Counting matching models…
A simple holder for an ID badge or card. Portrait orientation. Easy access to card while maintaining a secure hold. Print face up. Minimal supports needed. Enforcers painted onto underside of tabs.
My kid wanted a mini mushroom pal. I had some MX Cherry switches and figured I could combine the two. I printed with Inland Marble PLA with mostly stock settings. I added a perimeter so I could make it hollow and amplify the noise of the…
I wanted a desiccant holder that would fit inside a filament spool. I found a lot of models that used holes or vertical slots to allow air to pass through. I don't like printing posts as it takes longer to start and stop for each one. I…
II like the Prusa Printables spatula, but I didn't like reprinting the whole thing when the edge gets dull. I can also print the blade with a more durable material. There are 2 notches in the bottom at the seam to use a small screwdriver…
When you need a comb as outstanding (or outlandish) as your soup strainer. (Version 3 consists of Teeth, Bottom, and Top. I pinned it together and added a dab of superglue.) (Version 2 has a flat back and prints as one piece. You can add…
A simple card holder to hang from a lanyard. Easy access to card. No supports needed.
I wanted a desiccant holder that would fit inside a filament spool. I found a lot of models that used holes or vertical slots to allow air to pass through. I don't like printing posts as it takes longer to start and stop at for each one.…
The injection molded plastic push button on the top of my SodaStream broke in half. I made this simple replacement (V2) as a temporary fix until I could buy a replacement button. I printed it with Translucent Blue PETG so it would be…
A replacement part for a Garmin watch wrist band. The original strap that secures the loose end failed. I made this replacement with a similar peg to keep it from sliding around. It is slightly thicker than the original, but I've not…
I've tried several versions of printed clips to hold sunglasses on my car's visors. Even in more durable materials, I'm always disappointed with them after a few hot days. I wanted a clasp that didn't rely on the mechanical or thermal…
I recognize this will have a very limited audience as it is specific to one car, but all the concepts are easily transferable. I printed with PETG to withstand the temperatures inside the car and resist UV degradation. As it is a very…
Fun to make. Pretty to look at. Fails as a shape that is meant to roll. The point of a sphericon is to roll with a wobble. This only works with an even number of points in the base shape. So I had fun and I learned something. :)
I don't really mind hugging my CORE One L but it's a little awkward to reach the power switch. This allows me to toggle the switch from the side of the printer. I used Prusament PETG with a 0.8mm nozzle at 0.4mm layer height. I used the…
I have square plugs to pin the two halves together, but I found that a couple of 3/8" set screws work even better. The threads grab really well between the deposited layers and the piece holds together very well. Plus you get a very…
I purchased a garage door opener and the 2 remotes only came with 1 clip. I could buy another clip, but where's the fun in that? I printed this clip to fit over the 3mm thick side in my glove box. I used Inland Nylon to resist the heat in…
A divider to organize and store a few 3D Printer necessities. It holds a few styles of drives. There are 3 slots for the Prusa bed scraper. (or the remix I made) I keep a small lighter for smoothing that is an awkward shape. This keeps it…
The tray sits on the top bevel of the CORE One frame. There is a ledge to sit on the lip of the printers plastic window, and 2 recessed spots for a pair of 9.5mm magnets. These can be glued on or simply placed in the recesses. The tray is…
These are all currently available results.
