Counting matching models…
rollbar and flatbed for the ascent use the shocktower mounts to secure the bed, rollbar screws in the bed with 3 2.5x10 (reused screws from the ascent) supports screw in the rollbar with 2 2.5x10 (also reused screws)
Inspiration taken from this CSGO planter: https://www.printables.com/model/58274-counter-strike-mirage-planter-turntable it's not 1:1 scale but its close enough. I noticed a bunch of floating stuff in the pictures and fixed the model.…
Small storage to stow away keys, spare fuses, cash or other small items. The printed part attaches securely to the driver side Fuse panel lid part# 66135AJ020. Subaru uses the same fuse lid part# 66135AJ020 on its various other models…
low profile shock tower redcat ascent
Description 2023-2024 Subaru Ascents have 19 cupholders. All of them are too small for my 40oz Thermoflask container as well as most soda fountain cups here in the United States. The cupholders between the driver and passenger seats have…
flatbed for the redcat ascent. use the 2 shocktowers to srew in place
A super easy print to keep your battery away from the gears on your Redcat Ascent. Here is where I installed it: No supports needed. I printed in PLA and it worked fine!
These body mounts allow you to mount the Injora IR60 body on the Redcat Ascent 18 truck. The body hinges on the rear about 120°, allowing it to stay open by itself and have full access to the internals. The front magnetic latch uses two…
Extended shock tower to allow more adjustability of the upper shock mounting location. I am personally using them with the Injora 59mm shocks, but there are enough options that the stock shock should work just fine and allow the shocks to…
A stand for the Redcat Ascent 18. One piece version but also included the single stand if that is your preference. Some notches on the bottom for rubber feet.
print 2x need to mirror 1 in the slicer need 2x 2.5mm screws and 2x 2.5 nuts near the slider.
Printed in Petg Rear shock towers, v3 has more mounting options
This is a MagSafe adapter that fits in the small tray above the shifter on the 2023 generation Subaru Ascent vehicles. It has a wire storage system build into the base so you can adjust the amount of cable length exiting the back of the…
Print this model as is with supports. I ended up using a brim on mine to keep the edges down during print. It's designed to fit this charger:…
Print in something with higher heat resistance than PLA. I printed in ASA for lightness, heat and UV resistance. Attach VTX to the Body with 4* M3x4 or M3x6 screws. The Cam-Top attaches to the Body with 4* M3 screws. Camera attaches using…
I designed this ultra-light canopy specifically for the Walksnail Ascent Lite Kit for TinyWhoops and Toothpicks . Since there are currently no other canopy options available for this kit, I decided to upload my design to fill the gap for…
A parametric remix of the "Nvidia DGX Spark - 10in rack mount" by Dan Marchenkov, re-worked so a taller ASUS Ascent GX10 (GB10) fits — it does not fit the original tray. Both parts (the main tray and the backing plate/bracket) were…
Printed this model in PLA+ but any other filament should work as well. I used M2.5*12mm screws to secure vrx and M3*40mm to connect two parts.
as requested a "deep bed" for the scent
Works as a combo with the top mounted cooling duct
I ran with 4 walls and 25% infill but I'm sure it would work with other variations.
As the Redcat Ascent 32 was launched, nobody made aftermarket wheels for it - so I created the replacement hex that converts from the Ascent 32 axle up to the standard hex size for 1.0" wheels. I printed in PLA on my Elegoo Neptune 4 Max.…
MT Ascent - Adjustable Height Model Turner / Work Table This is a print in place, Quick Operation Height Adjustable version of my original Model Turner, the adjustment range is 135mm to 200mm , the base can be used with all my other Model…
🟩 🟦 🟦 🟪 🟥 🟧 🟨 This is a cooling base for the ASUS Ascent GX10 , a GB10 based AI computer. The device typically runs very hot under load, and I would like to increase its life by helping it with cooling. In my tests using a constant…
A drop-in cooling stand for the ASUS Ascent GX10 (NVIDIA GB10 / DGX Spark family). The GX10 pulls intake air through its perforated bottom plate and exhausts out the rear. It can run into thermal limits, throttling & crash with sustained…
Designed for the Littleguyracingparts Super 8 axles, which means anything with an wheel to wheel of up to 13.5cm. Stock width is like 9.5cm. Works with stock axles, stock axles+hex extenders, Meus isos, Lgrp super 8s axles without hex…
The stock Redcat Ascent 18 battery tray doesn't give any room to access channel 3. This is a copy of the stock version with a notch to make it easier get a connector into channel 3.
Lower the ride height and soften the suspension on the Ascent 18 with zero preload lower cups. Print at.16 or lower from ABS, ASA, PETG, ETC.
I have a small form factor version as well. Get it here . Print in something with higher heat resistance than PLA. I printed in ASA for lightness, heat and UV resistance. Screw VTX to the Body with 4* M3x4 or M3x6 screws. The Cam-Holder…
Remove body attached retention hardware and glue in tailgate badge. Relocate control box. Replace front and rear frame spacers using original hardware and holes. Glue in 10x2mm magnets. Glue top pieces to body shell using lower magnets to…
The Ascent OC is a safety razor with a high-flex blade design that accommodates the simple but proven method of adjusting the shaving efficiency by simply turning the handle, which reduces the blade's flex and, in turn, increases the…
I am not sure why or what part is missing from my Subaru Ascent passenger side windshield wiper arm sprayer. Mine is now shooting everywhere except the windshield. I can spray people on the sidewalk and cars to my left and behind me. I…
A nice wall mount for your home ASUS Ascent GX10 LLM server. This mounting bracket can be mounted sideways and top down depending on your needs. There are little nodges for the feet so the GX10 will not slide out.
This is a mount I designed to attach the walksnail ascent VRX to the front rails of my HDZero goggles. It's tested on the V1 of the HDZero Goggles, but should work on the V2 also. The STL contains only one part, you need to mirror it in…
Print in something with higher heat resistance than PLA. I printed in ASA for lightness, heat and UV resistance. Attach VTX to the Body Lite+ with 2 of the short screws included in the kit. The Cam-Top attaches to the Body with 4* M3…
This is a switch blank for a Subaru Ascent for installing a RedArc Tow-Pro brake controller knob. This is a remix of vvander's design with a cutout for the indicator light and recess for the knob added. Note that the recess requires…
Hello everyone, I have vectorised a technical drawing of the Apollo 11 Lunar Module Ascent Stage and made it printable with a 0.4 nozzle. IMPORTANT: The illustration is very detailed, so slicing can take up to 10 minutes! Please note the…
This is a Caddx Walksnail Ascent Pro VRX mount for the HDzero BoxPro + FPV Goggles New version accommodates top mount as well as front mount, and folds flat for storage/transport. Use the top mount to reduce neck strain but you will need…
Apollo Lunar Ascent Stage Drone one small LEM for mankind This little remix of the other LEM drone originally was supposed to fly with the decent section but is too heavy for the drone I based it on. So just the ascent stage flies and…
Built for walksnail ascent camera, best print in TPU Features holes for screws for better camera stability
Insert for left dash that fits Redarc trailer brake controller.
GB10 / DGX Spark — Splittable Side-Vent Duct + Modular 10" Rack Ears A remix of **"2 x Node Nvidia DGX Spark (GB10) Cluster Side Vent Cooling Duct" by Henry Thomas** — thanks for the great base model! Fits GB10 boxes: NVIDIA DGX Spark and…
Insert for bottom row of Subaru cars (tested with Ascent 2022, but should work with any model that uses part number 83005AL020 ). If your model requires the knob on the top row (part number 83005AL010 ), you probably want @vvanders…
This fingerboard stairset is designed with rough golden ratio proportions all around. use the rail on top and hit the stair gap. Downloads include long rail alternate design. sticky tack or grip tape recommended to prevent slipping.
You need 8 M2 press-fit inserts and M2 screws to connect VTX and Camera to the cage, Pavo20 kit M2 may be used for cage connection. It's around 8g, the difference in mass between o3 and ascent lite makes this acceptable. 2 walls, 0% infill.
ASCENT A humpback whale bursts out of the sea. As it rises, the skin on its back turns into overlapping feathers, the feathers peel away on the wind, and a few lengths above the water they have become a flock of birds that arcs over its…
Print the bumpers with TPU / Flex Fix the Sidebumper with an M3 Screw
This project is designed to make it easier to build small Asus Ascent GX10 clusters. All parts fit very tightly together, which prevents the structure from moving. No screws are required. All parts were designed for printing with a 0.4 mm…
i make the roof top vtx mount with a walsnail ascent lite kit on my 1/18 scale hpi venture 18 hilux. i used M2 4mm screw for the camera mount and i insert the threaded heated M2 3mm(H)
Ascent lite+ mount for Mobula8
The sculpture depicts two figures navigating a spiraled staircase, symbolizing the intertwining journeys of life. With one figure ascending confidently and the other descending thoughtfully, it captures a moment of reflection and…
Case for Walksnail Ascent Goggles. Fits the googles with Powercable and Battery. Screws: M3x40mm Print Settings: 0.24 Layer and Fuzzyskin. Model was printed from PETG
This is a cooling assembly for Asus Ascent GX10 mini pc. Required parts: 4x M3x6 4x M3x25 4x M4x35 4x M4Washer 4x M4Nut There is an assembly image showing how to assemble the cooling solution. Fan used: NOCTUA NF-A12x25 5V PWM Optional:…
simple 1/18 scale jerrycan for rc crawlers
Sorry…this is a what? Every spring, Jews count 49 days between Passover and Shavuot . It's important to keep track because if you miss even one day, you can no longer say the blessing. Printing Instructions To get the contrasting colors,…
This is a mount I designed to attach the walksnail ascent VRX to the front rails of my HDZero goggles. It's tested on the V1 of the HDZero Goggles, but should work on the V2 also. The STL contains only one part, you need to mirror it in…
I have a small form factor version as well. Get it here . Print in something with higher heat resistance than PLA. I printed in ASA for lightness, heat and UV resistance. Screw VTX to the Body with 4* M3x4 or M3x6 screws. The Cam-Holder…
A nice wall mount for your home ASUS Ascent GX10 LLM server. This mounting bracket can be mounted sideways and top down depending on your needs. There are little nodges for the feet so the GX10 will not slide out.
Blank insert for 2024 Subaru Ascent(pictured with redarc trailer controller) for adding switch or other accessories.
Sorry…this is a what? Every spring, Jews count 49 days between Passover and Shavuot . It's important to keep track because if you miss even one day, you can no longer say the blessing. Printing Instructions To get the contrasting colors,…
The stock cargo lighting in the Subaru Ascent is inadequate, often obstructed by cargo, making the side light ineffective. This 3D-printed LED fixture addresses the issue by integrating a dedicated overhead light, powered by the existing…
A 3d-printable miniature of the hypothetical Saturn 8 rocket considered for the direct ascent alternative to the Apollo program
Fits a Vitamix Ascent container for removing the blade assembly. Printed in PLA+ with 20mm M3 screws used for extra re-enforcement against shearing - but probably wasn't needed. Rather than printing the part with a handle, I opted to use…
Cup holder adapter for 2023 Subaru Ascent so you can use larger water bottles
I liked the idea of the original model, I had trouble with the cable management and I decided to try a different charger. that didn't fit the original. I printed face down with PETG.
Nut/tool for removing the blade assembly from a Vitamix Ascent container. Use with channel lock pliers or big wrench
