rods on the Hypercube from 8mm to 12mm, I think it was time to do so. This item does a number of things: -Reduces total number of purchased parts -Reduces total…
The original bushings weren't tight enough to hold the IGUS JSM 10-12-20 bushings in place. I tightened up the diameter for a press fit application. Category: 3D Printer Parts
This is the lower locking bracket for the Ikea Rationell Spinning Corner Shelf. I have redesigned it for strength Print Settings Infill: 75%+ Category: Kitchen & Dining
This bracket allowed me to adjust the rear guide rails easier. This will align the front bed frame, squaring it up for the bed. I've also included one with a HyperCube Logo and one that is blank. Thinking @henryarnold might want to throw…
I was tired of the flex generated on the thin metal Y axis motor mount when belt tension was applied. The rear Y axis motor mount bends and this spacer/plate stops the motor from bending inward when tension is made to the shaft. Probably…
Using henryarnold's thicker walled duct, I added a center wall to for easier bridging. V1.1: Increased the center line all the way through, as it will not interfere with the fan. Category: 3D Printer Parts
Simple flat end to help with alignment of the carriage to the bed frame. For new 12mm rods. Just line it up flat, and tighten it down. I made this part, specifically to work with this... https://www.thingiverse.com/thing:4411122 Thanks,…
This is a grommet to hold the discharge tube into the metal plate of the Miele CM5100 Espresso Machine. Print Settings Rafts: Doesn't Matter Supports: No Resolution: .1 Infill: 100 Category: Kitchen & Dining
The current lever is very difficult to turn, this lever slips right over the current one and adds the leverage needed to turn on or off steam/water. *Note the lever hole is asymmetric, it is larger on one end to slide further onto the…
After 2 failed power supplies, I am considering purchasing the Meanwell NES-350-12 for the control box. I have also made the 240w version, found here: http://www.thingiverse.com/thing:2020651 You will need: This Bracket The 4 original M3…
Brush and purge bucket stand for the Voron Legacy when using a 220x220 bed. The purge bucket is set with magnets so that it's easily emptied. The brush is held down with double sided tape that unattaches easily, so the stand has holes in…
The second design I've made, but this one for the 240w version. The 350 is found here: http://www.thingiverse.com/thing:2010282 You will need: This Bracket The 4 original M3 8mm cap bolts used to affix the ugly original old power supply 4…
Purchased a used PCS-10 stand that did not have the cap at the end. Instead of a flat cap, I designed one that covers the metal and also sits flat on the ground.
These are all currently available results.
