Counting matching models…
…Please be sure to hit like & post a make, I'd love to see your prints! EDIT: Finally! STEP file has been added!! Sorry it took so long guys, enjoy!! Add some class to your Voron with this awesome canopy / top hat! If you have a smaller…
Support my work +++ I will do my best to maintain and improve the project with incremental upgrades, but maintenance takes time and effort. If you wish to support my work and motivate me please consider to give me a donation +++…
This is a canopy for the BetaFPV Air Tinywhoops, like the Air65 and Air75. The longer tail section allows a lower camera angle to be set. I also made a widening in the area of the right holder to additionally fix the antenna connector. I…
Whether the dog chewed your lens cap, or it fell off a cliff during that last hike, the solution is one print away. Recommendations: Print Material: PLA Infill Percent: 15% Layer height: .15 (a layer height greater than .15 will not work…
Canopy for the Voron 2.4. Will need to be printed with supports, corner for fan will need to be mirrored for one side. Will work with 250, 300, & 350. Will use the standard acrylic top panel. Spots for 60mm fans with spacing for charcoal…
Hot shoe cover designed to fit Canon EOS cameras perfectly. A variant better suited for Canon FD cameras can be found here . Print Settings Resolution: 0.1 mm Infill: 100%
Two seats canoe in 1/10 scale with paddles
This adapter allows you to mount any finite RMS microscope objective (i.e. objectives that are marked with "160mm" rather than "infinity") on your Sony A, Sony E / FE, Canon EF / EF-S, Canon RF, Canon M, Nikon F, Nikon Z, Fujifilm X,…
Added more sizes to Wojtek's LP-E6 battery holder. Should be able to print without any supports in the provided orientation.
A lens hood for Canon EF 50mm f1.8 STM lenses. Can be used both as as hood and as a protective case. Print Settings Resolution: 0.1mm Infill: 100%
Remix from “ Air65 Canopy (low angle) ” by raNn . Une nouvelle canopy à imprimer en TPU pour le BetaFPV AIR65 : Incassable Permet des tilts beaucoup plus bas Attention : Ce n'est pas indispensable, mais une impression “dur” facilitera les…
BiQu H2 fanduct for a single 5015 fan Parts Needed: 2x M2.5 x 6 countersunk screws 2x M3 Nuts 2x M3 x 24 screws Printsettings: Layerhight: < 0.15mm Support Needed BiQu H2 fanduct for a Dual 5015 fan Parts Needed: 2x M2.5 x 6 countersunk…
Overengineered rear lens cap for Canon EOS RF lenses. Missing the align notch and stopper. Print instructions Print .1 or 0.2 mm P.S. Donations welcome, my cat keeps chomping the filament.
This is a printable model of the mount found on Canon EF/EF-S lenses, which you can use to design accessories like extension tubes or custom lenses. Print at 0.1mm layer height, in PETG (recommended) or another filament like PLA. This is…
Quick to print, support-free design. The Volcano WindWarden adapter mounts a 5015 blower for improved cooling after upgrading to a Volcano hotend. No screws are needed to hold the fan — it clips in securely. The height is adjustable to…
UPDATE 3: IMPORTANT only use these new files with the cutout for the U.FL socket (see images). The old design by BetaFPV likes to knock the U.FL right off the board… Ask me how I know. If you're in a similar situation, I wrote up a quick…
In Egyptian mythology, Duamutef was one of the four Sons of Horus, tasked with protecting the stomach of the deceased. Represented by the Jackal, he is the guardian of the East. This model is a stylistic recreation of a museum-style…
This is a Volcano with base for the Vinegar and Baking soda and dish soap experiment, I have included holes for TPU printable feet and Plug for the bottom (10-15% infill, recommend raft for TPU feet) . For the volcano, I printed it on the…
2023-09-12 version 3: moved the probe so that it can be adjusted without disassembling the entire shroud. Added both the Bambuslicer and the stl files. Lately I attached a heat sink to the front servo (https://amzn.eu/d/e68hmoo) because I…
When the 4x microscope objective available from “Reakway” is mounted 150mm away from a camera's sensor, it works wonderfully for photography, covering a full-frame image sensor with a nice sharp image. You can find my standard…
Fits Canoe paddles by handle or paddle Garden tool shafts up to 35 mm Garden tool heads (shovels, rakes, etc) D-shape handles Conveniently, it grabs most rubberized garden tool handles … Design Bore diameter is 35 mm, which should be good…
This is a Lens Hood for a 58 mm Canon EOS Lens. Suitable for a focal length from circa 18mm
I wanted a compact way to store spare nozzles, but nothing I found matched all my criteria: Gridfinity compatible and stackable Compact with maximum storage capacity Designed for Ankermake nozzles This bin will store 16 Ankermake nozzles…
scale 1/72 On my cults page you can download planes like this one on a larger scale and detail, they are for sale for 10 euros https://cults3d.com/es/usuarios/ivangonzalezm/creaci%C3%B3n missing rudder parts included excuse me After…
A simple island style boat/ canoe with rounded sides and flat bottom. No support needed.
Print in TPU, organic tree supports. I weighed it at 1.7g. There's room to make it lighter for sure, but I also want it durable. Feel free to give me feedback!
Thanks to the amazing work from the Voron team! I added a printhead for the Volcano variant of E3DV6. It is a simple extension of the part cooling ducts from the original Voron Stealthburner E3DV6 printhead. Not the nicest looking mod…
A Duct-Extended v6 Printhead for the Stealthburner The Voron Stealthburner toolhead includes a printhead module that is compatible with a standard v6 hotend. In this mod I attempted to replicate bythorsthunder's mod for the Stealthburner…
Proper clearance, lens orientation and flange focal distance. Tested with Helios 44M-4 and Beroflex 135mm F2.8.
Replica of the TIE/d Defender from Star Wars. It comes in two versions. The canon version is based on its depiction in Rebels, the other version is based on its (most common) depiction in Legends. The only difference between the canon and…
Rear lens cap to suit Canon EF and EF-S lenses. Print Settings Supports: No Resolution: 0.2mm Infill: 100% Filament: Plasty Mladeč PLA Black Slicing settings: Perimeters: 2 Seam position: Random The cap has three internal flanges which…
I am too lazy to enter what you need as screws but you only need m3 type and a couple nuts. Some holes are self threaded without nuts, you can figure it out if you inspect f3d file. Also bltouch mount is a bit high from nozzle you need…
A perfect day in Printer Island is about the be ruined by an eruption of Mount PLA! https://www.youtube.com/watch?v=3cVqtMMg_AE This thing is a volcano, which uses an LED illuminated ultrasonic mist generator to bring it alive. Assembly…
I suggest ordering the unassembled or Low Profile variant of beacon, or you may run into clearance issues. You MUST edit your config to make sure you don't hit the probe on your rear Z-axis lead screw constraint! :) 3.17.23 Update v1.3…
T-ring adaptors for 2" and 1.25", should work on any telescope. The adaptor if of the EF type, it should work on any Canon EOS cameras.
Сопла, крышка, подсветка, съёмные, для удобства печати и уменьшения нагрузки. Для термобарьера толщиной 27 мм. Добавил версию, с повышенной жесткостью, вторыми креплениями для вентиляторов, и немного укороченными соплами. Изолировал левый…
Modified Tri horn duct for better flow with volcano hotends. Tested with Phaetus Rapido UHF and CHT Volcano nozzle Update 05/10/2022. File models fixed
This is a printable body cap for FD mount Canon cameras, such as the T50, T70, T90, F1, A1, AE1 and others… I modeled this cap after an existing cap. The print is not quite so simple, as the guides for the bayonet catch have a slope. I…
For those of you who like to go the minimalist route... From the same designer that brought you all the popular Hero Me remixes... MediaMan introduces the The E3D Minimalist. A simple, clean, lightweight, yet strong mount for your…
Adapts Canon EF/ EF-S lenses to Sony E-Mount bodies. That is all, no lock, no frills.
Update Feb25: Thanks for almost 300 downloads! Full Step Files available for Purchase from my Printables Store Here - perfect for alteration and customization. Free STL Files for 3D Printing below: Set of Modular Lens Cases, Protection…
### UPDATE! Now the text is in correct horizontal orientation Hi, this is a cap/cover for Canon's camera body with mount ef / ef-s Print settings: Layer height: Any, I used 0,2mm Material: Any, I used PETG Supports: Yes, only on build…
This is a hood for Canon kit lens. Three models are included, rounded hood, petal hood and a base that you can use to design your own model. f3d file is included.
…Please at least be sure to hit like & post a make, I'd love to see your prints! Use volcano nozzles in your sv06 plus. DONT LEAVE A BAD REVIEW BECAUSE YOU DID A BAD PRINT! Like the single reviewer here! That's just not cool. It’s…
The Embraer EMB 314 (A-29) Super Tucano, Brazil's answer to a light attack CAS aircraft. It is a highly versatile and low-cost turbo-prop powered craft, can be fitted with a vast array of munitions, and is operated by nations worldwide.…
The canopy is modified to be directly usable with the BetaFPV Meteor 75 Pro O4 hardware, i.e. the surfaces were flattened to account for the screw heads, and the antenna holder was altered to fit the fat O4 Lite antenna. Print in TPU or…
A convenient way to store up to 5 Canon LP-E6-style batteries on a 1x3 Gridfinity plate. Related model for the LP-EC Canon Charger .
Someone in the comments mentioned that original canopy is too thin for TPU so I added 0.5mm thickness for it
We have templates for both male and female pairs of the RF mount. They fit my camera and lenses without further modification. Having done this, I belive it is possible to have a mount that fits both RF and EF - you just have to cut a bit…
If you're looking for a replacement protective battery cover this is it. Print settings: Printed in PLA, .6/.4mm nozzle, .2mm layer height. Will print solid with a .6 or a .4mm nozzle if printed with 2 walls and at least 3 top/bottom…
A connector piece between your Canon camera and your tripod. Incase you loose it or if you need a replacement piece. Made in Fusion 360
Main features: Stairstep pattern on the inside to further reduce flaring (mimics the original, was a pain to model) Clicks when fully twisted onto the lens Can be put on backward for storage and trasport Has the same markings for…
Thanks to the linked makers I was able to merge them and to create this EF to M42 lens adapter. It works well for me but it is possible to improve it. If you printed the design you have to drill a hole at the spot where a camera lens…
Miminal box for 20 nozzle volcano with interlocking closure. The top cover has a small offset and fits snugly with the bottom.
Volcano fan shroud for MK3s+ This is a meshmix of the mk3s+ fan shroud to work with Volcano Hotend. I have not found a volcano shroud for the mk3s+ so I remixed one from the original Prusa fan shroud. print in ASA or ABS! (PETG and PLA…
The Canon EFS 18-135 Lens is a very good lens, but it does not come with a hood. I tried several different models that others had posted, but none seemed to fit the bill, so I made my own. This model is reversable so it will store well.…
The MAK Vector Duct Features: Open views of the hotend Easy maintenance construction for easy nozzle changes Fully enclosed 5015 fan for style Cable management arm Solid carriage mount Still a work in progress. More extruder options and…
Canopic jars were used by ancient Egyptians to store and protect the mummified organs of the dead. The four sons of Horus, depicted on the lids, are jackal-headed Duamutef who protects the stomach, baboon-headed Hapi who protects the…
Remix of "A hot shoe cover designed to fit Canon EOS cameras perfectly." by JP that does not block internal flash.
lightweight and easy to print. correct flow direction adjustment ability no supports needed for fan fastening you need to cut m4 thread in hole. i used self made m4 tap and m4 x 20 screws. use standard print settings. don't forget to…
With these files you can now directly attach your camera as a normal observational eyepiece, just tighten them in your 1.25" or 2" eyepiece holder. NOTE: If it doesn´t fit well for your telescope, maybe you can play with the tolerance of…
The best can holder! Has a super snug fit and prints really nicely. I made mine out of PLA but I'm sure ASA would be perfect for the UV resistantance. PRINT SETTINGS: -No supports needed -0.2mm Layer height (Not too specific. Really…
BetaFPV C03 camera mount The design combines the idea of brighfive's Bribrain LowRider version requested by the legendary TDog. Features: Available Angles: 10°-60° @ 1° interval apart Weight: Approx. 0.573g Mounting Pattern: 25.5x25.5mm…
Behold The Volcano iPhone stand! This iPhone and mobile phone stand came out of one basic question: -How can we design a phone stand that has built in three most usable angles for a mobile phone, and doing that in a simple and iconic…
A simple lens hood for your CANON EF/EFS lenses. Prevent undesired glare, improve contrast in your photos, and add a personal touch to your camera gear. The stepped inner surface improves light-blocking performance. Compatibility This…
This part is designed to be printable without any support material. A well adjusted printer is necessary fo a tight fit. Extension tubes are mainly used to reduce the focus distance of a lens for macro photo. The sample photos are taken…
25.5х25.5 Canopy Walksnail 1S lite kit camera (mobula, meteor etc) Weight = 1.7g Angle = 30
Floats like a dream too! Designed originally as wedding favours, this canoe is great for any canoeing or outdoor enthusiast. Printing instructions: With an MMU or other colour printer (or if you want one solidly coloured piece), choose…
Print upside down. So that the funnel is at the bottom and the thread is at the top. no supports necessary.
Print model in PLA and plug in TPU
The newest version of my Lens Cap Holders. Now with more supported filter diameters. The following diameters are supported: Canon: 49mm/58mm/62mm/67mm/72mm/77mm/82mm Nikon: 52mm/55mm/58mm/62mm/67mm/72mm/77mm/82mm Nikon (extended):…
Print the volcano put down some vinegard from the top hole add few gr of baking soda and wait for the eruption You want to start with few vinegard and small quantity of baking soda and then decide how much you want to erupt the volcano…
Contains an opening for a hose / air stone as well as openings on the bottom for weights
I designed this new canopy for Mobula 6 to solve some problems: It has support for copper antenna on the rear. Upgrade recommended for yours. Support for a small 9mm buzzer. As it is very small, a buzzer is useful to locate it if it falls…
This is a fully printed canon RF body to EF lens Tilt adapter. It allows you to create the “tilt shift” effect with any EF lens. It will also work with any EF body to other lens adapters, I've personally used Nikon F mount, Olympus OM…
I designed the fit to be perfect when printed in Prusament PETG, I haven't tried Prusament PLA or other filaments (yet). The battery type “LP-E17” is embossed on one side. On the other side the same is done in Braille.
This is a rear lens cap that fits Canon EF and RF series lens. Print with supports enabled for the benefit of the three screw segments (I'm not sure what to call them).
Edit 06/07/25: Added smooth versions of the grip without the finger slots and uploaded the fusion360 files to make life easier for anyone that wants to remix, I didn't realize in all this time that I didn't upload it :( Post your make if…
HOW I USE IT: ENDER 5 PLUS: https://bit.ly/2YHzpws BMG: clon:…
This is a canoe with a quote by Henry David Thoreau: "Rise, free from care, before the dawn and seek adventure." Great for outdoor enthusiasts, as a gift or as a model for your desk. Print instructions Category: Models Print with the…
fits well on my canon 80D but it should be compatible with all these too - 450D 500D 550D 600D 650D 700D 750D 760D 800D 77D 100D 1000D 1100D 1300D, EF Rebel T6s T6i T6 T5i T5 T4i T3i T3 T2i and more printed in one piece with PET-G (for…
I am not sure if the name for this part is right... I searched quite a while for the correct translation. But at first I didn't even know the german word.... :D In german it is called "Abzweigbaldachin" so the direct translation should be…
I crashed my Betafpv Cetus pro and couldn't wait on Frames to come in the mail. I took the hole spacing from NSA imperfect tiny whoop. I removed some structural components from beta75X Frame to get the Cetus Pro Flight Controller to fit…
I added alternative lever that uses M2x5mm (or longer cut to size) screw as a locking pin, it may scratch your lenses but is stronger and more reliable. To secure the screw in the lever you can use some leftover plastic from…
Remix of https://www.thingiverse.com/thing:4584743 for use with 5015 cooling fan. Haven't actually printed this yet! Print at 0.2mm layer height or below for best overhangs. EDIT 2020-12-12: The first version of this duct was completely…
Canon FD to RF adapter. Printed in two parts. Wet sand with 400 grit so that you get exactly 22mm height. 3x10mm M2 screws and glue in place when all fits well. Printed in CF-PETG (Atomic filament). 3 perimeter 5 bottom and 7 top layers…
Hi there. Here you are! An Mario Style piggy bank with a canon on top, inspired by Nintendo's WII Super Mario Bros. Level-Canon. The canon can be rotated and tilted. The piggy bank is also available in smaller scale, adjusted for IKEA…
Uses the following bolts/nuts: 1x M10*50 bolt 1x M10*20 bolt 3x M10 nuts 1x M6*40 1x M6 nut
3D printable canoe , compatible with Lego minifigures
An easy-to-print rear lens cap for Canon EF or EF-S lenses with Canon logo and orienation mark. I tried several models, this fits very well and looks pretty much like an original cap. Prints well in either orientation. Tip: If you happen…
This is a remix of the original nozzlebox with options that fit Volcano and MK8 nozzles. Like the original, it prints in place and is locked by a magnet (6x2mm!) and an M3x6 (or smaller) screw. It doesn't come with any markings so that…
A simple lens hood for your CANON EF/EFS lenses. Prevent undesired glare, improve contrast in your photos, and add a personal touch to your camera gear. Check out our growing collection of 3D printable designs for Photography ! Follow us…
Canon hotshoe - Action camera mount (GoPro, Insta360,...)
I was after a grid for my Canon 580 EXII speedlight, but none of the ones I could buy really appealed to me. They all seem a bit “clunky”, held together with magnets, rubber bands or Velcro. I figured there had to be a neater way. These…
(Files belong to their respective and linked owners.) Please email/contact me for immediate changes such as incorrect credit or placement, etc. I take no credit for any of these designs except for the extremely basic remix of some of the…
Based on my design for the eco camera, I developed the lux version as well. Please let me know if you'd like more angles and any modifications. Link to the eco version:…
It's a modifified Taurus cooling duct to be used with a voolcano heatblock and nozzle. I've also made heatbreak fan mode that uses stock 4010 fan (it's lighter than the stock setup). If you print from ASA/ABS remember to scale model for…
![BetaFPV C03 camera mount/canopy [Improved Complete Set]](https://media.printables.com/media/prints/5388c6c5-f443-476e-a91c-2cb185f211f6/images/11110340_e9dbe0a0-128d-4b63-b2fb-100d6291ac5f_1c42e2f3-7b8f-4de9-a9d5-c1a2f3042f00/screenshot-2025-11-08-212802.png)
