Search results: carbur

Sort order

148 models

P
Printablesrreibel

Carburetor Workstand

A work stand for working on 4-bbl carburetors with the narrower bolt pattern (4.25" x 5.625"). This fits a Carter Thermoquad (shown in pic) and I believe also the Rochester Quadrajet. This is based on the carburetor work stand print…

Downloads
541
Likes
43
Rating
5
P
PrintablesAcomisp

Gasket for Carburetor

This is an experiment replacing a normal gasket with a TPU made gasket for a lawnmower carburetor. All credit goes to The_Eddies on youtube for this brilliant idea and design.

Downloads
432
Likes
34
Rating
5
P
Printablesbglasford1

VW Engine - Carburetor

This is the carburetors required for the VW Engine model. These are EMPI two barrel carburetors. Two are required giving one barrel per cylinder. Refer to the assembly instruction for the parts required.

Downloads
423
Likes
68
Rating
5
P
PrintablesLolmodule

Carburetor storage hat

This model was designed to fit a 4160 750 cfm Holley carb with a choke horn. It should fit any 4150/ 4160 carb with no issues and may also fit others. I used a cheap carb stud from amazon cut down to hold it during storage. If printed…

Downloads
343
Likes
30
Rating
5
P
PrintablesCrackFox

90 degree screwdriver for carburetor mixture

This is a 90 bit holder for 1/4 hobby screwdriver bits designed to make it easier to adjust the mixture screw on my Honda Nighthawk Carburetors. The middle carbs are still a little difficult but much easier than using a regular…

Downloads
304
Likes
44
Rating
3.33
P
PrintablesRPI

Carburetor tool splined

This is a great tool but had to make a small change to fit my carburetor

Downloads
272
Likes
8
Rating
0
P
Printablesossifragus

Chainsaw Carburetor Air Valve Lever Arm

My chainsaw's carburetor has a secondary air inlet with its own valve plate. The lever in this model actuates that valve plate. A projection on the throttle linkage pushes this lever to open the valve plate at high speed. While doing some…

Downloads
267
Likes
12
Rating
5
P
PrintablesHomeBrewRacing

DRZ400 Airbox to FCR39 Carburetor Adapter

I pulled the STL into onshape and tried my best to replicate it, but that isn't always easy. It fits exactly the same as the original, except with better clearance near the jets (see the photo of the original's clearance). V1.2 update:…

Downloads
252
Likes
11
Rating
0
P
Printablesjmynheir

Ryobi(and other) Blower/Trimmer Carburetor Adjustment Tool

In this publishing I have included stls for 2 designs for the Carburetor adjustment tool. I used a Ryobi R09050 blower for testing and fabrication. I also included the blend file that I created the peices so you can modify in any way you…

Downloads
244
Likes
11
Rating
5
P
PrintablesGixxer

Carburetor float level gauge

I lost my original carburetor adjustment gauge. After seeing a tool I purchased for $4 dollars twenty years ago is now $20 I decided to print one. This isn't my idea or design but is the most popular type of tool on the market. It's…

Downloads
231
Likes
15
Rating
4.5

Lada 2105 carburator velocity stack for 1.5l engine

Velocity stack for a Lada carburator. I recommend ABS/ASA/CF NYLON for printing.

Downloads
199
Likes
23
Rating
0
P
Printablesjulien junique

Box dellorto carburetor jet

Boîte de rangement de gicleur de carburateur Dellorto. Dellorto Carburetor Jet Storage Box.

Downloads
197
Likes
9
Rating
5
P
PrintablesGaabstakiller96

Vacuum cap , Carburetor cap

Cap for vacuum or carburator storage small-1/4 medium =5/16 large=3/8

Downloads
179
Likes
9
Rating
5
P
Printablesszprusa

Simson S51 carburetor vent pipe clip with FreeCAD file

I printed it with PETG 0.6mm nozzle 0.2mm layer height 3 perimeter After I clamped in place I used a zip tie to secure it. About FreeCAD . About FreeCAD Realthunder fork .

Downloads
163
Likes
29
Rating
0
P
PrintablesMr. Sullivan

4500 Series Carburetor (Dominator) Base Riser and Gasket 1-1/8 in. Tall

This model is a 1-1/8 in. riser for use under the base of a Holley 4500 Series Dominator Carb. Designed for use with the 1050cfm model. I printed the file with Nylon-CF with 25 percent gyroid infill 0.2mm layer lines and 4 walls. To…

Downloads
159
Likes
17
Rating
0
P
Printablesp0tat0s

Carburetor Jet Box

Noticed the similarity in size between a v6 nozzle and vm18 jet so I whipped up this little remix of Reven's nozzle box, this uses the .2mm tolerance version as a base. First print with the original hinges broke coming off the bed so I…

Downloads
156
Likes
18
Rating
0
P
PrintablesChnillapoil

Stihl carburator Allen nut driver

This is a 4mm nut driver for tuning Stihl HL94 carburator. I suggest to print the handle at 20% infill and the rod at 100% by "modify settings for overlaps" / infill 100% inside the support blocker(in Cura). Print Settings Printer Brand:…

Downloads
149
Likes
22
Rating
5
P
Printablesjjbunn

Velocity Stack Mesh Filter for Weber Carburetor (2")

A filter (around 2mm grid size) that inserts into a 2" velocity stack, as used on e.g. Weber carburetors Category: Automotive

Downloads
126
Likes
10
Rating
0
P
PrintablesHeine Sørensen

Insulator spacer Weber carburettor 38mm DGAS / DGMS bakelite replacement

PETG and so many walls that the thing is solid ..and just send it.

Downloads
123
Likes
6
Rating
0
P
Printablesdancan13f

VW Type 1 Engine - Carburetor Remix

This add-on is a high-quality piece with highly realistic details. Congratulations to the creator of the original piece. Look the Assembly.pdf for details.

Downloads
115
Likes
18
Rating
0
P
PrintablesDerakCZ

Carburetor

very accurate model of the 22 mm carb for 212 cc engines

Downloads
112
Likes
11
Rating
0
P
PrintablesMr. Sullivan

Dragster Air Scoop and Mount/Arrestor For Dominator 4500 Series Carburetor

This is a dragster style carburetor scoop I designed for my boat. It requires quite a bit of post-processing to make it look finished. The Mounting Plate was cut from ¼ inch polycarbonate on a CNC router. The rest of the parts are…

Downloads
110
Likes
13
Rating
0
P
PrintablesPrint_It

SU HS2 Carburetor Velocity Stack

I created this velocity stack based on pictures I found online. It mates with a K&N air filter (model RU-4410 or RU-2990) There are left and right variations of the velocity stacks. I also added a flange at the end of the stack to the…

Downloads
95
Likes
13
Rating
0
P
PrintablesGaetano Lia

Laccio tappo carburante Audi A4

Laccio che tiene il tappo del carburante ancorato all'auto

Downloads
88
Likes
11
Rating
0
P
PrintablesPequ83

Yamaha XT600E Carburator Synchronization Tool

Yamaha XT600E Secondary carb butterfly valve needs 7mm opening in primary carburator slide prior to it's opening. This tool is to make synchronization adjustment easier. Just slide this tool under the carburator slide, obviously flat side…

Downloads
87
Likes
6
Rating
0
P
PrintablesBonwit

SU carburetor choke clip for Austin Healey Sprite or MG Midget

If you don't have a locking choke knob on your Austin Healey Sprite, or MG Midget, or other vintage car using this arrangement, you might be using a clothespin to hold the choke in position. This simple clip is slightly more elegant. One…

Downloads
83
Likes
7
Rating
0

4 Hole Carburetor Spacer 650-750 Holley and 750 Edelbrock

4 hole tapered and radiused carb spacer. Bores are for 650 to 750 Holley and 750 Edelbrock. Single plane intake all 4 holes intersect. Dual plane, only front to back holes intersect. PETG may be a bit too low temp depending on…

Downloads
79
Likes
14
Rating
0
P
PrintablesAK- V-2

Babetta 210 carburetor cover dellOrto

This Dell Orto carburetor cover allows direct connection to the original intake of the Babetta210 moped, after replacing the original Jikov carburetor. It can also be connected directly using the original connecting elastic tube. This…

Downloads
74
Likes
11
Rating
0
P
PrintablesThe_MF_Boss

Polaris SL 750 Bottom Carburetor Gasket

This is the gasket that goes on the bottom of the carbs where they mount up to the ski. I needed them and didn't want to wait for shipping. They are holding up really well so far. Must be printed in TPU. The part should be all bottom and…

Downloads
74
Likes
10
Rating
0
P
PrintablesKOMPOTKO

Choke part to carburetor for HONDA XRV 750

Choke part to carburetor for HONDA XRV 750 - 16046-MAY-000.

Downloads
73
Likes
2
Rating
0
P
Printablesdscarbro

Keihin PWK Carburetor Idle Adjuster Knob

Large knob to make adjusting the idle speed on Keihin carburetors possible without a screw driver. The knob presses onto the plastic knob supplied on the carburetor.

Downloads
69
Likes
6
Rating
0
P
PrintablesNX.Richi

Carburetor choke lever

My motorcycle choke lever broke, so I designed one, but better. I suggest printing it with 80% or more, to make it stronger. This model was made in Fusion 360, feel free to ask for a custom model.

Downloads
68
Likes
8
Rating
0
P
PrintablesLoosiu

Honda CN250 Helix carburetor service stand pack

The service stand and cup (for up side down position ) for Honda CN250 carburetor - KEIHIN VE. The main stand has slot in the base for convenient attachment and top clamp so the carburetor body can be hold in tilted position. The cup is…

Downloads
67
Likes
6
Rating
0
P
Printablesjmynheir

Ryobi(and other) Blower/Trimmer Carburetor Adjustment Knobs

These are knobs to slip on to the low and high fuel adjustment knobs to Ryobi(and others) Carburetor. I used a Ryobi R09050 blower for testing and fabrication. I also included the blend file that I created the peices so you can modify in…

Downloads
61
Likes
7
Rating
0
P
PrintablesCheeseBurger

Rochester MonoJet Carburetor Main Body Gasket

I printed this in TPU at .2 Layer height. It's been installed in the carb and working for more than 6 months as of this writing with no leaks or issues. Print this at your own risk, I made this because I was in a bind and needed a part…

Downloads
60
Likes
3
Rating
0
P

weber dellorto carburetor jet holder

weber/dellorto carburetor jets holder simple design but very useful to keep everything organised check my other project too im not a professional designer but im learning have a fun ;-)

Downloads
59
Likes
9
Rating
0
P
PrintablesHRC450

SU HS6 carburator velocity stack

Needed some velocity stacks to fit inside the airfilters of my Volvo The old airfilters are opened up and a wachable cartidge is sandwiched between the 2 covers with the stacks inside.

Downloads
57
Likes
3
Rating
0
P

MG MGB Air Filter Cover (SU-HIF4 Carburettors)

English Discription below! Diese Platten sind Plug&Play mit den originalen Cooper Cans tauschbar, es werden fasst alle Teile aus den originalen Luftfiltern verwendet. Die untere Aufnahme, der Dichtring, Distanzhülsen sowie Schrauben von…

Downloads
57
Likes
7
Rating
0
P
PrintablesMadMax7774

GP76 gas engine (with Walbro HDA-246 carburator) Carb Cover

This friction-fit carb cover prevents the prop wash from interfering with the mid-range breather hole on the Walbro HDA-246 Carburator of the GP76 RC gas engine. It helps to smooth out the midrange when tuning the engine. It was…

Downloads
56
Likes
1
Rating
0
P

Carburettor intake manifold

Motorcycle carburettor intake manifold

Downloads
55
Likes
5
Rating
0
P
PrintablesHejkal

Simson S51 Carburetor seal cutting jig

This is the simple cutting jig for carburetor BVF 16N1 rubber seal. 1. use cutting templeate to cut the inner shape 2. use the other parts to fix the rubber and cut the outer shape. Printed from PLA - 0,2mm

Downloads
55
Likes
9
Rating
4.5

Carburator jet container

Main and idle jet container, infinite expandable! I printed the containers from red TPU and the top and bottom out of PET-G. Both materials are resistant to fuel. Mainjet container is for 6mm hexagonal jets and the idle container is for…

Downloads
55
Likes
8
Rating
0
P
PrintablesMcJosep

UNIVERSAL CARBURETOR CHOKE KNOB – COLD START PULL KNOB FOR CARBURETORS

HIGH-VISIBILITY CARBURETOR CHOKE KNOB – PERFECT FOR COLD STARTS This 3D-printable carburetor choke knob is designed to replace missing or broken cold-start pull knobs used in carbureted engines. The knob provides a comfortable grip and…

Downloads
54
Likes
10
Rating
0
P
PrintablesCptAmerica

Nibbi Carburetor Choke Cable Adapter

Adapter I created to connect an existing choke cable to a Nibbi carburetor choke plunger. Print with ABS or other filament with high temperature threshold as this part will be exposed to heat. Probably wouldn't be a bad idea to wrap some…

Downloads
53
Likes
4
Rating
0
P
PrintablesGarage_Tinkerer

Enticer 340 TPU Carburetor Gasket (Rectangular Bowl)

A printable float bowl gasket for the Yamaha Enticer snowmobiles with a rectangular float bowl. I used Ninjatek Ninjaflex TPU (85A) I then covered the gasket with parchment paper and uses a clothes iron to smooth the top surface, This may…

Downloads
53
Likes
4
Rating
0
P
PrintablesSherlock_Ohms

Carburetor Idle Set Screw

Print with threads pointing upward and with layer height < 0.20mm so that the threads are finer Recommend > 3 perimeters No supports required Brim would be a good idea

Downloads
52
Likes
5
Rating
0
P
Printablesthe_eddie

Briggs Carburetor Gasket

Simple gasket for printing in TPU

Downloads
51
Likes
11
Rating
0
P
PrintablesDMT_ZA

Carburettor Choke Butterfly Shaft

Disclaimer: This model comes without any guarentee of fitness for use with your engine - use at your own risk of engine failure. Material : A word of caution first! For a permanent solution a strong, high-temperature filament with…

Downloads
49
Likes
2
Rating
0
P
PrintablesVTXtruder

Carburetor Float Gauge

Float gauge is designed for a Goldwing GL1100 but should work for any Keihin carbs of the same design. They were used on a lot of UJMs.

Downloads
48
Likes
4
Rating
0
P
PrintablesSandTigerNL

Honda st1100 1991 carburetor gasket

I printed this with prusaslicer, flexi setting for the filament. The 0.1mm detail works fine for me. No brim I have already installed them, if it doesn't work satisfactorily I will remove this. This is a test and I am not responsible if…

Downloads
47
Likes
9
Rating
0
P
PrintablesGabriel Z

GY6 4T Carburetor Bowl Gasket - TPU

Gasket for the carburetor bowl on a cheap 4T (4 stroke) GY6 engine. Made it wider than the original on some spots where the gasket had empty space in the carb bowl groove.

Downloads
46
Likes
9
Rating
0
P
PrintablesSkooter

Air Cleaner Backplate Gasket for CV Carburetor (Harley-Davidson)

This Backplate gasket is made specifically for CV carburetors and is used between an air cleaner or backing plate and the Carburetor. These should be replaced when installing a new air cleaner. Print in TPU, brother.

Downloads
46
Likes
8
Rating
0
P
PrintablesMBStudio

Carburator Airfilter Adapter

This is an adapter for a motorcycle airfilter. The airfilter we had was 35mm inner diameter and the new carburator had a 40mm outer diameter. So, I whipped up an adapter for this. You can customize it to your needs. Print Settings…

Downloads
43
Likes
7
Rating
0
P
Printablesrobwhi

Hitachi DCG-306 Carburetor gasket Datsun 120Y (B210) etc.

I needed a new float chamber gasket for my Datsun 120Y (B210). The previous one had deteriorated too much and it was hand cut anyway so it had tears and poor holes for various jets etc. This new gasket was made by scanning the carb on a…

Downloads
41
Likes
4
Rating
0
P
PrintablesPistonPin

Spacer to fit a PZ16 carburetor on a NSR50

I'm on and off tinkering on my NSR50 project bike. I want it to be as stock as possible, but original carburetors are surprisingly hard to come by (or ridiculously expensive), so as a temporary solution I designed this custom spacer to…

Downloads
40
Likes
6
Rating
0
P
Printablesrebeltaz

Carburetor Adapter Plate with Vacuum For Kohler SV600-3224

Carburetor Adapter Plate with Vacuum For Kohler SV600-3224 by RebelTaz I swapped engines on a Cub Cadet in my shop without thinking it through first. The original blown engine utilized a vacuum operated fuel pump because the tank was in…

Downloads
39
Likes
6
Rating
0
P
PrintablesG3ox

Gurtner PY carburetor float

Gurtner PY carburetor float used in a lot of 50cc mopeds. I designed this one for my Peugeot Ludix because my original carburetor float broke and a new one is rare and expensive Print flat on bed with supports all around with a 0.1 or…

Downloads
38
Likes
3
Rating
0
P
PrintablesJan

Carburettor float height gauge

Tool to set the height of carburettor floats in motorcycles

Downloads
38
Likes
2
Rating
0
P
PrintablesWilliamPondside

Intake manifold / carburetor gasket for Honda Z50 Monkey

What is that? Intake manifold / carburetor gasket #09 for Honda Z50 Monkey. Fits the original Honda 16100-165-924 carburetor. I printed mine in PETG and the other option in TPU. Both materials are equally suitable. When using TPU, no…

Downloads
36
Likes
5
Rating
0
P
PrintablesRocketJockey

Air Intake for Solex carburetor

This custom designed velocity stacks fit on vintage solex carburetors. The top part can be taken off in order to put in some kind of grid (I cut up some old sieve) to keep debries out of the intake manifold. A custom die to shape and cut…

Downloads
35
Likes
6
Rating
0
P
PrintablesNicolai clausen

DellOrto and Polini CP carburetor nozzle

I have made a nozzle for DellOrto and Polini CP carburetors Flange that offers possibilities With this flange you can easily mount the Polini CP, DellOrto or carburetor The flange is mounted on the nozzle and then the carburetor is put on…

Downloads
33
Likes
4
Rating
0
P
Printablessuyo6774

Scooter/Moped short carburetor inlet (KEIHIN CVK 18)

A short bellmouth/velocity stack intake for a 50cc scooter (a Piaggio Fly 50cc 4T in my case), has a 30 degree corner adapter to fit under the plastic trim piece to seal up nicely. I had to rejet the carburetor up about 4 points and it…

Downloads
32
Likes
4
Rating
0
P
Printablesmotorlavka

ML-120K — lightweight two-stroke gasoline aircraft carbureted engine (12 hp), manufactured by JSC “Motornaya Lavka”.

ML-120K — lightweight two-stroke gasoline aircraft carbureted engine (12 hp), manufactured by JSC “Motornaya Lavka”. Applications: • entry-level ultralight aircraft • small fixed-wing UAVs • motorgliders and experimental aircraft •…

Downloads
32
Likes
1
Rating
0

Motorcycle Carburetor Air Filter

Motorcycle carb air filter connection/housing/etc my carb has an inlet pipe thats 44mm I had done the voronoi skull first, worked well for years. I used a different skull i found online, just becuase it seemed to perhaps let less rain…

Downloads
32
Likes
11
Rating
0
P
PrintablesJan1926

carburetor spacers

carburetor spacers SZC 38 for pwk 34 lanza tpu

Downloads
31
Likes
5
Rating
0
P
PrintablesThtunew

1979 Honda CB650 Carburetor Choke Arm

Replacement 3D printable choke arm for 1979 Honda CB650 motorcycle

Downloads
31
Likes
3
Rating
0
P
PrintablesVictor Whittle

SU HS2/HS4 Carburater Float Bowl Gasket

Made this gasket from TPU as its fuel resistant and couldnt find a local replacement and couldnt wait for a replacement to be imported so i printed a new one , so far been holding well when used with a facet electric fuel pump ,

Downloads
30
Likes
4
Rating
0
P
PrintablesOndřej Merth

Carburetor Jet Holder

Assorted holder for different size M5 threaded carburetor jets.

Downloads
30
Likes
0
Rating
0
P
Printablesskidsolo

Honda GL1000 Carburetor inlet rubber

Print in FLEX 70 % infill does not have to be super flexible I used cheap Chinese flex from amazon. best printed with the location notch down.

Downloads
30
Likes
7
Rating
0
P
PrintablesFAIR

Těsnění plovákové komory karburátoru (vajíčko) Stadion S11 / S22 Gasket for the carburetor of stadion s11 / s22.

CZ Těsnění pro karburátor legendárního mopedu stadion s11 a s22. Tiskněte z TPU nebo jiného flexi materiálu (doporučuji otestovat zda se nerozpouští v benzínu). výplň 100% ENG Print out of TPU or other flexi material (I recommend testing…

Downloads
30
Likes
4
Rating
0
P
Printablesstephen collins

Rochester MonoJet Carburetor - Throttle Body Gasket

Main Body Gasket (Throttle Body Gasket in OEM Diagram) for the Rochester Monojet carburetor. There are other versions of this Gasket for different versions of the MonoJet Carb Family, but this one matched the chinese knockoff carb I…

Downloads
29
Likes
3
Rating
0
P
PrintablesVictor Whittle

SU HS4 Carburater Spacer and Gasket

a spacer template for SU HS4 Carburater , can be printed with exotic materials Or CNC , tested in PETG which did hold up but would reccomend use of PETG in emergency cases only , Lasted about a week before was totally warped Gasket also…

Downloads
28
Likes
2
Rating
0
P
PrintablesJan Kurek

Vacuum Carburetor Synchronizer

2 pcs screw M4 x 12 mm 2 pcs nut M4 nylon hose diameter 4 mm manometer https://www.aliexpress.com/item/4000297036291.html?spm=a2g0o.cart.0.0.3fbb3c00d37y3T&mp=1&fbclid=IwAR1Oem6KbuwMDH\_mbio5jrwT1NGR4HzC-9qfDTRg70S3GYcf-yJHQQGxxJY…

Downloads
28
Likes
6
Rating
0
P
PrintablesStefan Toczek

Nissan Terrano KA24E intake manifold adapter for weber 32/34 style carburetor

Nissan Terrano KA24E intake manifold adapter for weber 32/34 style carburettor - don't ask me why, here is the model Carb used - fiat 125p / fso polonez / zuk licensed weber 32/34 Print it with 100% infill, preferably with petg or some…

Downloads
26
Likes
1
Rating
0
P
PrintablesChristophe-P

carburetor gasket STIHL SR 420

pour remplacer le joint d'origine imprimé en TPU pour carburateur Walbro K10-HD n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir ! Bon print !

Downloads
26
Likes
2
Rating
0
P
Printablesfiferox

Joint carburateur peugeot fox

Joint carburateur pour peugeot fox qui se met sur la pipe original à faire en tpu

Downloads
26
Likes
3
Rating
0
P
PrintablesMariobrosk

serbatoio carburante

serbatoio carburante ricostruito per ricambio

Downloads
26
Likes
1
Rating
0
P
PrintablesRyan

Snow Blower Carburetor Adaptor

This is a carburetor adaptor for MTD engines which comes on a lot of Troy-Bilt and Craftsman snow blowers. This adaptor lets you test and tune the snow blower without the hassle of putting it all back together. Printed with PLA, 3 wall,…

Downloads
26
Likes
6
Rating
0

Seadoo Carburetor Cover Clip

Mostly exact copy of a Seadoo Speedster 1996 carburetor cover clip.

Downloads
25
Likes
0
Rating
0
P
Printableselbiondo93

Stand Carburatore Dell'Orto Vespa 50 16.16

Stand Supporto Carburatore Dell'Orto Vespa 50 16.16

Downloads
25
Likes
3
Rating
0
P
Printablescel

Multiple Carburetor Sync Tool

A PET Cap with a Boss and 3 Holes to make a simple but very accurate Carburetor Sync Tool, you only need 6mm (or ¼") clear Hoses and a PET Bottle for each Carburetor(throat). Insert 1 Hose in a Cap Hole from the Top until its flush or…

Downloads
24
Likes
1
Rating
0
P
PrintablesSB3DWorks

Replacement Carburetor Intake / Heat Dam Manifold for Homelite/Ryobi – Part #51892001

I Printed it without enclosure with Prusa MK4S Material: Fiberlogy Nylon PA12 Layer height: 0.2mm Perimeters: 8 Infill:100% Supports: Yes Draft shield: Enabled Brim width: 10mm Satin sheet Heatbed temp 110c Nozzle temp 265c Printing…

Downloads
23
Likes
4
Rating
0
P
PrintablesSzymonides11

Dnepr Dniepr MT 9 and up Air duct for Keihin PWK30 carburateur swap.

Air duct models for connecting PWK carburetors to the Dnepr OHV engine (650 cm³). Fits with the original gearbox (with reverse) and K750-style chimney. This setup removes the original pipes and choke system, with no need for a new one. It…

Downloads
23
Likes
1
Rating
0
P
Printablesmerlin699

carburetor caps for Solex PAITA

I designed caps for the carburetors of my spare engine of my BMW 3200 CS. Much better than covering them with some pieces of cloth. Fits also the Solex PAITA 32 from several Mercedes models. Best to be printed in TPU. Flip the model in…

Downloads
23
Likes
2
Rating
0
P
PrintablesNils Lindgren

Triumph TR6 Carburateur hose adaptor

Print at 100% density, at 100% scale.

Downloads
23
Likes
3
Rating
0
P
Printablesmotorlavka

ML-80K — compact two-stroke gasoline carbureted (optional fuel-injected) aircraft engine rated at 5.5 hp, manufactured by JSC “Motornaya Lavka”.

ML-80K — compact two-stroke gasoline carbureted (optional fuel-injected) aircraft engine rated at 5.5 hp, manufactured by JSC “Motornaya Lavka”. Description: • compact carbureted engine (fuel-injected version available) • designed for…

Downloads
22
Likes
0
Rating
0
P
PrintablesThe_MF_Boss

Polaris SL 750 Top Carburetor Intake Gasket

I needed to get the intake gaskets for a SL 750 and didn't want to spend the money on the gaskets since they aren't exposed to anything but air and mild heat. These need to be printed in TPU and should be all bottom and top layers with no…

Downloads
22
Likes
6
Rating
0
P
PrintablesKfry

Bear Cat WT190 Weed Trimmer Carburetor Gasket

What I Used: Polymaker TPU 95A Amazon Basics TPU setting If you wish to donate, it will help me with my journey to create more files for all of you Thank you : https://www.paypal.com/donate/?hosted_button_id=FRD499EASX35Y

Downloads
22
Likes
3
Rating
0
P
PrintablesChristophe-P

Seal carburetor Agria 2100

a imprimer en TPU seal N° 18 n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !

Downloads
20
Likes
0
Rating
0
P
PrintablesBM

Bing 54 carburetor plug cover

Printed with Tpu flat on the bed. Now with pull tabs

Downloads
19
Likes
2
Rating
0
P
Printablesk1n3k

Mikuni PHH 40 carburetor 3d scan

This is a 3d scan of a Mikuni PHH 40 dual barrel side draft carburetor. I believe the Weber side draft is also a direct drop in replacement as far as the flanges but don't quote me on that. This is one of two carburetors, and doesn't have…

Downloads
19
Likes
0
Rating
0
P
PrintablesFacundo

Carburettor Float For weber 32 34 DO 140% SCALING ON X and Y

Be mindful of the hydrocarbon tightness of the print! I went with nylon. it was a temporary experiment, do not know how much it will last! you tell me.

Downloads
19
Likes
1
Rating
0
P
Printablescull

Husqvarna 225R carburetor filter cover

Cover is secured by HEXM5 bolt with length about 25-30mm. Available is version with embedded Husquarna logo or without logo. Available is knob for securing filter cover. Might be also suitable for various Husquarna models.

Downloads
19
Likes
3
Rating
0
P
PrintablesMJDesigns

Carburetor Adapter

This is a simple 3D-printed adapter that allows you to fit a Honda XR100 carburetor onto a 2001–2003 XR80R while still using the stock XR80R intake boot. The XR100 carb provides improved throttle response and reduced bogging on the XR80R,…

Downloads
18
Likes
4
Rating
0
P
PrintablesMarionB

Carburateur testbak Mikuni HSR42

Dit hele object is zonder support geprint. De carburateur “hangt” in de bak dus je hebt de handen vrij. Dit object is gemaakt in Tinkercad.

Downloads
18
Likes
4
Rating
0
P
Printablesfisherbt

Classic Mini SU Carburetor Needle Marking Plate

This plate will hold an SU carburetor needle in a repeatable position so that you can mark the stations for polishing/modification. The needles vary in length, so yours may not go to the bottom of the plate and the number of stations used…

Downloads
18
Likes
1
Rating
0
P
PrintablesChad Stokes

Honda Carburetor Float Bowl Gasket - Honda CB175 / CL175 / CB200

This gasket can be printed in TPU with the following settings. It is a direct replacement to a factory seal and has worked perfectly on my own personal 1971 Honda CL175 Scrambler Print speed - 30mm/s Cooling - first layer only Nozzle Temp…

Downloads
17
Likes
3
Rating
0
P
Printablestorch

Carburetor bank jig

A simple fixture to hold a bank of carburetors during bench service. The stl's are sized to hold a Yamaha XJ 750 / 650 carb bank but I have included the parametric FreeCad files so they can be customized to suit any similar bank (to…

Downloads
16
Likes
3
Rating
0
P
Printablesdreiser

Adapter for the RZ30 carburetor

printing from PETG plastic or ABS

Downloads
16
Likes
1
Rating
0
P
PrintablesDIYdie

Earthquake M43 Carburetor Diaphragm

I accidently put a hole into the carburetor's diaphragm on my tiller when putting a new primer bulb on. I didn't realize until the engine kept flooding. So I went to Fusion360 to see if I could make a temporary diaphragm by tracing the…

Downloads
16
Likes
1
Rating
0