Counting matching models…
Recently, for some unknown reason, a lot of people have been questioning and obsessing over the idea of using stupid high CPR encoders. If you're one of those, consider this: If you do the math for 4096 CPR that is 1024ppr, that means one…
For realistic Flight Simulation, a Force Feedback Flightstick is mandatory. Unfortunately, there has been a gap in recent years due to several reasons. For some time now, the VPforce Rhino Flightstick is filling the gap. Due to the long…
If you appreciate my work and like it, you can buy me a coffee ;) but this is absolutely not expected. Short introduction: The alignment of the magnet and encoder is the most critical factor for the mechanical precision of the steering…
Hello guys, this is a Fanatec clone designed base setup for the FFBeast wheel DIY project. On the backplate i used a XT60 socket and a Type-C USB port. I have a 2080 aluminium profile version too but i need a little time to finish it.
There are two different solutions here, a geared solution and a belted solution The gear solution worked well for me originally but turns out my motor wasn't fully concentric so the gears would fail to mesh and lose encoder steps causing…
After i bought popular aliexpress bike light i needed second mount for my other bike. Its simple, yet fit its purpose. Lamp just slide in and locks with original latch. Print horizontal in PETG or even better in ABS/ASA.
Direct drive FFBEAST Enclosure. Caution!!! this is a WIP, not tested yet. this projects take inspiration in hex from EduardoGabri_2434601 For more references go to ffbeast.github.io/docs/en/wheel.html
this model used L backet for holder and more compact,economy and robust
See v1 here: https://www.printables.com/model/1282058-hoverboard-motor-encoder-and-slip-ring-mount-for-f After feedback I've updated the Fusion 360 model by adding two other versions of the magnet holder, one that screws onto a 3d printed…
This is a remix version of the 4080 base project. Before printing please make sure you check the files. :)
Feel free to modify this! Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: 3D Printing
These inserts allow the use of Preston Innovations OffBox 36 accessories with different leg profiles on your fishing seatbox or chair. The current profiles are available. - Offbox 36 insert to 19mm square - Offbox 36 insert to 20mm square…
I designed the assembly around the MT6835 encoder and a ball bearing with a 22 mm outer diameter and 8 mm inner diameter. Printing Print 56t-40mm-motor-mount in PETG, ASA, or another heat-resistant material , using supports. Print all…
Omron-like encoder holder and 8.5x gears for FFBEAST force feedback steering wheel. Do not forget to split gears at slicer for printing correctly.
CNCDan - FFBeast Wheel This project is part of my DIY Sim racing series. It uses a modified hoverboard motor to create a powerful direct drive FFB steering wheel! Link to video 1: https://youtu.be/VL34nnuZUFQ Link to video 2:…
See v2 which adds a couple different options and hopefully makes the Fusion 360 model easier to adjust with parameters here: https://www.printables.com/model/1326250-encoder-and-slip-ring-mount-for-ffbeast-wheel-v2 mount for the MT6701…
If you appreciate my work and like it, you can buy me a coffee ;) but this is absolutely not expected. Short introduction: This design is created for 6,5" hoverboard motor with magnetic encoder. At the beginning wheelbase was build around…
Wheel Using this template to drill 5 mm holes in motor case: Central hole in motor case is 14 mm. Thru hole in motor shaft is 4 mm. Hole in shaft to mount encoder is 6.5 mm. Electronics - ODESC v4.2, Encoder - MT6825. Bolts to mount…
ALL THE DETAIL ON THE GITHUB PAGE : https://github.com/p0lysim/FFB-base-differential Components used : BLDC 5065 140kv BLDC motors : https://amzn.to/3Hg6zxa MKS XDrive board : https://amzn.to/456QqmO Bearing 20x27x4 (12 pcs) :…
bottom part should be 100% or at least the motor mount part back and front are the same as the original model
Update 2: Over Christmass break I was able to button up everything. Sadly I couldn't get the encoder to work (my encoder was not working correctly, the design is not the issue), so I switched to Tig33r's magnetic encoder design. Now…
Enclouse for the FFBeast, you can print my holder for the MKS xDrive Mini, make your own plate or use a modded version of the “Original” case Require: 150mm Shaft (Put together as 100mm and have 25mm on each side) 12x M5x20 12x M5 Nuts…
EN: Here is the encoder (MT6701) mount I designed for my FFBeast project. I printed it in PETG, 6 walls, 6 base/top and 45% infill for the spacer. Tried to do a design that I could easily check the gap and test without need to disassembly…
Vespa Kunstoffbuchse für Motordeckel ---------------------------------------------------------------- Vespa plastic hinge for motor hood
Designed for a hoverboard motor conversion using the FFbeast or OpenFFboard firmware with a MKS Odrive Mini controller. This is a compact, fully 3D printed enclosure that relies entirely on printed parts, standard bolts and nuts to hold…
Inspired by viih's ffbeast mount model. My mt6701 is an i2c board 23mm on a side and didn't fit. It needed to be mounted outside of the bell with a wheel spacer that could hold a 4mm magnet. In the end, I separated the spacer from the…
Material: main part with PLA or ideally PETG lid with TPU or other flex material Don't judge my rolled cigarette in the photo, this one didn't came good :D [DONATIONS] If you find this thing good and useful, consider supporting my work by…
OpenFFBoard + ODESC / MKS Mini / Odrive-s Integrated Mount This custom-designed mount is made to securely hold your OpenFFBoard and ODESC or MKS Mini controller boards in a single, compact setup. Perfect for Sim Racing and FFB (Force…
My version for mounting the hoverboard DD wheel. Original design has SK16 blocks and the angle is adjustable. Mounting the wheel with those to my AL profile simrig wasnt good so I made a new mount. Mount has holes to connect it straight…
Disclaimer: I’m no longer working on or maintaining this project. If you're looking for a high-quality, modern direct-drive solution, I highly recommend checking out FFBeast : https://ffbeast.github.io/ DIY Force Feedback Steering Wheel…
FFB steering wheel adapter for ninebot escooter motor with viih mount.
Require: 8mm hole in shaft/24mm hole in motor 14mm Hub Spacer (Bigger, will only require new Magnet holder) MT6701 Encoder (15mm x 18mm) 4 Copper rings (10,5x13,8x0,85. 16,7x20x1,35. 22,4x26,8x1,35. 30,5x35,8x1,75) 4 Pen springs (Cut in…
50mm clearance for joysticks that would normally hit the mount (tested with FSProjects A320 Side Stick) plus the ability to adjust it lower or just use it as a spacer If you need more clearance drop a comment and I will happily upload…
Eine praktische Halterung für Ankerkraut Gewürzdosen auf einer Kastentür. Die Gläser halten sehr gut und fallen auch nicht raus wenn die Tür mit Schwung geöffnet bzw. geschlossen wird. Sehr übersichtlich, platzsparend und leicht zu…
i suggest to refer to the original page of the project to get more info but i will update the description in the future to add more info about it. Update April 27: added universal mount and added space at the top to fit m5 nut. Update May…
I needed a helmet mount for the new Offbondage led lights. Mounts to a gopro clip. 3D PRINTING SETTINGS Best in PTEG, 0.14mm, 70-100% infill.
Based on FgS36's clever snuffbox, I've added 45 degree chamfers to the drawer, the snuff chamber, the chute and the flue to allow printing without supports. Your printer must be able to handle 45 degree slopes and create small bridges. So…
still writing it
I added mounting holes for magnetic pogo-pin connectors . If you plan to use them, I recommend buying the versions with the wires already soldered, doing it yourself is difficult. If you only have the bare connectors, you can push the…
Here's the complete RC FFB controller! This is a controller I now use to play BeamNG and other games. It has a force feedback wheel, 7 buttons, a joystick, and a single trigger for throttle and brake. It should be noted that I am have the…
MKS original screws needs to be replaced for longer m3x16. Board is secured to the mount with 4 screws.
This is a simple enclosure to mount the OpenFFB TMC Motor Driver & STM32 Controller stack and provide some level of protection to circuit boards. Learn more about the OpenFFB project here: https://github.com/Ultrawipf/OpenFFBoard/wiki…
Means to create a Thrustmaster/Similar joystick extension with cheap 20mm square tube. Prints in two halves to allow addition of 5 pin mini din cable (pictured) to pass through before adding to the tube. Holes on the sides can be tapped…
Assembly of FFBeast named squirrel as it made me run to this project like a golden retriever in a park runs to catch a rodent. Complete with mockup SF90* inspired steering wheel, quick release, mounting solution for motor, MKS XDrive Mini…
My version for FFBeast direct drive wheel encoder mount. If you are using bike spoke method and AMT10E3 encoder. Encoder mount connects to sk16 block leaving 3mm gap for phase wires. Mount has 2mm hole in the middle for centering the…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 200x200mm in size You may print at higher layer heights below the Base Thickness of 0.48mm The Max allowed Thickness is 1.44mm and the Actual…
A compact enclosure for mounting the OpenFFBoard controller and TMC Driver to the MiGE 130ST-10010 motor frame.
This wall mount was designed to mount the AC Adapter for a Segway Ninebot Scooter or GoKart which use the same power interface. Not for the OEM Ninebot AC Adapter. You can purchase the AC Adapter seen in the photos using this link : 63…
I printed this snuffbox from PLA with a resolution of 0.16. In some places, you need to trim by file. The spring can be used in different lengths or so that the lid closes completely, or fixed in the closed position, but move it to the…
Insert for the OctoPlus leg system on fishing tackle boxes. Used to expand the octoplus leg system with bait trays, rod rests and anything else that uses the octagonal legs. added a v2 version with additional slots to allow it to move…
This remix contains files for using the MyActuator RMD L5005 CAN motor, 10mm panel mount switches (longer space behind the switches), a trigger to use ALPS RK09D117000C potentiometers. The handle must be mounted using a 603 bearing and M3…
Housing for a teensy 2.0 with D-Sub15 connector. Can be used to connect e.g. a Microsoft Force Feedback Sidewinder Joystick via USB. Category: Electronics
Raspberry Pi + Simhub based dash designed for the Elephoont fanatec CS DD FFBeast housing . This may also work with the official fanatec CS DD but I can't guarantee it's functionality. The design includes a safe shutdown button on the…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 150x150mm in size You may print at higher layer heights below the Min Depth of 0.48mm The Max Depth is 1.4mm and the Actual Depth is 1.5mm…
Gridfinity Aufbewahrung für Normale Paper, Paper und Tips sowie kleine ocb Tips, große Gizeh Tips und Zigaretten Paper.
Like camping in the middle of a field? Like cold beer? This mod is for you! Easily drag your cold box through a field with this off road wheels. They fold down to give ground clearance, and fold up to sit flat. Uses: 1 x Igloo Ice Cube 60…
Es soll kein Rollenhalter sein, der ein Abrollen ermöglicht. Dazu fehlen Gleit- oder Kugellager. Die Base soll die Rolle etwas erhaben halten, damit ggf. unten loses Trockenmittel rein kann. Wer das nicht mag bekommt ein Gefäß mit…
A replacement clip for a case on an offbrand dremel tool. Printed on a 0.4 nozzle with 0.08 layer height. Add supports in the spots shown in the picture.
Made these label holders because i couldn't find any suitable for cloth boxes. Used them for the below listed boxes in an Ikea Billy shelf. Dimensions of the Boxes: 24x24x24cm Dimensions of the Label: 48x20mm Width of the hanger: ~28mm…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 170x170mm in size You may print at higher layer heights below the Base Thickness of 0.48mm The Max allowed Thickness is 2.56mm and the Actual…
This is a remix of the original model focused on protecting the components and providing ventilation with a 40×40 fan.
Enclosure that uses a USB C panel mount and 2 Weipu SA20 connectors for power and encoder
Unsere insgesamt 6 Fahrradtaschen (Inhalt 20 bzw. 14,5 Liter) lagern wir in Stoffbeuteln, damit sie nicht verstauben. Um den Inhalt zu kennzeichnen, werden diese Anhänger an das Verschlussseil geclipst. Sie können bei Bedarf leicht…
BOM: -POGOPINS 6.0mm https://es.aliexpress.com/item/1005007799512492.html?spm=a2g0o.order_list.order_list_main.10.61f8194dolZVq7&gatewayAdapt=glo2esp -JST-PH 2.0 4 PINS CONECTORS F-M https://a.aliexpress.com/_EItX0KK
remix of great tiny filament sensor, for mounting on that cheap generic extruder. Somebody better than me please remix this to not mount with zip ties. 1x ECAS04 1x Microswitch without bar 1x 5mm ball bearing I carved the hole for the…
This contains 2 modified lids for using 30mm and 40mm fans. One also has a cutout for unlimited height capacitors if the original does not fit. Category: Electronics
Taller magnet holder that's compatible with my Aliexpress origin quick-release adapter (32mm tall), compatible with Viih's encoder assembly. Wheel adapter to go with the magnet holder, since there aren't too many variations for this type…
its a coffbean tank extender for the mile c5510
See v1 here: https://www.printables.com/model/1282058-hoverboard-motor-encoder-and-slip-ring-mount-for-f After feedback I've updated the Fusion 360 model by adding two other versions of the magnet holder, one that screws onto a 3d printed…
Components used : BLDC 5065 140kv BLDC motors : https://amzn.to/3Hg6zxa MKS XDrive board : https://amzn.to/456QqmO Bearing 20x27x4 (12 pcs) : https://amzn.to/46OaAmP Bearing 25x37x7 (2pcs) : https://amzn.to/3H3fCBD M3 wood screw pack :…
If you appreciate my work and like it, you can buy me a coffee ;) but this is absolutely not expected. Short introduction: The alignment of the magnet and encoder is the most critical factor for the mechanical precision of the steering…
bottom part should be 100% or at least the motor mount part back and front are the same as the original model
I added mounting holes for magnetic pogo-pin connectors . If you plan to use them, I recommend buying the versions with the wires already soldered, doing it yourself is difficult. If you only have the bare connectors, you can push the…
I designed the assembly around the MT6835 encoder and a ball bearing with a 22 mm outer diameter and 8 mm inner diameter. Printing Print 56t-40mm-motor-mount in PETG, ASA, or another heat-resistant material , using supports. Print all…
If you appreciate my work and like it, you can buy me a coffee ;) but this is absolutely not expected. Short introduction: This design is created for 6,5" hoverboard motor with magnetic encoder. At the beginning wheelbase was build around…
MKS original screws needs to be replaced for longer m3x16. Board is secured to the mount with 4 screws.
i suggest to refer to the original page of the project to get more info but i will update the description in the future to add more info about it. Update April 27: added universal mount and added space at the top to fit m5 nut. Update May…
This is a remix of the original model focused on protecting the components and providing ventilation with a 40×40 fan.
Recently, for some unknown reason, a lot of people have been questioning and obsessing over the idea of using stupid high CPR encoders. If you're one of those, consider this: If you do the math for 4096 CPR that is 1024ppr, that means one…
There are two different solutions here, a geared solution and a belted solution The gear solution worked well for me originally but turns out my motor wasn't fully concentric so the gears would fail to mesh and lose encoder steps causing…
