Counting matching models…
Use case This screwdriver (bit holder) is made for fine to medium duty work. It is made to fit well into the palm of your hand, while still giving you a good grip for your fingers to apply some reasonable torque. Thanks to the clamping…
If you want to print it in a multi-color format, my colleague made a remix. https://www.thingiverse.com/thing:5174825
These are various parts for the EEW Cone Winder . There are some Fusion 360 files which allow you to generate cones or tubes of different sizes. Below is a video that goes into depth about how those works.
A minimalist 3D-printed photo holder shaped like a flowing Christmas tree silhouette. Its smooth wave design elegantly supports your favorite memories, blending festive charm with modern décor. Perfect for displaying Polaroids or small…
For parts like the nacelles just mirror the parts in your slicer to get both sides. Hardware used: -Matek H743 Wlite -Matek m8n gps -Iflight Xing2 1806 2500kv motors -Corona DS939MG servos on tilt, Racestar DS5601MG servo on elevator…
This lets you print parts for your EEW Nano 2. Here is a video with more info about how the parts are used. The only file that should needs supports is nano2_bobbin_disk.stl. For more info about my fiber tools visit:…
I have released a different version of this bobbin that prints in 4 parts instead of 3. However, by breaking this into 4 pieces it requires less supports and the final print is nicer. BobbinDisk 2 and BobbinTube do not require supports.…
UPDATED 2025-05-12: I was cleaning my bicycle's cassette and pushed a little too hard, and near the tip of the tool, two teeth in from the tip, the tool broke and bent up. So, I redesigned these to have a little more material between the…
Cockpit Kit: Freewing Models R/C 90mm EDF F-18c Hornet This is a 1/11th scale cockpit kit designed for the 90mm EDF Freewing F-18C Hornet Fighter Jet. Included are the STL Files, a printed parts list, detail photos for painting, assembly…
This is a bike Freewheel (not cassette) remove tool. Be aware that the Freewheel is mounted with high torque and the plastic tool may not hold up.
Printable Replacement Motor Mounts for the Heewing Ranger T1. Credit to @AlexSalut. These are really nicely designed replacements for the stock motor mounts that will allow some larger motors. I'm using T-Motor F1507s in the attached…
This is a new orifice hook design I'm trying out that clips into the side of the EEW 6.0, but it could be using with other spinning wheels. Normally orifice hooks are metal, but I found the flexibility of this plastic is nice. For more…
NEW AND BETTER DESIGN https://www.printables.com/model/649545-heewing-t1-vtol-for-gdw425mg-servo-and-emax-2210-m vtol parts for the ranger. designed specifically for emax es08maii servos. printed in petg recommend to print nacelles nose…
This is a list of the best 3D printable files I've made for the EEW Nano 2.1. You can get more information about this eSpinner at Dreaming Robots . Files starting with “eewNano21” will only work with the EEW Nano 2.1 Files starting with…
This is a replacement for the original T1 Ranger VTOL/FW top latch that I found to be quite fragile and easily broke after only a few actuations. This latch functions in an identical manner to the original with it being securely held in…
plate with holes for mounting fc in airplace
This is an accessory part for the Heewing Ranger T1. This model should protect the control horns and servo linkages during belly landings. I sized it to fit right up against the servo arm slot and protect most of the exposed linkage. I…
A simple wall hook to guide the CPAP tube above your pillow. Inspired by the model https://www.printables.com/cs/model/149491-cpap-hook The hook is on a tube with a diameter of 22 mm. It also has a mask hook when not in use. Printing on…
FULL CREDIT & Thank you to all the OG designers for the original designs. Great work. ALL Parts have been Remixed for my personal T1. Wanted to share my favs in one spot. Parts will be added and/or edited as the build continues. Stay…
These are many of the plastic parts for the EEW Fold. The EEW Fold is made from injection molded parts so these will be different if 3D printed, but these parts have all been tested and should work. You can use these to make more bobbins,…
You should print 6 of the disks, 3 of the tubes, and 4 of the plugs. Then assemble them onto an EEW 6.x bobbin. The plugs get inserted to hold these from spinning on the bobbin. Then you can spin small amounts of different singles onto a…
I'm releasing new parts for the EEW 6.1. This includes an updated bottom, the new arm support, and some yarn guides. There are a bunch of other files I've already released that are compatible with the EEW 6.1. Below are a list of those.…
This is a bobbin for the EEW Nano 1.x. This lets you print your own bobbins for this electric spinning wheel in any color you want. You can purchase this eSpinner at Dreaming Robots . You need to print 1x eew_mini2_bobbin_tube and 2x…
A wall hanger for the Heewing Ranger T1. Hang your Ranger by the fuselage on the wall.
The latest mods from Ellie Valkyrie's garage! GUNS GUNS GUNS! More guns than any Freeway Flier can shake a stick at! Requires supports. If you like my work and want to see (and print) more of it, please consider stopping over at my online…
This holds a your EEW 6.x (EEW 6.0 or EEW 6.1) to a tripod. You need to provide a standard hex nut and then glue that in place. Tripods use ¼ inch 20 threads. For more information about my fiber tools visit: https://www.dreamingrobots.com/
This is a lace weight flyer, which lets you spin at higher speeds. This can be useful for high twist lace yarn. I designed these parts so no supports are needed. Here is more info on the EEW 6.0: https://www.dreamingrobots.com/
A grid or honeycomb can be fitted over a light source to help control the spill of the light it produces. They look like bees' honeycomb (hence being known as honeycomb grids) and are great for helping to make a beam of light that is soft…
I originally printed the source model but didn't have a 30mm socket to use with it. I had to resort to using a adjustable crescent wrench. Unfortunately the wrench just slipped as the plastic was elongating out the open end of the wrench.…
There's now a Facebook group to discuss builds, successes and problems. Come join at https://www.facebook.com/groups/vtolhangout July 18 2022 update: Added a new nacelle design that is a bit longer for better airflow beneath the prop. It…
These are the parts needed to print a bobbin winder attachment for the EEW 6.0. Normally the EEW 6.0 spins fiber into yarn. However, if you remove the flyer and use this bobbin winder it allows you to quickly wind bobbins. The only parts…
This is an alternative hook option for the EEW 6.0 eSpinner. For more fiber tools see our store at: www.dreamingrobots.com
The placement tool lets you setup of the EEW Cone Winder much faster. The adjustable cone holder lets you try other cone sizes. This video shows you how these parts work.
This video goes into more details about how these items are used. The Yarn Parker is device that clips onto the front of the EEW 6 eSpinner and helps hold yarn. The Slitted Reducer goes on the front as another option to park yarn…
The Purr Protector is a case that goes around your EEW 6.1 (or EEW 6.0) so you can spin yarn even if your cats want to play. Visit my website for more information about my eSpinners: https://www.dreamingrobots.com/ You need to print with…
This cone is a bit shorter than the original and has better ventilation. I found the original STL was a bit long and tended to rub on the winder arms. The cone should be printed using a fuzzy outer skin setting, as it helps to better hold…
Replacement nose for the Heewing T2 Cruza. I wanted more air for my VTX and this is what I came up with. It's a little heavier than the foam nose of course. Depending on how you plan to set it up the minimum hardware you'll need are 4 -…
Nose for Heewing T2 Cruza specifically designed for the CADDX GM3 and HEQ (WIP) 3-axis gimbals. The nose is shorter than original so new fuselage mounts are needed. I've made extensions so the original can still be mounted. A custom…
This part locks the suctions cups in place so they don't accidently come off. This video shows how to use this part. The EEW Nano 2 is available here: https://www.dreamingrobots.com/product/eew-nano/
Antena is fixed with two zip ties. There are two additional paths for zip ties to ensure stronger fixation of the holder to the tail boom if needed. Printing parameters: Filamet: TPU Resolution: 0,2 Infill: 100% Supports: yes
Simple yet effective and secure tailboom antenna mount for T-antennas like the TBS Immortal T. Printed in PETG which is more flexible and durable than PLA. If you like my designs please consider donating a coffee or any amount really, I…
A snoot is basically a tube that goes over the front of your light/flash unit and creates a hard, concentrated beam of light. A snoot allows you to light your main subject – without lighting the surrounding scene. And this can be great…
These coil yarn guides clip into the metal hooks. These are useful when spinning coil yarn which can get caught on the metal hooks and should help with any other non-uniform bulky yarn that gets stuck on the metal hooks. Here is a video…
updated version changes: -servos changed to GDW DS 041MG -arms beefed up -motor plate has tab for zipting motor wires to. -m2 hardware for fastening nacelles halves together. Needed: m2 screw kit from amazon 2x 4x10x4 flanged bearing 2x…
When printing the nose i laid it on it's back. Uses a lot of support but it makes for a smoother looking print. I imagine someone can cutoff the cape type thing i have on the nose to make the transition to the fuse a little smoother. Up…
This holds a your EEW Nano (EEW Nano 1.0, EEW Nano 1.1, EEW Nano 2.0, EEW Nano 2.1) to a tripod. You need to provide a standard hex nut and glue that in place. Tripods use ¼ inch 20 threads. For more information about my fiber tools…
This bracket fixes the extended nose wheel in an AvantiS RC model from freewing. It stabilizes the landing gear. The component is hollow inside and has an edge to glue. The distance of the bracket between nose wheel and model is 15mm and…
Requires extended camera cable - 300mm
These are Celtic knot bobbin ends for the 3d printer friendly bobbin designed by Maurice for the EEW 6. These are the same designs as on my nano bobbins, but sized up and put on the bobbin ends for the EEW6 from Maurice's printable…
Okay this is pretty simple, I had the hatch fly off on my ranger, luckily it was on launch. I decided that I was not overly enthused with the clip nature of the original system. I printed at .1mm height. I used organic supports to support…
‘StarBurst’ design bobbin for the Electric EEL Wheel 6.x. Requires 2x R6 style bearings in front cap and rear Only tension end requires supports. Shaft designed to screw threads together to prevent need for supports. Used slicer to ‘cut'…
Here is another nose for the T2. This one is for the HEQ G-Port gimbal. This is the Walksnail version. I did include STEP and Fusion360 files if someone wants to change it for the DJI version. I went back and forth on an underslung mount…
Nose landing gear doors for Freewing Avanti S 80mm EDF. Haven't tried printed it yet. Would like to hear your print experience, successes, failures, slice & print set-ups, tweaks/ remixes, improvements, etc. Category: R/C Vehicles
This quill is designed to work with the EEW Nano 1.0 and EEW Nano 1.1. It gives you another method of spinning yarn on these spinning wheels. There is a video that shows how this quill is used at:…
Light Modifier - Fits the Neewer RGB61 RGB Video Light. USE M3x25 mm PRINT INSTRUCTIONS: Print with supports for the bottom
Bit screw driver with print-in-place freewheel that uses a 3x3mm tubular neodymium magnet to hold the bit in place. There is an option for half length and normal length bits.
I wanted to make a soldering microscope that is freely positionable over the work. So I modded my generic digital microscope with 35 mm tube. You need 2x(M4 nuts and bolts) and might use some washers for ideal spacing. Please print with…
Important: Please load latest version, project is still in progress. Wichtig: Bitte die aktuellen Dateien laden, da das Modell immer noch in der Entwicklung ist. Beim Modell handelt es sich um die Weiterentwicklung und Überarbeitung…
Basic way to hang a Heewing T1 Ranger on a wall, rests on the horizontal stabilizer, and uses a Command strip to attach securely to the wall without any damage. Included in the photos is the intended strip. Recommend printing at higher…
Heewing Ranger T1 Rear Outlet for better airflow
Light grid with customizable pattern and density. By making use of the infill pattern trick (0 bottom and top layers) you can choose which pattern to use for the light grid. And how many channels it should have. Modifying the openscad…
A case for the DSO154Pro oscilloscope which removes the base to have a salvaged one use e-cig circular battery (~ 12.9mm) to be secured at the bottom. It reuse the original screws. Also added a bit of a lip to protect the screen.
This is a modified design for Raspberry Pi 4 with Geeworm X703 Thanks for AiakosK https://www.thingiverse.com/thing:667
This is a mount conversion kit (or replacement) for affordable APS-C / MFT all-metal manual focus 35mm f/1.7 (or f/1.6 depending on marketing labels) prime lenses that are branded Neewer, Meike, and Jaray (there are probably others -…
Wing Fence for Freewing Avanti S EDF RC Jet I have printed in PETG and is flexible and does not break A file for milling is also included
Three variants for T-antenna mounts for the Heewing T2. One for the boom and for glueing to the side behind the wing. I made one variant to sit higher up so it can fit inside the Heewing T2 carrying case. The two foam mounts can probably…
Modified the part to fit the walksnail avatar hd camera.
Mount for DJI o3 Camera. Needs four M2 Brass Inserts. Base Plate gets glued into the plane.
This is a direct replacement front hatch clip for the T1. Features: Can be used to check CG like the original Light weight and Aerodynamic Note: The back plate is not included—and not required. In my experience with this and the original,…
grill for cool ventilation (get it?) i hot glued it in.
[edit] I have added a V2 which is lighter, but more importantly, allows a lot more breathability on the bottom, where the Air Unit gets hottest. I will be added a vent just below this spot (in the belly camera mount position) to bring…
Made two mount plates, one flat and one with slots for landing skids/wheels. The landing legs have 2.5mm hole which I tap to M3 thread and use a M3x8mm screw. A rubber band is used to angle the skids up ~15 degrees during flight. The rear…
I made these models to replace the plywood parts that come with the HeeWing T2. The VTX fan mount uses M2x12 screws to mount it together with a Walksnail VTX for a nice and sturdy package. The battery plate is made for 4S2P li-ion…
This is a remix modified to let pass a 17mm nut Category: Tools
i recommend umagrip or similar for securing the battery along with a velcro strap.
Designed to be compatible with the 16-19T freewheels by DNP. Probably also compatible with BLB Superior freewheels, as they seem to be the same product, but re-branded. 30mm hex wrench faces. Suggested to print with 100% infill, as the…
You need O-rings ID33x2,5 mm, ball bearing MR 128 8x12x2,5 and MR 128 8x12x3,5 ZZ. A servo: MASTER Servo S308. The Cam may need to be adjusted in size for optimal balance between brake force and the torque of the servo. The servo isn't…
This tray holds an F411-WTE (the replacement for the WSE, since the mpu6000 is no more) with mounts for the rails in the fuselage of a HeeWing t1 Ranger. Mine is mounted as far back in the plane as possible, which allowed me to also fit a…
This is a case for the EEW Yarn Counter. It can be printed without any supports. Here is a video that gives more information about this case: https://www.youtube.com/watch?v=WjhCusyz2Iw To learn more about the EEW Yarn Counter visit:…
This is not my design but a free download from Freewing RC Planes. Print Settings Printer Brand: Up Printer: Up Plus Rafts: Yes Supports: Yes Resolution: .15 Infill: 5% Filament: Fillies ABS White Category: Models
Double gear grinder with top cover and pushing tool. To build it you dont need any screew, just use some small stick to lock the gears. The biggest file include a 30mm bridge so I made small supports in the model for better print, so…
The flywheel now has a thin ring holding it while it prints, which should break free easily. And I didn't have magnets for the bit so I made the fit tighter so friction can do it's thing.
Fits the full DJI original camera and the O3 camera. May fit other cameras too. This was designed for the T1 but it fits the T2 perfectly too. Just a simple design for a front vent cover pan servo mount. The pan servo screws into the…
Slight tweak to the great work by aviphysics. After my first rough landing with the original, I wanted retaining screws for the rear hatch. Just sink some nylon standoff into the foam with hot glue and you have a very sturdy,…
Light Modifier - Fits the Neewer RGB61 RGB Video Light. PRINT INSTRUCTIONS: Print with supports for the bottom
This plate mounts to the wood rails in the plane with slots for velcro straps. Dead simple, just print. Fits on any bed, needs no supports, etc.
Ratsche Freilauf Freewheel for Filament Spool Winder
These parts are designed for the FreeWing Fa-18C 90mm EDF. These are scale parts to replicate the forward fuselage vents, louvered vents and antennae. You MUST preform ‘foam surgery’ for many of these parts which will violate MotionRC and…
This case is to help enable slow shutter speed pictures, especially in conjunction with the built in Expert RAW mode. It can also help with more cinematic blur in videos, the same as it does for the drone shots. Keep in mind that due to…
These are only the bobbin ends. You need to print 1x eew_mini2_bobbin_tube from https://www.thingiverse.com/thing:3262290 and either 2x of the "gf" (requires glue) or "pf" press fit disks per bobbin. NOTE: The "flat" end is an…
Adding these skis let you do takeoff and landings in the T1 on snow. Use the large skis for loose snow, and the standard skis for harder, packed snow. The tail ski is optional but will help raise the tail on landing so the horizontal stab…
Use the original discs and plugs from Maurice's sectional bobbins . You need: Two tubes Four discs Three plugs I recommend using an inner brim of 5mm to help with adhesion. It peels right off fairly easily, then you can clean up any…
I printed mine with it standing on end as you can see in the pics. It printed good for me in this orientation and looks clean. The template is so you can mark and punch holes in the bottom of the fuselage so you can take the VTX in and…
Vereinfachter Spreewald Kahn für als Deko für ein Geschenk Category: Vehicles
a yarn butler for cones wound on the Electric Eel Wheel Cone Winder. takes the same bearing as the EEW 6.0 bobbin and will fit on the EEW Lazy Kate base to easily knit from. to use less filament i added modifiers to create honeycomb…
I was trying to remove a Kangyue freewheel, and my Park Tool FR-1.3 didn't fit (just barely). So this one has slightly deeper spline cut outs and a tighter overall fit to minimize rounding over the printed tool when used with a 1" /…
Neewer Microphone Wire Cable Clip. Hey!!! This is a Neewer Microphone Wire Cable Clip. that I designed to hold the cable along the mic stand frame. Happy printing. Estikuma If you are feeling generous, please consider buying me a…
Light stand power supply mount for the Neewer 660 video light and similar power supplies. Requires a 3/4" Velcro "One Wrap" tie to mount. More info: https://www.partsnotincluded.com/3d-printed-light-stand-psu-mount/ Category: Camera
This fills in the hole on an EEW Nano 1.x when applying the EEW Nano 2 upgrade kit. This kit is part is part of the EEW Nano 2 Kickstarter. https://www.kickstarter.com/projects/dreamingrobots/eew-nano-2 Here is a video showing how it's…
