86 models
I created this simple and (almost) fully printed anemometer for students in local high-school programming classes. 3D printed parts (PETG): Top dome Top core (this is where a small magnet is placed) Bottom body (this part contains a Hall…
Overview on project This is part of the Weather Station One project, a complete and modular weather station. The design of the system has been driven by a number of requirements: collect all common weather channels including temperature,…
Wind indicator, without additional bearings. Printed from PLA. After printing the bearings gently hold and move them, then add some oil. The blades for the windmill should be printed with supports. Bearings should be printed at a height…
Funnel that mounts on the Uni-T UT363S To measure the airflow of a household ventilation system you can use an anemometer with a funnel that fits around the vent-opening. (up to 185 mm) Then calculate the flow with the surface area of the…
This is a model of the anemometer with wind speed and direction measurements. The whole can be mounted to a 40 mm pole. Electronics inside contains 3 PCBs: AS5048 demo board from Austria Microsystems in a set with round directional magnet…
All the hardware i will be using is necessary for the stock version. Though you can modify the parameters to fit your screws and bearings. I opted to use bearings since it makes the whole assembly pretty much silent. It is also very…
Be kind this is my first post :) A print the scale 1 Category: Outdoor & Garden
This model consists of the two anemometers, the antenna and the antenna platform for the Apollo Launcher / Umbilical Tower used to launch the Saturn V rocket. This is part of the Apollo Umbilical Tower model. See the parts spreadsheet of…
This project contains ballbeaings, runs very smoothly, no need to purchase extra ballbearings. Quantity to print： Ball * 20, Cup * 4, Direction_indicator * 1, Inner_ballbearing1 * 2, Inner_ballbearing2 * 2, Main_rotor * 1, Pole * 1,…
needed : 2 X M3 20 mm Socket Head Cap Screw Bolts, with nuts 1 X 6700RS bearing [10 x 15 x 4 mm]
Da bei meiner Homematic-Wetterstation ein Löffel vom Windmesser abgebrochen ist (gemäss meinen Kindern, hat der Ball diesen beinahe nicht berührt :-) ), habe ich eine neue Nabe und Windlöffel gezeichnet. Die Form und die Idee für die…
Anemometer V1 for Arduino Anemometer V2 is available here: v2 printable Material: 3 x 4x2mm Neodymium magnet A3144 hall effect sensor 10K resistor Arduino Nano It uses 3 magnets that are inserted/glued inside the head in the hole (I had…
Anemometer used for the automatization of the garden sliding shade. Basically, print 3 cups, then print the cover, insert the cups into the openings within the cover and apply the thin CA glue to fix it. Print the tower and insert the…
Anemometer made for an M8 bearing to minimise friction, the bearing fits inside the support.stl file. Note a modified version can now be found at http://www.thingiverse.com/thing:338464 The centre goes through and rests on top of the…
Anemometer with wind direction indicator. User Creation Mix: neovista85 - Thingverse I modified the original project to insert bearings and make some mechanical and aesthetic improvements. Known issues: -The fitting of the wind spheres…
The Best part of V3.. NO SUPPORT NEEDED and is much stronger !!!!! It can handle even slower wind speeds without stalling. I've recorded as low as .5 mph and up to at least 65mph+.. This V3 version is a total re-make not re-mix of…
Anemometer V2 for Arduino Anemometer V1 available here: v1 printable New Features: Lighter - easier to spin, less mass - less momentum. Integrate only one imbedded magnet. Lower center of gravity - more stable. Material: 1 x 10x1.8mm…
Anemometer for wall mounting. Instructions Inspired by the other anemometers on thingiverse. Easy to make - requires 1 x 8mm bearing - the pictured version was printed using the Replicator 2. Print the following: Anemometer Cup x 3 -…
Hardware you need: 5 M5 X 30 mm bolts 1X skate roller bearing (608 size) Anemometer cups: glued to the rotor arms. Better to be printed upside down using supports. Remove the skirt and all pieces can be printed in one shot on the prusa…
Anemometer Cup and what I call the center dome for the home weather station. The center dome holds the bearing and magnet for triggering the reed switch for measuring wind speed. (Mine is an old Lacrosse Technology from more than ten…
The python code for the project is published here: jattie-ire/anemometer: 3D printed anemometer with a raspberry pi data logger (github.com) I designed this in order to find the best place in my garden to mount my vertical wind turbine,…
With this small model of a anemometer you can observe the wind speed or count the revolutions of the cups in a minute. It is also a nice model for experiments or explanations or you can check if it is windy outside, The axis, connector…
Here is a simple designs anemometer. It's small anemometer with bowl diameter 3,5 cm, and the diameter of assembled anemometer is about 15 cm. I made three variations of Cup with different roundings. The model is made for bearing 608. You…
print with supports if using outside dont use PLA ( mine are petg) prusa mk4s ive provided f3d file so you can change connection method or your can make a pole to suit my mounting method 0.4mm nozzle should slide in tightly
Print files and Fusion 360 project to make a weather station. It will need an ESP8266 pro to log stuff. The pro is required as it has an external antenna. It all clamps to a 25mm aluminium pole. The raingauge is a tipping bucket type - it…
I broke the cups off of my anemometer when I dropped the unit during a battery change. This replacement glues onto the centre hub of the old anemometer. I printed mine in white PLA, and gave it a few coats of a clear UV protectant spray.
This project contains ballbeaings, runs very smoothly, no need to purchase extra ballbearings, no extra parts need to be purchased, and minimum support is required. Quantity to print： ball * 20, blade * 3, blade base * 1, head * 1,…
Hardware you need: 22 M5 X 20 mm bolts 2 Skate roller bearing (608 size) 2 bars 15 mm diameter. Minimum length 300 mm. Support is designed for a 35 mm diameter pole. Anemometer cups: glued to the rotor arms. Better to be printed upside…
This anemometer is calibrated out of the box, robust, easily be printed and needs only little hardware to get it ready. It is intended to be used with a KY-024 hall sensor as pick up. Easily be implemented with Arduino, ESP32 or RasPi…
This can be used with the Uni-T 363S meter, add an M6 screw to attach the funnel to the device. Printing: enable supports, print with the wide side down. Printing parameters are non-critical.
The anemometer (wind-speed detector) on my WS-1200 was destroyed in a hailstorm. The rest of the weather station was completely undamaged, so I didn't want to just trash it. This is my replacement part. I don't have them to compare with,…
Adapter for TESTO anemometer 410-1 // 410-2 with platform for screws… AD2) model for PET bottle 5L cap ONSHAPE designed
An anemometer is a device used to measure the speed and direction of the wind. There are several different types of anemometers, but the most commonly used is the cup anemometer, which consists of three or more small cups mounted on cross…
Modified the original Anemometer cup design by PlasticyBits for the TX20 La Crosse Weather Station. Had to lower the cuts to clear the housing, and angled the ends for a better fit in the dome. . Also had to move the magnet slightly,…
OBJETO PARA CAPTAR O VENTO, SERVE COMO PARTE DE UM DISPOSITIVO PARA MEDIR O VENTO
This is mechanical part of anemometer. Provided OpenSCAD source requires BOSL library. Then you need Arduino and ESP to signal conditioning, counting and sending measure over wifi.
This is part of the weather station which is itself one device into the Rezodo project! Full description can be found here (don't hesitate to follow and like this open source open hardware project please!)…
This model doesn't plan for electronic parts but is meant as a simple yet nice decoration for your bike. It will spin following the wind and your speed, serving as a fun eye-catcher to passer-bys. It requires a 608(zz) bearing and the…
This is a protective hard case for the Testo 405i anemometer (measures air velocity). It is a hot-wire anemometer so it is very delicate, and it did not come with a case, so I designed one for it in two parts - a case and a lid. The lid…
This guard prevents birds from resting on the gauge, thus, keeping it clean. I've printed this with 100% infill in order to give the spires strength, however, they are still rather delicate.
Hélices de l'anémomètre du store Dooya DM45RM-50/12, qui avaient cassé chez moi. J'ai découvert Fusion hier soir et c'est mon premier modèle, donc il peut obligatoirement être amélioré, mais il marche parfaitement ! J'en ai profité pour…
Introduction When you change something in your mechanical ventilation system, it’s a good idea to double-check that all vents still deliver enough airflow for a healthy indoor climate. Pro measuring tools are pricey, and the DIY versions…
This 3D model of a cup anemometer (a device used to measure wind speed) was created as a case study to demonstrate a robust and reproducible design workflow . The primary purpose of sharing this model is educational: it provides a…
Netatmo Anemometer Bracket Here's a bracket to mount the Netatmo Anemometer on a pole. The bracket is split in two, left and right and there is an STL file here for each one. Two pole sizes are provided 20m and 25mm. The fixings needed…
Anemometer replacement for Auriol H13726 weather station. Must use SLA printing Friction fits due to not having enough time to design a screw mount. Might need to hand shave the hole using a drill bit.
Funnel and flow hood to convert a PM6252A digital anemometer into a ventilation calibration device. Adapter can be taken apart for storage.
This anemometer is intended to be used with an android phone. It is mounted on its base via a balls bearing. It's a 11x7x3 mm bearing extracted from the heads coil of an old HDD disk. Consequently it's a high quality bearing with a very…
Printed in PLA. No support needed. I fixed it with Blu Tack. Made for Netatmo Anemometer (GTIN 03700730500227).
The holes are sized for six 3mm dowel pins. The sample shown was printed on a Lottmax Shark V3 printer (love this printer) at 0.15 resolution and 30% infill after being sliced in Cura. After building a mechanical prototype I've decided to…
I created new model from the scratch, but I was inspired by the original version. Protrusion tabs are more strong and it has better fit to my anenometer. Printed with PETG, but PLA will work as well. 0.2mm, without supports.
Internal diameter of slope should be 45mm or so. I've made a hole for the hot melt inset nut (M4) just to keep it in place. I recommend to use the PETG filament, 4 perimeters and 40% infill.
Anemometer for a raspberry pi.Use either a Hall effect or Reed Switch hot glued to the side via the opening the body. Hot glue a neodymium magnet onto the threaded rod. Requires: 2 x 608z bearings 5 x M8 nuts 3 x washers Threaded Rod The…
Sphere anemometers are simple devices that use the wind drag force on a sphere to determine the wind speed by equating the weight of the sphere with the drag force in a pendulum like configuration. Modern versions of this device use…
A friend was facing replacing a whole Navico Wind Direction and Speed system on his 30 year old sailboat because he was unable to find a replacement wind cup. So I reverse engineered the hub, cap, and cups for the Navico System 200 WD200.…
Didn't have the bearings required, so just modified the two parts
The anemometer has no surface to stand on, so I designed a holder to put it in. it can also be mounted on a tripod, if you get one of those adapter screws( amazon link ) and put it in from the inside. I used a heatgun to soften the…
This is a simple pegboard mount for my handheld digital anemometer. This model is sold under multiple brands and is available for about $16 on Amazon . The model is designed parametrically in Fusion 360, so you can make a similar but…
Inner diameter of bearing is 28mm. Insert the rollers into the bearing ring and tighten the 30mm screws and insert the m4 nuts with the longer screwsInsert the rollers into the bearing ring and tighten the 30mm screws and insert the m4…
Nachdem der Netatmo Windmesser nur mit einer ¼ Zoll Schraube befestigt werden kann habe ich nach einer Möglichkeit gesucht um diesen auch auf Oberflächen befestigen zu können. Ich habe mir hierzu diese ¼ Zoll Schrauben von Amazon bestellt…
To mesure wind speed using an arduino and a photo sencer Category: Outdoor & Garden
A simple model that makes 52mm hemispherical cups with a boss to attach to a rod.
I picked up this anemometer from Adafruit: https://www.adafruit.com/product/1733 I plan on using a magmount adapter with a 1/4-20 screw to mount it. The anemometer base has four screw holes, so I made an adapter. The hole for the 1/4-20…
I thought this would be a funny print, I don't have the cooler myself to test it out, here is hoping I win one XD
Arduino anemometer using WH-SP-WS01 sensor and LCD 16x2 keypad shield. Powered by 9V battery.
Spare wind cups and hub assembly for the anemometer of the TFA Sinus/Nexus weather station. Suggestion for printing: print on PETG.
This sub-model consists of the lights and anemometer parts for the LUT Cross Section model.
A coworker broke this at home, so, since I'm learning openscad, I took the challenge to design it from scratch and print it :) P.S.: bear with me for the ugly code =_) Print Settings Printer Brand: Creality Printer: Ender 5 **Rafts:** No…
I've designed this fan for a friend, printed in Pla with my ender 3 printer. Sliced with Prusa slicer 2.9.0. 100% fill, supports needed. Shaft hole ø4 mm.
This is a corner mount for the Netatmo anemometer. You can use this if you cant easily access your rooftop or have no way of mounting it there. While mounting it directly next to a wall isn't optimal either this should work fairly well.…
Spare wind vane assembly for the anemometer of the TFA Sinus/Nexus weather station. Suggestion for printing: print on PETG.
This is the top assembly of an anemometer, designed as a replacement for the unit on my awnings. I modeled it to closely match the original, but I made the cup walls slightly thicker for added durability when printing in PETG. The…
With this adapter it is possible to attach a funnel to the WS4003 anemometer. I have designed this funnel adapter to measure my air conditioning system at home. The adapter can be printed easily without support and with snappers not…
Blade for anemometer with removable blades.
Design Concept This bicycle anemometer model measures wind speed in a simple and intuitive way, featuring brightly colored wind cups that attract attention. The model uses contrasting red and yellow colors to enhance visibility and…
Made in 2 parts to be glued together. Small ears are to help part alignment while gluing. Cut them at the end. Printed in white ASA.
Anemometer Adapter 140mm x 140mm Settings: 0.2mm layer 2 walls 15% infill No supports Filament: AURAPOL PLA-HT (you can use whatever you want)
The bearing I used is not 100% sealed so I made this cover as a bit of a protection from the elements.
Funnel for not expensive anemometer HoldPeak HP-5000D. It can be used to measure air speed/volume on up to 200mm diameter pipes. I've used it to check my HVAC (recuperation) at house. There are other funnels, sadly each of them (also this…
Spare wind cups and hub assembly for the anemometer of the TFA Sinus/Nexus weather station. Suggestion for printing: print on PETG.
Spare wind vane assembly for the anemometer of the TFA Sinus/Nexus weather station. Suggestion for printing: print on PETG.
Discover the latest “mini” version of the 3D-printable anemometer "Anemosens," designed for precise wind measurements and size requirements. The mini version of the Anemosens features optimized ball bearing sealing for even more reliable…
