Counting matching models…
ENGLISH … I want to share with you a 1:10 scale body model of the Land Rover 3 Series (III). The wheelbase is 229-230 mm. Body width 170mm. The front fenders, doors and rear fenders are connected using 3 pieces of carbon rods with a…
This design is based on spacing points as equally as possible on a sphere (using charge-like relaxation optimization) and then cutting planar slices perpendicular to those directions. This make fairest as possible dice for any number…
The VOID9 Macropad is a handwired 3x3 pad that uses a Pro Micro as a controller. Two versions for the top case are included, one of them is flat, the other has a 4mm fillet. There are two versions for the bottom case as well, a flat one,…
MN90/99 D90 Rear Roll Bar with and without tire carrier. You'll need to get quite a bit of support for this to all work; but it turned out really well. Both options are included in the file. You'll need 2 x M2 15mm or better to hold the…
A simple knob replacement for the Philips HD9200 Airfryer. Designed to fit the timer knob, but I think it would also fit the temperature knob. I used a sharpie to put marks at the 10-minute intervals. With the knob installed, the 0-minute…
Sleeve for extended XD9 magazines. Designed to fit AWCY?'s XD9. Tab'd version has a removal tab on the back to help with printing the sloped edge.
This model is inspired by the babyphone mount by Bosal. A solution to mount the babyphone of a friend at bed. I created the part from scratch to add the following features: The edge of the bed is 20.5mm wide: easy… Screwing the M6 without…
I had this second hand gas heater, the Truma E2400, but this part was missing and it appears to be smaller in diameter than the spare parts you can buy …. So I designed one (from pictures & measurement of the parts you screw it on) and…
As often in cheap crawler kits, the required steering parts for a proportional servo are not included. The suspension could be better as well. Ans of course, some tuning parts are always nice. So this thing includes: Servo clamp Improved…
WIP - MN90 D90 Front Battery Expansion ("frunk"). The stock part doesn't allow for any good size battery or after market electronics. So I created a set of 3 parts to make it all work. All holes (minus the M3 hole) are sized at 1.95mm so…
Designed for 0.1mm layer height (0.2mm first layer height is fine). No supports required. Use 1mm thick double-sided tape pieces UPDATE: added BSP D9 version with +0.4mm clearance
The ribs on the circumference make the knobs less slippery. The original knobs are easy to remove. Help with a spatula. The steel leaf springs of the original knobs must also be used in the printed knobs. Fit the knobs so that the leaf…
THERE IS MORE TO COME - photos and instructions. NOTE: I accidentally included some redundant files: "Body A", "Body B" and "Body C" are identical to "Long Hood Section A", "Long Hood Section B" and "Long Hood Section C". All I did was…
Germany’s Next Topmodel 1941 and Luftwaffe's best workhorse. My favourite German WW2 fighterplane. Designed by Kurt Tank. Use Paperclips for the struts. https://en.wikipedia.org/wiki/Focke-Wulf_Fw_190 3D-Dora Model:…
MN90/99 front chassis plate upgrade. No mods to the stock chassis rails are needed. Uses only 11 grams of plastic when printed at 0.2 and 20% infill. The stock screws for mounting the body can be used. This chassis plate requires a 17g or…
MN90/99 rear chassis plate upgrade. Uses 4 x M3 screws (8mm or 10mm will work). No mods to the stock chassis rails are needed. Uses only 11.4 grams of plastic when printed at 0.2 and 15% infill. The stock screws into the body posts…
die hinteren Fender angepasst. the rear fenders adjusted.
***Had to name it in this wierd way, because Glock is very protective of its name. I should've expected this beforehand, the biggest producer of ...."Horse milk".... will be a bit awkward when its about reading his own name. "Big Stick" -…
General Description Most parts marked L and R for left and right. LR parts fit or must fit both sides. However, some parts need to be mirrored in the slicer. Almost all holes are designed for M3 screws. Sometimes nuts are needed, but…
These 3D printable files are designed specifically for storing bobbins from the Janome HD9 v.2 . The bobbins for this machine are larger than standard household machine bobbins. (Edit: There was a small mistake in the first version of the…
Mount for side protectors for honda crx ed9/ee8 Reverse engineered from (probably) orginal mounts in side mounts for front fender. It work quite well in my case Dont look at print quality of my version - i had quite wet filament at that…
Reinforcement and Wheelholder for Tamiya Land Rover Defender D90. Replaces the polycarbonat pieces “rear brace A” and “rear brace B” (instructions page 15, step 30). Drill holes and use double-sided tape as described in the instructions.…
The diameter of the retaining circle is 70.82mm. The fixing holes are 5mm. In the photos I fixed the support temporarily with Patafix / Blu-Tack Print in PLA, 0,15mm, with support
These are designed to replace the unobtainable MD998761 special service tools to install the camshaft oil seals for a 6G72 (Mitsubishi 3000GT, Dodge Stealth, etc…) Specifically designed from measurements taken off of original,…
Babyphone Halterung Philips Avent 2-Teilig mit einstellbarem Winkel. Zusatzmaterial: M6x25 (Innensechskant) / M6-Mutter Die Klemmplatte hat eine Aussparung von 17mm, kann nach belieben angepasst werden.
Rear Magnetic Body Mount kit with option for an extra enforcement. Allows for the rear body mounts to be magnetic only or use the stock screws into the existing supports. Does require you remove (if present) the one extra stand-off on the…
This is an enclosure for a Waveform / Signal Generator built with an Arduino Pro Mini or Nano (ATmega 168 is sufficient) and an AD9833 Programmable Waveform Generator. One 18650 Battery can be fitted inside the case together with charging…
Ipad9 TouchChat word power 60 PureSense Case keyguard attaches with micro sucation tape
Description D9 Arrow is a slim 3D printed model rocket designed around D-class model rocket motors, with a focus on stable flight, clean aerodynamics and simple assembly. The rocket has been designed and simulated in OpenRocket , with the…
I have recreated the beautiful Porsche Design90 rims, also known as D90, for the modification of the low poly Porsche 991 Turbo. These fit the V2.1 tyres of the remix and are installed in the same way. Porsche Model:…
I made this so I can use the printable Miele tools on my Electrolux Pure D9 which has a non-standard shape. Adapter fits over the Electrolux hose and under the Miele tools. Miele tools: https://www.thingiverse.com/miele_3d4u/designs
VERSION 4 now!! - Custom Cooling duct for Wanhao Duplicator D9. Cleaned up the design, lowered the duct holes below nozzle Working perfectly well compared to stock.. Please post the feedback how you liked it or if any improvements. NOTE:…
This model is the bezel for this beautiful monitor. it's really hard to find original one and could be quite expensive.
Here's the result of uncountable iterations of trying to improve the part-cooling fan that comes with the Wanhao Duplicator D9 (MKII 400). It's supposed to fit the original 4010 fan without the need of disassembling anything. Just use 2x…
Für den CRX ED9 habe ich einen Halter für die Sonnenblende entworfen. hab ihn mit TPU gedruckt und 25% Füllung. Nach dem Druck ist noch etwas an Nachbearbeitung notwendig da die TPU Stützen recht bescheiden zum wegmachen sin und die…
Credits MirageC Initial work and for designing this awsome Printer
Additional Parts needed 1x Bahar Enclosure 150*140*70mm project box 1x C-Control Pro Nr. 197220 SD card module 1x MeanWell RS-15-5 PSU 1x CBM D9069 PetSD+ variant board ( https://github.com/InsaneDruid/CBM-D9096/ ) 2x 5mm LED (one red,…
Maytag Oven Knob labeled "KIP 5D94" on the back. Files include the original scan and a CAD model in STL. These are visually indistinguishable from each other when printed. These were created for someone else, so I haven't had the chance…
Using the SCAD file from the original , I expanded the AAA and AA columns. Can hold the following battery types and quantities: AAA: 56 AA: 40 C: 6 D: 5 9V: 6 Print Settings Printer Brand: Creality Printer: Ender 5 Plus Rafts: No…
This is the ROCKET CANDY model, a rocket designed for experimenting with and learning about aerospace propulsion. This model is specifically sized to be powered by: A D9-5 type black powder motor. Or DIY solid propellant (Rocket Candy…
When travelling, it was hard to find a place to put this camera, with a view from above the bed. So here is a camera mount to be fixed on the bed. You need a piece of wood, and some M4 screws and nuts. Once assembled, you can mount the…
I was trrying to found some models that would fit my car well but i didnt find any so i made my self one i am using 12V 10mm wide led stripe and some m3 screws for mounting I printed it in PLA but i would say you can print it with any…
I built the remix of Void's 3x3 macropad - the Void9 - which is here (https://www.thingiverse.com/thing:4816077) on thingiverse. The dimensions for the remix and Void's original are, so far as I can tell, the same so this model should…
Uploaded at the request of an inquisitive redditor, this 9 sided polyhedron is created with the intended use as a basis for a 9 sided die. This die has not yet been tested for fairness, and there is no mathematical proof of fairness, so I…
Dies ist eine Abdeckung für die Handbetätigung vom Schiebedach am ED9, Habe diese mit Carbon- PETG gedruckt mit 25% Füllung und 3 Lagen Wandstärke. Passt super und lässt sich problemsos auch wieder abnehmen. This is a cover for the manual…
Ender 3 base with the Philip Avent SCD923/26 lock mechanism connected with a printed bolt. Bolt should be printed with 100% infill,
Y Reduzierverteiler 1x 98 auf 2x76mm AD 1x in 2mm Wandstärke/1x in 3mm Wandstärke Y Reducing manifold 1x 98 to 2x76mm OD 1x in 2mm wall thickness/1x in 3mm wall thickness
Potřeboval jsem někam umístit jeden 5.65" displej, tak jsem pro něj vytvořil jednoduchý rámeček podobný tomu, co mám pro 4.2" modely. Seznam součástek: Good Display GDEP0565D90 5.65" 600x448 LaskaKit ESPink ESP32 e-Paper LaskaKit SHT40…
Engine bay for MN D90 with space for two 18650 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: Toys & Games
LATEST version 3 - Uploaded here: https://www.thingiverse.com/thing:4212688 Custom Cooling duct for Wanhao Duplicator D9. Working well compared to stock.. working on next version for blower fan which shall improve this more.. Please post…
The battery door latch for the D50 D70 D70S D80 D90 D100 cameras can break causing the door to not properly latch shut. This is a 3D printable replacement part for the latch. Print Settings and Recommendations: 0.2mm Layer Height 100%…
Wanhao Dupliator9 MKII Bauteillüfter. Remix, von Grund auf neu gezeichnet in Fusion 360 Der Flansch ist für einen 50mmx50mmx15mm Radiallüfter Print Settings Printer Brand: Wanhao Printer: Duplicator9 Rafts: No Supports: Yes Infill: 32%…
Tested with this DC to DC converter: https://de.aliexpress.com/item/32833258033.html
Print with strong material. No PLA. PET and Nylon worked best. Design is made for Lizard95 with VTX02 VTX03 and a Runcam Micro (19mm or similar micro cam) Category: R/C Vehicles
added braces to allow the spool holder to be mounted to the 4040 profile on the wanhao Duplicator 9 added 5mm holes to make sure the pieces are held together as they are floating more than originally intended and added 5mm holes to the…
Replacement gearset for the Office DEPOT HD95 laminator. You'll need to print 2 of the roller gears to have a complete set. Remember that it's HOT where these things live, so use an appropriate material; I used PA-6 Nylon. (6 Walls, 30%…
this shroud is based on the rogue SD shroud. so it uses the same barrels. but I found that with short shrouds like this it's quite east to place your hand in the wrong place. so in case you like the look of a P90 ish style grip more then…
Update 7/2/2025: The device firmware is complete with a v1.0 release, creating the user experience of ever-appearing CW stations as you turn the tuning knob. https://github.com/jhogsett/FluxTune/releases/tag/v1.0.0 Update 6/27/2025: There…
A couple of cases for the RFD900-UX so that you don't have stuff dangling around. Bonus cover included that I wasted time on trying to figure out how I could Light Pipe out the LED's... but one is behind the metal, so it's a big hassle. I…
Dies ist eine Zugentlastung für den Wanhao Duplicator 9. Diese kann nur montiert werden, wenn der Extruder so angebaut ist, wie man in den Bildern sehen kann! Man braucht zur Montage folgende Sachen: 2x Schraube M3x12 + Unterlegscheibe 2x…
This is a protective cover for the NASTY D9Ki 9000 Puff Vape. Has all the necessary holes for airflow, charging and display. Has a lot of available area for customization like names or logos. Preferably you should print in PETG or…
https://www.3djake.it/bigtreetech/dc-dc-stepdown-module
Two colour MI Band 9 stand. PLA printed, some supports needed.
Lizard95 flexible Akkuunterlage mit Rillen, damit der Akku nicht rutscht Lizard95 flexible battery pad with grooves, so that the battery does not slip Category: R/C Vehicles
i don't want to change it every time i crash so i design a beef up one Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100 Category: R/C Vehicles
https://it.aliexpress.com/item/1005004569914022.html?spm=a2g0o.order_list.order_list_main.137.21ef3696lhiffB&gatewayAdapt=glo2ita…
This is a simple lens hood I designed for the Sony Mavica MVC-FD91, they really have a way with names don't they? Sarcasm aside, I really enjoy shooting with this camera, but don't like how the lens can get very overwhelmed when shooting…
The Zastone D9000 radio comes with a handheld microphone connected to the radio with an RJ45 cable. This is a desktop microphone that uses the PCB from the original microphone. There are two buttons, left and right, but only one of them…
Cheapo Well D90 full auto airsoft, fires when BB's get to the hopper. as standard this requires a lof of shaking in the air, dry fires are common. Reducing size of Mag and keeping BB's at rear improves feeding, makes gun more reliable,…
Small stand for a Cessna MD90 Clock. I painted mine glossy black, a barrel jack is used in the back for power, and wires are run through the base and legs.
updated -add hole for fc's screw replace that two stupid standoffs that try to puncture the battery every time i crash Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: 0.2 Infill: 30…
Two extension tubes that are 14 mm wide at the tip. One has side holes and is intended to be used for couches. The extensions and connector are 200 mm long. Print them standing. I used paint on supports to stabilize the print since they…
antenna mount is harder to break thicker vtx plate mean less deform from vtx's heat Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100 Category: R/C Vehicles
The Philips HD9280 is a nice air-fryer, but it has, in my opinion, a single stupid design fault: In bright light it is impossible to see where the touch-keys are located as the brightness of the light in these keys, are very very low. To…
Ersatz für Amazone GE182 UF Pflanzenschutzspritzen T-Stück mit 1 1/2" Gewinde gedruckt in PETG 100% Ein schneller Ersatz bis das richtige Ersatzteil da ist, aber die Maschine nicht stehen darf
Replacement cover ring for SCD953/26. Download all the other parts from the original. AI was used to remove text and remix to fit smaller and taller newer model of phillips avent. I used PLA, 0.2mm layer height and 15% infill.
You'll need to replace black rubber thing with the printed one
It is expensive to try to purchase the rotating brush for the slightly older robot vacuum cleaner dibea d960. So, I created a holder to reuse broken brushes. If you don’t have a broken brush, I think you can buy a brush from another…
Compact cover with flexible cableguide to reduce strain on the cable. It is recommended to use a cable tie for strain relief and to cover the cableguide together with part of the cable with shrinking tube. Best fitting screws are M3x12mm…
A rear driveshaft for the FCX24M. I used a 4mm nozzle and PLA
Need some headset spacers for your new X-Lab? Here they are. Check out my other model that is a X-Lab spacer to a round stem with a cable exit. If you would like to be able to sell these in a personal use setting (ex: you work in a shop,…
THERE IS MORE TO COME - photos and instructions. NOTE: I accidentally included some redundant files: "Body A", "Body B" and "Body C" are identical to "Long Hood Section A", "Long Hood Section B" and "Long Hood Section C". All I did was…
A couple of cases for the RFD900-UX so that you don't have stuff dangling around. Bonus cover included that I wasted time on trying to figure out how I could Light Pipe out the LED's... but one is behind the metal, so it's a big hassle. I…
It is expensive to try to purchase the rotating brush for the slightly older robot vacuum cleaner dibea d960. So, I created a holder to reuse broken brushes. If you don’t have a broken brush, I think you can buy a brush from another…
Designed with precision and purpose in mind, tested for 5 years this adapter allows you to mount your drill to a wall or counter fits in like a hoist and it is tight fit once in place perfect for transport and quick use. For best results…
General Description Most parts marked L and R for left and right. LR parts fit or must fit both sides. However, some parts need to be mirrored in the slicer. Almost all holes are designed for M3 screws. Sometimes nuts are needed, but…
Cheapo Well D90 full auto airsoft, fires when BB's get to the hopper. as standard this requires a lof of shaking in the air, dry fires are common. Reducing size of Mag and keeping BB's at rear improves feeding, makes gun more reliable,…
If you want to get this template without subscribing, write me in chat! - SideSilhouette
Headboard mount holder for a ThundeaL TD93Pro projector or other appropriate. initially, the mount is straight, if you need an angle, an additional angle expander is attached, you can also download the project and convert it to Fusion360
First of all, thank you eglobetrotter for your awesome design! I remixed his work to fit the new Philips Avent Connected SCD921/26 camera. I printed everything (in Prusament PETG Urban Grey - PLA is fine) with 3 perimeters on my Prusa i3…
I wanted to combine various parts I had into a useful device for creating sound effects. This uses two Arduino Nanos, three AD9883 signal generators, three rotary encodes, a 20x4 LCD display, and various other components to produce sounds…
I needed more desk space and thought of mounting topping D90 stack under the table like @lucasratmundo posted here https://www.thingiverse.com/thing:4731244 but his design needs a bigger printer and couldn't print it on Mk3s. So, i…
With this K1 exhaust fitting you can get your printer quite a near to wall and still get D90 exhaust hose out from it. I made this part on two pieces, because for easier printing. Just tape pieces together with ductape after printing, In…
Took my JetBD920 fan blade cover off to clean out any chips and found a broken blade. The whole fan was just rotten plastic. This is the replacement I drew up in Fusion360 Category: Machine Tools
Well I finally looked first for these gears in Thingiverse instead of blasting away and drawing them myself. Unfortunately no one has seen the need so here I go. A link to the Fusion360 project is here / https://a360.co/2MmJPNo I needed…
