Counting matching models…
I get annoyed every time I have to deal with the Ikea Metod feet when setting up a kitchen. Every time I put them on at an angle, as well as every time I move them, the feet break off, if they haven't fallen off before. So I constructed…
Overlay tile for the board game Gloomhaven. The large version is more like a full size wardrobe. The small version is probably closer to the correct size. Since obstacles do not block line of sight in the game I assumed they where below…
A lid holder that mounts inside a kitchen cabinet door using Velcro command strips. Can mount multiple side-by-sides to allow for storing more lids.
This rackmount adapter is designed to mount the TP-Link ER605 wireless router in a 10-inch network cabinet. The frame takes up 1 unit of rack space (1U) and is optimized for ventilation to ensure efficient heat dissipation. The adapter…
Information on the drivers to use and crossover design/schematics can be found here . I have now also designed some angled desktop stands for these speakers, can be found here This enclosure design is based on the work of the legendary…
This rackmount adapter is designed to mount the TP-Link TL-SG1008P switch in a 10-inch network cabinet. The frame takes up 1 unit of rack space (1U) and is optimized for ventilation to ensure efficient heat dissipation. The adapter can be…
DISCLAIMER: Please beware of the safety concern this may cause. If you intend to use it in a fridge/freezer or any place where a kid/pet might get stuck and suffocate, this might not be the solution unless you can guarantee the safety of…
First-in-first-out can organizer and dispenser for efficient pantry storage of cans. Great for keeping your oldest canned goods up front to keep your stock rotating and fresh. I looked at a bunch of these, but the designs were all oddly…
Divider for drawers in STANLEY “multi-use” cabinets. Quick & easy print – ideal for using up small amounts of filament. :) OpenSCAD files are included. Check out my feet for this cabinet.
This model is a wall mount for the inside of any standard Ikea kitchen cabinet that is designed to hold two of any standard type of SodaStream CO2 cylinders. By using the wall mount the usually unhandy and clunky SodaStream CO2 cylinders…
It is possible to use plastic zip ties - width up to 5mm. The design is for cables with a diameter of 6mm in my case ETH cat6. If a different diameter would be suitable, I can add...
I have been using Raaco Handyboxes for component storage and transport, and find a lot of space in them is wasted as I do not have enough of the small inserts, and also the smallest ones could have more compartments to save even more…
This rackmount adapter is designed to mount the TP-Link OC200 controller in a 10-inch network cabinet. The frame takes up 1 unit of rack space (1U) and is optimized for ventilation to ensure efficient heat dissipation. The adapter can be…
Here are some shelves my father made for my niece. The 2x2 and 2x4 are inspired by Ikea's Kallax line, the others are his original designs. There's even a little drawer to print for the 2x's.
tape to the back side of your cabinet doors, holds 1x or 2x mio drink mixes I use 3m tape for these
Plug for the threaded holes in the Platsa top/bottom plate. With 3mm hex to easily assemble them with a hex key from inside of the cabinet. Have only printed them in PETG as that was the white filament I had at the moment, guess PLA will…
Prints best detail on resin. But can be FDM printed also. Side cabinets included as a separate file also.
This is a copy of the original IKEA BRIMNES Plastic Gliding Foot. I redesigned it because I needed different feet heights. If you have a uneven floor like me you can simply print higher or lower feet. I have added also the STEP-File if…
Simple coat hanger for everything square. The width is 20mm, but can be scaled to accomodat other widths.
Filter holder for Prusa Enclosure and rack server cabinets (120x120 fan). It is cheap, fast to make and simple as possible. Holder is designed for Zortrax filter set (Hepa + Carbon), but any square filters up to 27mm thick will fit. You…
Corner Brackets for cabinets or shelves Print solid very strong Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Yes Supports: No Resolution: 0.2 Infill: 100% Filament: MatterHackers PLA,ABS any Notes: Corner Brackets…
The plastic door lock/latch (latch bolt) of the Cabinets/Drawers became brittle after a few years and had to be replaced. The replacement also went defective after a short time. It took me a few hours to draw and print the plastic part.…
I further remixed @SimonStrandvo_410750 's remix of Petr Vacek@PetrVacek_20701 's awesome model to accommodate IKEA cabinets. With short leg: adjustable from 103mm to ~140mm. Best to print this with supports ! See: Adjustable Furniture…
I have a couple of not-standard-size virtual pinball machines. Even with their feet extended, I find them a little too short to be comfortably played. I made these to put undr the feet to raise the cabinet to a more comfortable height.…
This design is part of my Mushroom Grow Tent (Martha Project). https://www.printables.com/de/model/968799-300-grow-tent-for-mushrooms-overview ------------------------- ◾ 2023-12-23: Update your Martha with an even further optimized air…
I bought some brand name child locks from a big box store. They were very cheaply made and kept breaking. I re-designed them to be stronger. I printed with 2mm walls and 100% infill. PLA is flexible enough for this. I used #6-0.75"…
An easily adjustable (parameterized) 3D printed lockdown bar for real or virtual pinball cabinets. Options included with or without a center Fire button. This was mostly designed for virtual pinball cabinets that are often custom sized…
These are some cool crystal doorknobs. These models are best printed with a resin printer to get the best clear crystal. However these can be printed with any 3d printer. These hole diameter for the bolt is 7.5mm however I included the…
The baking sheets used to just sit in this open cabinet, so I just put this little model together.
I made this to replace missing shelf bracket pegs for my bathroom mirror cabinet. The hole diameter is 5mm and it's a snug fit. Your cabinet holes/shelves may vary. These cost me approximately 3 cents in materials to print 3 of them,…
Simple divider for drawers in STANLEY cabinets with 3 × 3 drawers. Quick & easy print – ideal for using up small amounts of filament. OpenSCAD file is included. This is a remix of the design for cabinets with 6 × 5 drawers:…
A basic hook designed with Tinkercad that we designed and printed to hold our blinds tightly to the window frame
A model you can set up underneath your kitchen cabinets to secure wine or other types of spirit glasses. This model holds 4 glasses with a bottom plate diameter of 70 mm and a thickness of 3 mm. Feel free to modify it to your needs :)…
This custom 16 inch diameter 3 tier lazy susan spice rack was designed upon request for a friend and is made available for you for free. It's meant to fit in the corner of a counter, under over-counter cabinetry (at 16" inches or above ),…
A Parametric drawer separator for Stanley cabinets made with realthunder's FreeCAD link branch . You can also edit it with standard FreeCAD.
Sicherungsclip für Systemschränke des Herstellers LISTA. Securing clip for cabinets from the company LISTA.
This is a replacement Uline Locking Bar Guides for Storage Cabinets. Original part number for uline is H-1105-15 original MFG part number 944Gi. This is number 14 on page 3 of the following breakdown…
I added the drill bit size needed for most handles in the US. I also added the inches to the side of the guide so you don't have to guess. You can also just use it as a reference with your handles to see what holes you need. The bottom…
Here's a model that I made for the Frosthaven Metal Cabinet overlay! There are four such tokens in the game, so I'd recommend printing out all four of them, especially because they're nice and easy to print with no support required! Not…
Two small organiser cabinets, 96x140mm and 140x140mm. Both are 77mm in depth The drawers fits both cabinets
Handles come in 5 different standard sizes (center to center): ❌ 96mm ✔ 128mm ✔ 160mm ✔ 192mm ❌ 320mm ✔ Tested - PLA | ❌ Not tested TOOLS 🧰 Philips* screwdriver (do NOT use a drill ❗ ); 3.5 diameter wood screw (the length varies depending…
I bought some IKEA EKET cabinets (with door and with drawers) that I wanted to place on a carpet but needed them to be placed at a certain distance from the wall (due to reasons). Unfortunately the provided spacers weren't long enough for…
Pimp your Bisley steel cabinet with a colourful new lock handle and/or cover up a clumsy mistake! Should work for all cabinets with the pictured horizontal lock mechanism. Manufacturer seems to have only the whole assembly as a (fairly…
I was tired of all those D1 mini shields cluttering my desk and drawers, so I made this little thing. It is good for up to 28 shields (in reality more like 20) standing upright in a standard hardware storage cabinet drawer. The dimensions…
This model works with the original Back STL provided via the original (included here only as a convenience). I printed in white Polymaker ASA for UV resistance and durability in a kitchen environment. These were printed without supports…
Trim to hide the lower screws of Ikea furniture, depending on the printer the scale can be adjusted.
SMC bracket for mounting a Frontier GPON ONT model FOG421 into common Structured Media Cabinets. This includes printed mounting tabs for hanging the device, so no screws are necessary to be added after printing. Use the appropriate…
Replacement battery cabinets to kitbash an Aristo-Craft U25B to a reasonable likeness U33B. These could also be used to simulate other GE U-boats as well.
In v3 I included holes for guiding drill bits. I used it to build 12mm plywood drawers and a 15mm plywood cabinet. I printed 6 and was barely enough, next build I'll print 2 more. They fit snugly and can be hard to remove after a glue-up,…
Shelf Bracket Peg for Bathroom Cabinets for 5 mm hole diameter. You can change sizes for your dimentions in freecad file. Or adjust X-Y contour compensation in OrcaSlicer for better fit
The "SCREW IT!" vase is a fully 3D printable vase that clamps to your shelves or other places, wherever it fits! You can assemble the vase by following these instructions; 1. Remove support after printing the BODY. 2. Insert SCREW into…
SMC bracket for mounting D-Link DMS-105 switches into common Leviton, Legrand, and OnQ Structured Media Cabinets. Supported devices include: D-Link DMS-105 5-port 2.5 GbE Ethernet Switch This includes printed mounting tabs for hanging the…
For use with screws with a diameter around 3mm! I printed mine on Copper Silk PLA. I recommend going slower to avoid stringing. Also, flip upside down when printing to avoid using supports.
Can be installed either side. Diameter of dowel is the same as genuine wooden IKEA dowels which can be used as an alternative. Zero extra clearance to make sure it stays attached to the cabinet. No need for supports when printing
it is the same filter as here https://www.printables.com/de/model/541332-hepa-filter-holder-for-prusa-enclosure-and-rack-se from KFORMS I only fixed the stl in the first file. In the second file i added holes for pushing the filters out.…
Check my other IKEA designs: Ikea Metod Screw On Leg Extender (402.055.99) IKEA Metod Back 10mm Spacer Replacement (10036383 or 10039201) Why Do you have a robot vacuum that can’t clean under your IKEA Metod cabinets? The default 8 cm…
The idea is this is a simple passthrough (flanged on one side), that can be glued or taped in place on millwork doors, etc. The version I printed is 125% in X/Y coordinates, which makes it about 6" height and width.
What it is Sometimes a knob that sticks out isn't that practical. This model is literally the opposite. Modestly designed, flat and intrinsically flexible. It won't hurt or break if you bump into it. → Useful in confined spaces or to…
I needed some ventilations to some exterior boxes, but didn't wanted it to allow entering water, so I designed these ventilations/breather pieces. Here you will find two different designs, one to be fitted at the top, another one to be…
Is your design lab large and roomy, or small and cozy? Either way, being productive requires that work areas and surfaces be clear of clutter and tools and components be within easy reach. In our lab, we have a seemingly endless array of…
Feet for STANLEY “multi-use” cabinets. Ideal in combination with round felt stickers (17–20 mm). The feet snap onto the cabinet's stacking pins and hold without any glue. You want to print four corner feet and two center feet. You can…
I was looking for an easy, non-permanent system for storing filament spools in my BESTA (IKEA) storage cabinet. Materials Required: (2x) Printed Dowel Brackets (min.) (2x) #4 by 3/4in wood screws for each Dowel Bracket (2x) 1in dia. wood…
Stackable braces to hold various pieces off of the ground or floor while painting or staining. You can stack them to let all of your pieces dry without worry of them getting marked up. Multiple hole for screws to attached to your piece or…
Description This modular spice rack system is designed for super tight cabinet spaces , fitting easily in as little as 10 inches of height . Fully 3D printable, modular, and stackable — it’s perfect for organizing spices in compact…
Hook for the Ikea Ekenabben cabinets to hang things off the side
Needed to cover a 51mm hole where the investor changed the decission and the hole need to be in different location. For scaling use the 100mm file. If You want 35mm just scale to 35% on X and Y, scale Z depending on the thickness You want.
This model contains mounts for mounting 2020 aluminium extrusion to the inside of Ikea Pax and other cabinets that use the same system for mounting shelves using 5 mm blind holes at a 32 mm pitch. There are two variants of the part: One…
This plastic part is used to holf boards underneath kitchen furniture. It was broken and I designed new one. Print with ABS, PETG, ASA or alike.
-Miniature Sink Counter with Dishwasher & Cabinets -Glue together - Sink "sold" seperatly
..:: РУССКИЙ ::.. Устройство для сверления отверстий в стене для подрозетников. Отверстие диаметром 68 мм. Между центрами отверстий 71 мм. Крепить к стене можно как саморезами на стадии ремонта, так и на двухсторонний скотч после ремонта.…
Hole Drilling JIG that helps you drill precise holes for shelving for different IKEA Cabinets. I have this JIG with the IKEA Metod (IKEA Sektion) to make middle holes between two holes. The drill bit that is used to drill the holes is a…
The original is great for going through shelves or a desk top. I needed it a little longer.
Found the Top Door Hook by Lowd14 stylish. So I just cut it a little and reinforced it for sticking on cabinets.
Customizable bumper for table, cabinet etc.. corners. Possible use cases: Prevent cabinet corner from damaging the door Baby proof sharp corners of the table Protect corners of the glass, veneer or any other sheet If you customize and…
Fits both Vallstena and Utrusta drawer fronts for a 3/16" hole.
This simpe knob prints in about 30 minutes an needs a simple bore of 30mm width and 10mm depth. Depending on the prinitng parameters (you might need to scale up 1 or 2%) it fits without glue. The model should easily be scaleable for…
They are used for cheap kitchens or mounting these boxes on thin surfaces. 2 options. The open bottom is to be used if needed to install after the wiring is in place. Enclosed if you are smart and remember to use it before wiring :) The…
Dyson vacuum cleaners - Extension to suck behind cabinets and crannies. The gCode files are created for the Prusa mini. I used a 30mm Gardena pond tube as a hose. German: Die gCode Dateien sind für den Prusa mini erstellt. Als Schlauch…
Customizable knobs with the name of your children. You can print them by changing color to enhance the names. In this case, I have added the code M600 to make the color change, at the height of 14.2 mm. To fix them, you can directly screw…
Guide to replace the small plastic retainers that fall out and typically get lost on ULINE locking cabinets
This is a bracket for supporting drawer slides in Wellborn brand cabinetry. This track works as-is for the left and right track, no need to mirror it. Print instructions Printer: Mk2.5s </div> Rafts: No Supports: Yes </div> Resolution:…
I created this when an old magnetic catch mounted on my kitchen cabinet broke. It was faster to design and print this than to find a similar replacement. Category: Kitchen & Dining
this is a push pin designed to help stubborn doors open when unlocked
Designed for the sektion cabinets but works others as well
Today I've got some really simple cabinet / wardrobes. These are props made by hand for my Modular Barovia Campaign - I'm slowly working through the full list of props needed for GMs to run the "Death House" one shot and other parts of…
Just little divider to separate the content of the drawers of a small parts magazine (for example LUX Kleinteilemagazin Professional 44). Fully parameterized. You can add a "helper" on each side. The helper helps you to grab little nuts…
SlideGuard is a simple helper to add an extra layer of protection to your french door cabinet doors (double swing style) from wandering hands. While no device can substitute for careful supervision, SlideGuard offers a simple deterrent to…
## IKEA BESTÅ Wall Mount Support Bracket — Shallow (20cm) Cabinets Supplementary wall-mount bracket for IKEA BESTÅ shallow (20cm depth) cabinets. Bolts directly into the cabinet's factory-drilled M8 hole — no modification required.…
Schnell und einfach Kleiderbügel vor dem Einräumen am PAX parken! Attach your clothes hanger easy and simple on a PAX cabinet! Habe meine in weißem PLA gedruckt damit die Halter zu den Türen passen (siehe Bilder), kann aber in jeder…
Welcome to Dave's INF~ Modular Cable Management System Unlock the potential of a pristine, organized environment with our modular cable management system. Perfect for seamlessly concealing wires in server racks, beneath desks, and within…
Simple trash bag dispenser with no moving parts. Will most likely need to cut the model in to a few pieces to print on a standard printer. Let me know if you want a cut file as well or a file with dowel holes for easy assembly. I print…
There are 2 sets of stl-files, one for machine screws (ms...stl) and one for wood screws or other things (ws...stl). Each set has 2 groups. One group with 8 mm between the 2 eylets for short screws, indicated with ...-s.stl and one group…
Removable P2S coil holder for narrow cabinets External P2S coil holder up to 75 mm wide, removable, compatible with Bambu P2s. We have included a new coil holder with a direct PS2 connection on the left side (the right side needs to be…
Towel holder for holding towels or other stuff to the wall or cabinets. place two strips of double sided tape to the back and enjoy your towel holder in the bathroom, kitchen or toilet! Can even hang scheur calendars!
lock for caravans and cabinets
permanent twin hook that mounts from the top onto a cabinet carcass or furniture panel
Replacement latch tongue made for the EVETOFTE shoe cabinet from Jysk but it should work for all similar latching locks. It should work for similar mechanisms as well. For further details please check the attached picture with the…
This is a shelf to provide additional storage area in Namco Blanc/Noir arcade cabinets above where the cabinet link sliding door is at the bottom of the cabinet. I use this for adding additional A/V gear that I have added. When printing…
This light-duty hook is designed specifically for NewAge garage cabinet systems with slotted side panels. It slides directly into the factory slots for a clean, secure fit—no drilling, no magnets, no adhesive. Perfect for organizing…
Socket for import cabinet drawers.
