Counting matching models…
Mounts for Makita 18V/14.4V LXT battery and tools. Loose fit, easy to mount and unmount. Printed in PLA. Other plastics may have a different shrinkage rate, so model adjustments may be needed. Print instructions Rafts: No Supports: Yes…
I've made a kit card model of the helicopter I really like. This model can be displayed everywhere and can be great gift. Printing instructions: Layer height: ≤ 0.15 mm Infill: 100% Material: PLA (PETG might work too, but I have not tried…
Wall mount for three Snap-on 14.4v batteries. Has slots for three 60x10x3mm magnets, for mounting to a metal tool box. Also, has a 5mm hole in each corner if you wish to mount it more securely. Part should load in correct position to…
Print with Brim and 100% infill. I used carbon filled PLA. Optionally add magnets (6mm diameter, 3mm height): Standard size (¼") bit adapter: Insert the magnet after print. There is a press fit slot inside. Push hard to get it in. Mini…
The enclosure consists of 2 parts: Top and Bottom. The XH-M609 board is placed first on the bottom case, to ensure centering, then the top part is seated over until there is no gap on the sides. The assembly is secured with 4 M3x12…
Remix from existing designs, i would like a hub generator to enable everyone to do it own. Hubs works with 1V, 2V, 3V, 4V, 5V, 6V geodesic dome Strut profile : rectangle or round use Dromerama calculator to get Strut sizes :…
My Littelest Great Grand-Daughter borrowed one for her kitchen and didnt return it, so i decided to try and design one. I came up with two versions. One is Bigger & more Rugged The Other is slightly smaller and fits better than the…
NOTE: as requested in comments (in Russian!) as of Sept. 21, 2025, this listing now includes a remix that covers up the ventilation hole while also provided a mount for the buck converter. For adding LED lighting to the non-pro version of…
Update 03/24: While the original Version still holds up extremely well, I wanted to increase stability for the Front Wheels because there is quite some load on the original Wheel center rings. Those rings that come with the Kart are made…
This is just a simple wall or tray mount for your Flex 24V batteries. The .f3d file is messy, and not really intended to be edited or terribly useful to remix, but the file itself works well. I've printed in a few different PLA's, and…
This is the first iteration of a Kobalt 24v battery wall mount; it can be mounted anywhere, because it has the locking cutout made in it as it does on the tools themselves. There are also some easy-out mounts (ones that do not have the…
This is a remake of my 70 mm PSU cover for the CHENGLIANG P360W24V used in the Sovol SV06 (https://www.printables.com/de/model/341847-sovol-sv06-psu-case-cover-for-silent-70-mm-fan-and). By using a 92 mm fan, the fan speed can be further…
Simple wall mount for the Unifi 60W power brick delivered with the Unifi Cloud Gateway Fiber. Works best in PLA due to it's rigidity, requires supports (tree is best) for the clips. Uses 2 3.5mm countersunk screws to fix it to the wall.…
You can buy these diffusers from me here! If you like our models, consider giving us a 1 time donation! Please see the assembly instructions photo! This is a flashlight diffuser that distributes the light radially and downward to maximize…
I wanted to use a 14.4V Makita battery to power one of my projects so i made a battery mount for it, i used some thin metal sheet for the contacts, maybe for higher currents i should change it for a thicker steel or copper one. i took…
This slow bean feeder provides consistent, controlled feeding of coffee beans into DF64 or DF64V grinders. Features: Variable Speed via potentiometer USB Powered (5V) with optional LiPo battery support Direction Reverse with push button…
Cover for the Tobsun 12V or 24V to 5V converter found in the Voron 0 BOM. Is also usable for powering a Raspberry Pi on most 3D printers.
TOBSUN DC-DC 24V/12V to 5V converter din rail mount Based on the VoronUsers 2 channel relay mount and I also added the unmodified Voron 2 DIN rail clip for your convenience. This fits the DC-DC converters which are e.g. part of the Voron…
The cutout in the aluminum extrusion for the cables on the Elegoo Neptune 2S is a bit sharp on my printer and could cut into the wires if moving the printer around and modding. This cover snaps into the cutout and protects the wires.…
First, the original I modified is a very beautiful structure. Please check it out. I've bought battery backup bulbs before and when the power went out, they were not very bright. I made this for any power outage and with several batteries…
This is a BTT UPS 24V Mount for my DIN Rail Bracket. You can find the bracket here ! For the UPS you need M3 flat head screws and M3 Nuts. For the DIN Rail Bracket Mount you need M3 countersunk screws. Due to the heavy load on the SSR and…
This is for the first version of the T114, the one with problems. I haven't received my v2 yet to see how they compare physically. ------------------------- This is a pretty accurate version of the Heltec T114 plus screen. One side of the…
O-ring failed on my portable 24v inflator and i found the problem to be a bad seal on the pump. Its a tight fit but work. Use as many perimeters as you can and .16 layer height.
This is a little something I whipped up to hang my 24v Kobalt tools from the underside of a bench, or in my case some cabinets. Print Settings Rafts: No Supports: No Resolution: .2 Infill: 25% Notes: Designed to print standing upright…
This is a 4-piece holder for the Ryobi USB 4V batteries that works with the Honeycomb Storage Wall (HSW). There are several options: Plug insert vs full insert: Allows you to attach it to the HSW in the method you prefer. The Full Insert…
RYOBI has come out with a new USB Lithium 4V Battery system. The battery is charged via a USB type C port. So you can Solar Charge it! They only have come out with a Cutter, Screw driver, Chisel, and Rotary Tool. I designed and 3D printed…
BEEFY DIN RAIL MOUNTS These are Completely Overbuilt! They Require 1 purchased part - Link Below I made these mounts to solve the below issues from the Voron 2.4 r1. BOM STL files Will work on any 35mm Din Rail Mounted Setup These are…
You are doing me a big favor by clicking the Like button :-) Print with 100% infill. Glue round magnet 6 x 2 mm in the bitholder.
I'm working with 12V and 24V vehicles where I have to test single components. because I have a 12V Milwaukee M12 battery powered drill. I designed this handy power supply. Both parts can be printed without supports. Additional hardware:…
I wanted LED lighting on my X1C but didn't want another plug. By powering off of the AMS I can use a single smart outlet for the whole thing. Works great! Use this box to bundle wires behind your printer and power lights directly from the…
The Ryobi 4V USB Lithium belt clip replaces the battery cap on Roybi 4V Lithium tools. Simple to install, just replace the battery cap on most Ryobi 4V USB Lithium tools. Tested with the Screwdriver, Power Cutter, and Magnifying Light.…
The new Ryobi 4v USB Lithium tools storage systems are limited, I was able to combine two creators solutions and make a single pegboard style mount system. For the rail system you can either print a 2 post rail or a 4 post rail, depending…
My personal issue with my XL printer started a few weeks ago. This is my first summer with my XL and I am finding out that my garage is just too hot for the XL to work. When the temp gets up to 90ish, the printer has one of the sensors…
Custom Designed Wind Turbine - Version 1.1 12-24V The following description will help you understand the plans for my custom-designed wind turbine. The project is based on a hoverboard motor, which serves as the generator. Most of the…
This is a case cover for the CHENGLIANG P360W24V power supply from Sovol SV06, with a hole for a 70x70x10 mm fan and a step-down converter (LM2596 HW-411). There are holes for fusible nuts (M3 with 4.6 mm outer diameter). Unlike the…
Designed to work with most 4V USB tools and Tek4 tools, but likely not all.
I have old BOSCH devices that need the old 14.4 V NiMH Battery Packs from BOSCH (Form O, 2607335850). I designed this adapter such that you can use the standard BOSCH proferssional slide-on batteries (GBA-18V) instead. Note that BOSCH…
LowRider v4 CNC - Tie Downs to secure 24v Power Supply (AC-DC) to lower strut plate of gantry. This is the 24v power supply I purchased from Ryan at v1e.com … Print as oriented. No supported needed. I pre-drilled and used M3 screws, but…
After I made the 70 mm and 92 mm Version of the PSU fan case, I got a request for a 80 mm variant from PatrickE which is exactly this one. I did not test it myself, but PatrickE confirmed that it fits and also provided the pictures, thank…
I'm working on a short nozzle for the Kobalt 24V blower (Model #KHB 4224A-03) to use while drying cars. I needed something quickly, so I just designed an attachment that attaches to the tip with an interference fit. The current iteration…
A case/extrusion mount for LM2596S 24v+Coax to 5v+USB buck converter.
Schutzkappe für einen Makita Akku 14,4V oder 18V Supports sind in der Konstruktion integriert. Nur noch heraustrennen und entgraten. Protective cap for a Makita battery 14.4V or 18V Supports are integrated in the construction. Just cut…
A case for the HCW-P715 USB 5V/5A converter wich can be used to power the Raspberry Pi or Creality Wifi-box directly from the printer power supply. Made to be mounted on the 40x40 Aluminium profiles with 3mm T-nuts. One version with a…
An enclosure for a JZK HW-688 Buck Converter (24V/12V to 5V 5A USB) Designed to mount on the 4040 profile of an Ender 3 directly underneath the Enders power supply for easy wiring but can also be mounted at the front of the printer next…
Delta PMZ-24v240WDAL PSU for the Prusa i3 MK3s+ (The black version) You can use this STEP model as a base start for any modification/upgrade.
This simple battery holder was designed with the intention of mounting under a cabinet with two #6 flat head screws. Its intended to fit FLEX Power Tools branded 24V batteries. Printed standing up on it's end, it will use minimal support…
Now you can arrange your Festool batteries as you want it. This holder fits perfectly to the original 14.4V/18V batteries and has 6 mounting holes for M4 screws to fix it on an 20x40mm aluminium profile in different heights, against the…
This is a wall mounting plate adapter that I've made due replacement of my old Speedport W724V. It was mounted on the wall by two screws. For the new Fritz!Box 7590 I didn't want to drill new holes, so I decided to make an adapter plate…
Print this bottom to allow integration of a kobalt 24V battery to the 18V ryobi tool. Use the top part from the linked model for the RYOBI half. For terminals on the kobalt half Use spade terminals or appropriate ring terminals and…
Case for HiLetgo 24V/12V to 5V/5A Power Module DC-DC Step-Down Power Supply Converter Case Link: https://www.amazon.es/dp/B07X5H4M42?ref=ppx_yo2ov_dt_b_fed_asin_title Printed with support. 2 cases were made since one of the PCB had a…
Mount your Ryobi Lithium Screwdriver 4v HP54L (and HP34LVN) on a Skadis pegboard, combined two models I found so it works with Skadis: Universal Skadis Mount https://www.printables.com/model/282336-skadis-universal-mount-big 4V Li-Ion…
Designed to work with a variety of 18V Ryobi tools and batteries. Most items shown printed in Overture Grass Green and Black PETG.
This wall bracket is suitable for Makita batteries 14V and 18 V. Print instructions It is very easy to print. I always use PETG and print with supports. But I think that PLA would be the same. On my Prusa i3 mk3s, I always print with 20%…
I Simplified the design from 3 pieces to 2 pieces and made it better fit the USB terminals.
Many cheap printers are using the Cheng Liang P360V24W power supply. The biggest flaw of that model is the loud fan inside the PSU. There are a few cover mods on Printables, but they all just work when the PSU facing out of the printer.…
Wall mount for Bosch 12V (10.4V) Charger, also (supposedly) supplied with some Dremel models. Its definitely compatible with the Dremel batteries, I use it myself. My charger model number is GAL 12V-20. There are other mounts out there,…
Battery mount for the Flex 24v batteries printed standing up with tree supports for the small overhang
To make it waterproof. I recommend to add silicone (as example Done Deal) on all adjacent surfaces, and to the wires under the small cap. Use it on your own risk! PS: parts are very stiff to connect. Its important for better waterproof…
You are doing me a big favor by clicking the Like button :-) Standard for parkside cordless 4 volt screwdriver
I wanted a basic cover to put over my batteries when not in use as I do not like to store them in the tool. Made in openscad. Tried to over engineer it and ended up going back to some basics. This should fit the battery snugly, but not be…
Transform your Emisar D4v2 flashlight into a fancy lantern! Do you like the BLF LT1 and want something smaller? This might be just right for you! Included in this kit are two parts (consisting of three models to print): The base for a…
You can buy these from me here! Consider giving us a 1 time donation if you like this model! I have uploaded the raw .STL files, and I have also uploaded my .3mf files. The raw .STL files do not have the holes for the light made in them,…
This a holder for you Kobalt electric screwdriver and bits, I have included two options a 1x5x5 unit and a 2x5x5 unit. The smaller of the two is what I have made and have pictures showing, as the mini toolbox doesn't have a lot of room,…
Habe keine Halterung für die linke Seite eines Ikea Lack Tisches gefunden. Habe selber eine erstellt. Viel Spaß beim drucken! Print instructions Habe es mit 0,2mm Layer high gedruckt. Ohne Support.
Not much to say really, I just want to have my tools in an easy to reach place so I hotglued it to the side of my 19" rack case. There are also 2 holes for screws built-in but I didn't need them. The screwdrivers bits click in place. You…
I changed the original file from joloman2 to have a fan guard and a base for the fan in order to screw it in the right direction without the trouble of the fins hitting the fan guard. I used a Noctua NF-R8 redux-1800 and i honestly cant…
Overview: This is a power supply cover/enclosure to contain he wiring, electronics, and input/output connectors for a 24V AC to DC power supply. It allows me to safely convert electricity from the wall (230v) to 24v DC power for all of my…
This is a remix of felixna's model with an added slot for the fan's cable as suggested by Thomas Albrecht in the comments of the original model. The notch is measured from a Noctua Redux fan, but it should be very similar for most fans.…
Just a basic box to enclose and mount the BTT UPS 24V v1.0, knowing me I have probably over engineered this ;) To secure the base part to extrusion use 2x M3x8mm machine screws with 2x M3 T nuts, maybe a thin washer too. Fit the UPS to…
Greetings Everyone! Like many of you, I printed myself a Bento Box filter to keep VOCs from entering my lungs. The only thing I wasn't sure about was how to power the fans. So with that in mind, I decided to learn enough CAD to create my…
I changed my PSU for a 24v 15a one and I designed this cover. I am using the following PSU: https://www.amazon.com/gp/product/B0146IAXYO/ref=ppx\_yo\_dt\_b\_asin\_title\_o08\_s00?ie=UTF8&psc=1 Regarding the socket, I don´t have a link but…
This is designed to be mounted to the underside of a flat surface (eg. a table, a shelf, etc.) using screws. The holes are sized for #10 screws.
I was unable to find a base plate that would work with my Kobalt 24V Trim Router, so I decided to model the one that came with it. I plan to design additional attachments following the bolt pattern for this router. The eventual goal is to…
I wanted a under shelf mount for my Cordless Screwdriver (harbor freight 64313 https://www.harborfreight.com/4v-lithium-ion-14-in-cordless-screwdriver-kit-64313.html ) So I took a profile pic of the screwdriver on graph paper, traced it…
Wrist rest / Palm rest for Keychron k4v2. Prints in 2 parts so it can fit on non massive printers (each piece is 192mm long Orientation : would recommend either printing upside down or standing up on its end depending on the texture you…
Works with Bambu Lab X1, X1C, and P1P printers. Uses two (2) Bambu Bus Cables. Items Needed to Construct the BL LED with 24v Power Tap: BL LED for sale at dutchdeveloper (Etsy Store) Power Tap Kit and extra Bambu Bus Cable for sale at…
This is a compact DC power supply that is powered with AC power. Wanted a lower power and adjustable compact supply to use on my desktop with spring terminals to quickly use with bare wire. No more searching for wall warts of the right…
This is a case for the Walmart's Hyper Tough 4 Volts 45-Piece Rechargeable Precision Screwdriver Set, Model 30009 The v2 has a slot to allow charging while the screwdriver is in the case Here is the link to the model designed in on shape…
Thing to make the Ubiquiti POE-54V-80W Din Rail mountable. Works best in PETG or PC. You will need a Din Rail clip, either from the jungle site or make one yourself (model can be found on my profile). Note that it is a very tight fit.
Designed after kids stripped out the factory gear. I used PLA to test and it worked until it didn't while waiting for warranty replacement. Printed with 5 walls and 30% gyroid infill. .15 layer height.
Just another PSU fan cover for E3PRO Meanwell LRS 350 24V. I did not like any model so I made this one from scratch with some Witcher features, but uploaded “classic” version for not Witcher fans. Use supports. Tested with 92x25mm Noctua…
DC powered electric sander / polisher based on RS-555SH 36mm 12V 24V High Torque DC Motor. Attachments are easily exchangeable when sandpaper of different grids is required. Just print a few sets of them and equip each with different…
You can buy these from me here! This Skilhunt HB3 headband works great with the mount. This rotating 3D-printed mount allows you to easily attach and remove your Emisar D4V2 or D1V2 to a headlamp headband. This bracket can be attached…
I loose my stand for my TV.. so here it is
It is fully printable without supports positioned as it is on the buildplate, however I found the strength and plasticity of the holders in the middle weak and fragile. So I recommend printing it vertically like the one in the pictures.…
Mount for DC 9V 12V 24V to DC 5V 5A Buck Converter
Overview Designed with precision and robustness in mind, this protective case is specifically tailored for the BTF-Lighting A24V10A PSU and controller. Its hefty structure, with 1cm thick walls, ensures unparalleled protection for your…
USB modul https://www.aliexpress.com/item/1005007439875485.html?spm=a2g0o.cart.0.0.457738da0Q5hBN&mp=1
BOM: 1no. HP DPS-800GB Server Power Supply. (12V output) 1no. DC GND Isolated HP DPS-800GB Server Power Supply. (12V output) 8nos. 213mm x 12.8mm width x 2mm thk. Alum. bar. (support bar model.pdf) 16nos. m3 x 6 screw. 1no. DC 50A LCD…
Carcasa reversible (la misma pieza hace de tapa), impresa en PLA+.
Support Ryobi (batterie 4V, visserie....) Imprimer sans support
Yet another Ender 3 Pro fan cover, based on a 90mm fan and i use inserts M3 for mounting the fan internally. Use supports for overhanging part.
Remixed existing design and scaled.
purpose We developed this charging station to offer free phone charing for people on the public square next to our maker space. Two large smart phones can be charged simultaneously laying on the top front. Providing QC3.0 and PD even…
I used PETG, so the heat of the DC motor doesn't deform the print. PLA could still work; obviously, don't let the motor get too hot. Printing is easy and supports come out quickly. Required: Print at a 0.2 Layer Height Print with 30%…
I have designed a case for a standard SMPS 24V 20 A to be used for a LiPo charger . It is in two parts each part secured by screws in the SMPS . There is plenty space for venting and cooling in the case
This is a 92mm fan mod for the common Cheng Liang P360W24V power supply. The assembly requires you to have the following items: 4x M4x30 or M4x40 (with spacer) flat head machine bolts 4x M4 washer 4X M4 nut 92mm fan optional mesh for 92mm…
A while ago I made a holder for 2 of the Ryobi 4v batteries, Rotary Tool and Driver . It worked well, and has a few makes, but I was never very happy with the aesthetics. So I set about making holders for the batteries and each of the…
Habe für meine 4V Tools von Ryobi ein paar Halter gebastelt
This is a carrier for 2 Kobalt 24v batteries. This requires the use of these locking holders. It requires 4x M4 heated inserts and 4x M4 button head bolts. This version requires support for the handle. .step file included for modification.
