Counting matching models…
This is a remix for the excellent remix ( Thingiverse - Digital Designs for Physical Objects - Thingiverse ) of Elescar featuring the same thread and bowden collet insert dimensions - just with 3 arms instead of 2. 2 arms caused some…
The cage for the hot end for the effector by @RyanMaverick_259405 is about 3mm too short for me. This leaves a gap between cage and the effector plate as well as the duct fan and the effector plate. The gap between the effector plate and…
Attachment for microswitch probe to Kossel adaptation of Universal Effector System: https://www.thingiverse.com/thing:6831701 . Parts required: 2x20mm nail to act as probe pin (grind/round the tip before use and sand any rough parts to…
Here is a fully tested and approved effector for Anycubic Kossel Linear Plus making it comaptible with E3d Titan Aero! I've printed it out of PETG and so far so good, no ugly artefacts while printing even at reasonable speeds, the direct…
A part cooling fan mount and nozzle for the 713Maker ball cup effector plate using a 3010 blower. I am rebuilding my old MakerLibre 1515 Mini Kossel and upgrading it along the way. I decided to go with the SeeMeCNC ball-joint effector…
Direct drive for FLSUN SR with the removable Bambu A1 hotend and LGX lite or HGX V2 extruder. Subject to changes! Original 4010 fans can be used Adapters for two 5015 fans Updated adapter for CPAP 3010 Fan for hotend heatsink Insert the…
this model allows the complete modification of the effector of the printer in this way it is possible to mount in a single piece the two fans to increase the amount of air that reaches the piece in this way Not only is it possible to…
NSK UltraLight Effector for Rapido UHF and 5015 Fans (BOWDEN)
"KISS" housing/holder for E3D V6 (normal) and Volcano. The design is based on the stock housing, still making use of the stock mount metal piece. It can be printed without supports - bottom side up. The construction is light to keep the…
Fan duct for the longer V6 Volcano Hotend that fits on the stock effector of the Anycubic Kossel Plus. Very simple design with minimal airflow restriction. I am using it with a clone hotend, so tolerances might vary a bit, also depending…
A very specific title for a very specific part. Technically this is not the entire end effector, just the groovemount portion, so it's compatible with any basic end effector that supports groovememounting (mine is aluminum). Designed to…
An effector housing I designed more than a year ago. Printed with simple PETG it shows no signs of deterioration. Goal was to achieve a light and compact effector for quality printing (reduce ringing for 150mm/s print speed) housing…
better air ducts. Support included. Print in ABS or annealed PLA
Remix of 2 parts in the https://www.thingiverse.com/thing:4329200 to allow it to mount a Bondtech LGX lite extruder. Need to change the lower M3 screw of the Bondtech LGX lite with a longer 30mm one. Also uses a M3 screw instead of a M2…
Remix of treyd's Rigid Carriages for Rostock Max V2
****These models have not been printed or tested yet, I have not had the time to install and test them**** You will need a dremel to enlarge the hole where the original hotend went, to make room for the new one. The purpose of this design…
Remixed from this G2S Universal Effector System: https://www.thingiverse.com/thing:1356159 . Delta arm mounts adjusted to fit kossel. 2026-01-09: added V2 version - an attempt to make it stiffer
This plate lets you mount a Bondtech LGX Lite extruder to a Duet3d Smart Effector as a direct drive. I used 20mm brass standoffs to allow the plate to clear the heatsink. This likely needs an adapter plate to spread out the effector arms.…
This adapter allows for use of a remote fan to cool your V6 heatsink mounted on a Smart Effector. These two parts allow you to plug in the CPAP hose and direct the air towards the heatsink. The additional mounting points are for Berd Air…
This is a simple mount for a 3mm Berd Air pipe, for part cooling. I had to make it because the existing designs wouldn't fit around the wider 80mm effector mount I'm using (Asyborgs 80mm mount). I printed this using TPU, and it does a…
My Take on a clamp for the E3D V6 hotend on a standard He3D K200/K280 effector plate. This is designed for a 1/8" thread Bowden coupler (Like this: https://e3d-online.com/threaded-bowden-coupling ) mounted in the upper part. You could…
All-in-one House/effectors for the FLSUN Superracer with HGX Lite V2 Extruder and X1C Bambu Hotend and TZ V6 Hotend Update: Added Effector/house LGXLite/HGX Lite Combo with X1C Bambu Hotend Also Houses for original effector. Need Effector…
Remixed to work with the MircoSwiss hotend
This is a mod for the FLSUN V400 effector to accept a dragon hotend, a customized WWBMG extruder, and a remote-actuated filament cutter. Sources: https://www.printables.com/model/580837-effector-plate-flsun-v400…
Raisedeffector5 is 2 mm walls, andraisedeffector6 is 4 mm walls
This is still an ongoing development. In short summary, this my take on a heated chamber super racer effector. I envisioned this to be made out of Ti grade 5, ranging from the plate-couplings-screws-hotend frame. Hardware is just a bunch…
This mount is for a V6 Hot End Kit 1.75 / 0.4mm Nozzle for E3D Plate diameter: 36mm E3D diameter: 12mm 3mm diameter holes: 25mm Plates thick: 6mm Category: 3D Printer Parts
A set of protein domains reading able to read DNA and interact with a specific nucleotide sequence. The set is great for explaining the role of the major groove in making the sequence information available from a double-strand DNA…
he hecho una version para imanes de 12 y 13 mm enjoy Category: 3D Printer Parts
Use this model to build from if you want to design your own toolhead for the FLSun T1 Pro. The model is offered in STEP, STL and Fusion360 formats.
I got a clog and didn't want to deal with all the disassembly to get to it anymore so I modeled these parts so I could just leave the cover off. They're not pretty but don't seem to cause any problems. The holes in the extruder fan mount…
Hi! I ordered the amazing Revo micro and wanted to build it into my delta 3D printer. I designed a delta effector which has all of the features would want / loved from other designers. You can download it as well and I hope you have an…
As I have 4x Q5 printers, I have found when I need to work on the effector, separating the cage, plate and hotend can be time consuming. I opened the STEP file in FreeCAD, removed the original wiring hole and added a new larger hole at…
Kossel Mini Revo Micro Mount Effector with Part Cooling and BL Touch Hardware Required 1x Revo Micro (designed for 129.3 spec) 1x 5010 Fan with shroud like this - https://www.amazon.co.uk/dp/B07L2WTH7H (NOT an affiliate link) 1x BL Touch…
MIN Revo Micro effector with mounting cutouts and wire channels for WS2812 LED sequins. LED boards should be a tight press fit. UPDATE: I have added a second version that redirects the hotend wires out the back of the effector for a…
This is a remix of "E3D v6 Effector for Micromake Delta Kossel v2 (with 5015 fan)" by Algenist ( https://www.thingiverse.com/thing:3706236 ). I’d mark this as a remix, but Thingiverse is falling apart and that feature isn’t working for…
My Sunon 5015 V1 were too shaky on the slim fan mounts from cylon25 and they started shaking a lot and the MagLev bearings started to make nasty noises because of the vibrations. So I designed these more beefy mounts from the ground op.…
I wanted more light on my Delta Flyer, so I added a single Neopixel to the effector with a simple printed mount that uses the two holes intended for an accelerometer. I used this LED from AliExpress I use a tiny bit of double sided foam…
An effector and fan shroud mount for the E3D Hemera for delta printers. This direct drive effector works quite well with well designed delta printers like the Ultibots D300VS or the various SeeMeCNC printers that use the SeeMeCNC machined…
This is an effector for 50mm arm spread deltas that will carry a 30mm fan and an E3D V6 hotend. Use a material besides basic PLA. The higher temps it can take, the better.
This is the final iteration of my previous model here: https://www.thingiverse.com/thing:3706236 You will need 3mm m3 heat inserts along with the m3 bolts and nuts.
I'm working on a mount for a new hotend for my V400, and needed a model of the end effector plate. No one seemed to have one available to download, so I made this. It's based on a picture and some measurements with calipers, so I can't…
A fan duct to connect 21mm ID CPAP hose to Universal Spider effector system
Just a remix for my needs, with some changes in design. Original by tondenbraber https://www.thingiverse.com/tondenbraber , who did an awesome job already with the EffectorMinator 1.5. I don't have magballs so i needed to adapt the design…
Just a hollow end effector for the Fairino FR10 Cobot, can be edited and filled in with your electronics. For working version of your own end effector, you may need to and holes for the power and stuff for end effector. I used it only as…
When I found out about Trick Laser's nifty ball-cup Kossel arms with plastic barbells to guarantee arm spacing and reduce joint lash (see http://www.tricklaser.com/ ), I was immediately intrigued, but I needed an effector to use them with…
This is an redesign based on the Circular fan duct by Rod Smith ( https://www.thingiverse.com/thing:2808152 ). This particular fan duct is designed for the E3D Volcano hot-end on the Delta Smart Effector Revision 2. Revision 2 had…
Update 5/2/2019: The Delta Smart Effector has a new revision 2.0 which has moved some of the connectors at the bottom of the effector. This design WILL NOT FIT. Working on a revised model and will release it as soon as available. I love…
Using carbon fibre rod arms means that no printable volume is lost and the head can still reach the extremities of the build plate. With the orignal fisher acylic arms, a bit is lost unfortunately. Added a one piece bottom plate and…
Here is a fully tested and approved effector for Anycubic Kossel Linear Plus making it comaptible with E3d Titan Aero! I've printed it out of PETG and so far so good, no ugly artefacts while printing even at reasonable speeds, the direct…
V1: I printed the parts with PCCF but ABS should be fine. My print settings (feel free to use your own!): 3 walls, 35% infill, no supports Air Funnel First print the file "airfunnel_vx.stl", place the M2 heat insert and use the holes left…
This is a mount for the ADXL 343 (for Klipper fully compatible to ADXL345) accelerometer from Adafruit. It is designed with clearence for a M12 half-nut in mind which is default for E3D and TriangleLab, Mellow etc. M12 heatsinks and also…
I have removed the logos from this design. Bumped the fans out by 1mm so I could fit a 5mm hole for screws without cutting through another hole. Added support for a bambulab p1s hotends as that is what I own. The optional probe mount from…
A remote cooling effector for the delta flyer legacy using a 12033 blower and NF Crazy Volcano hotend
This is a ball-cup arm upgrade set for the Ultibots D300VS, for use with Trick Laser/SeeMeCNC fixed-width barbells and Trick Laser Ball-Cup Arms, as well as the stock Ultibots micro extruder. It should be possible to use this set with…
An end effector for a delta kossel with a cutout for a M12 Nut.
Smaller effector plate for the Dreammaker OverLord Pro & non pro. Centers the nozzle and should get a print diameter of 180 ~190 mm on the OL Pro. It uses the stock 60mm rod spacing on the sides so you don't need to replace the OEM…
Kossel effector(hole distance 30mm) Print Settings Printer: DIY mini Kossel Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.25 Infill: 20% Category: 3D Printer Parts
This fan shroud is for object cooling. Category: 3D Printer Parts
This is a remix of the magnetic effector with the hotend zProbe. I modified it to use micro limit switch. Need to print the hotend mount form https://www.thingiverse.com/thing:1259061 . Category: 3D Printer Parts
This kossel effector is a remix with diamond hot end. It is a 40mm version cooler shield. You need a very powerful 40mm cooling fan. This effector is still work in progress and not test yet. Add v2 for 50mm cooling fan, and increase Z…
I modified the effector from Kossel source file. The filament feeding hole is enlarged to fit the tube holder. Category: 3D Printer Parts
****************** *** ITALIANO *** ****************** Ho scelto la Super Racer per la sua struttura e per le sue potenzialità nello stampare filamenti semplici a grande velocità, come PLA e PET-G. Appurato che l'Hotend di fabbrica non è…
***************** *** ITALIANO *** ***************** Non è più un problema stampare il TPU con la Super Racer! Ho progettato un nuovo case per trasformare l'Effector da Bowden a DirectDrive e, per l'occasione, ho pensato di installare uno…
CAD file of the FLSUN SR effector plate. May not resemble the real part a 100% but comes pretty close, if you want to design accessories. I'm not completely sure about the depth and the diameter of the holes for the ball joints, as I…
* EDIT 5/4/22: Added the 'brba' Fan Duct + 4020 Topside Adapter as this performs 300% better with the original Mosquito than the Fan_Duct_Original_V1.stl. * EDIT: added a Cable_Guide_Extender for those who hate the cable tree dangling to…
Disclaimer: No animals were harmed or injured during testing and assembly For Anycubic D 'Predator' Delta printer only. Designed for use with: MagBall arms (Haydn Huntley) Orbiter Extruder 1.5 (for 1.75mm filament) 2 x 4020 part cooling…
This has a 60mm spacing for the rods, and uses the rod ends with the swivels to attach. Also has the mount for a BLTouch, but you could probably make a mount for any of the other probes out there. Uses a Ender 3 style 40mm part cooling…
These are a bracket and a fan duct to attach a 40mm x 10mm print cooling fan to the Duet3D PCB dela effector described at https://duet3d.com/wiki/Smart_effector_and_carriage_adapters_for_delta_printer . Category: 3D Printer Parts
Remixed for an ANET A4 that has 25mm effector offset (but 50mm between diagonal rods) and with BLTouch v3 support from kirill91's great design (which was 40mm between the rods). This allows the stock carriage slides to be used. You don't…
When building the Monster Kossel, I got Igus rod ends instead of the Traxxas variation. I couldn't re-use my Mini Kossel's effector, but I really liked the way the clamp worked to keep it all in place. Cue this effector. Spacing is…
Here's a E3D Titan aqua mount for 713maker effector plate I designed. This model can only be pulled off if your printer is particularly dimensionally accurate and is capable of bridging a circular gap. It's used on my ultibots D300VS+ but…
This is a model to mount a Bondtech BMG X2 and E3D Cyclops+Aqua directly to a 713maker effector plate. This is one of the few dual direct extrusion methods available. Category: 3D Printer Accessories
I really liked the design of the Kossel carriage bei 3DPB. But it seems he lost his "source files". So I re-created the desing for my Kossel built using the Duet Smart effector and Haydn Huntleys Magnetic Rod-Ends (or at least the "balls"…
surface printed without supports preferable petg layer height 0.2
printed with the part of the 2 holes on the printing plate without supports layer 0.20 recommended material petg
The effector plate for a Flsun Q5 is quite large and heavy, so I came up with these designs. The effector uses a 5015 radial blower fan as part cooling fan. 2 effector plate designs ( I prefer and use the V2 ) Multiple fan duct sizes…
This effector is designed for use with the E3D V6 heatsink & SliceEngineering Copperhead Hot Block. You need brass nut.
I used to have this cooling duct on my i3 which inspired me to design my own magnetic delta effector with a built in print cooling fan. I also wanted to put a capacitive probe on it, which it ended up in a pretty awkward position right in…
This is a solution to mount the SmartEffector's mounting plate to the QQ-S' sliders, and yes, by printing your own sliders. Word of Caution : You might want to get another batch of bearings/bushings as the original ones can be hard to…
Effector mount that allows you to run any Rostock Max V2/V3 hotend and corresponding mounting solution including the E3D V6 and clones, or the HE280. I measured the mounting holes in the stock effector on the Kossel Clear magball effector…
Designed this to replace a string hanging from the top of my delta printer holding the end effector cables up as the electronics are installed under the print bed. Just print and install to the bottom vertical profile and push the cable…
This is my view on a delta end effector and matching carriages. I use them on a Kossel XL with 245mm diameter build area. They are designed to be used with Haydn's Carbon Fiber Arms and E3D v6. Arm spacing is 60mm to improve stability.…
You may need to trim after printing Category: 3D Printer Accessories
This is a adapter to mount a solder paste needle (or similar) to your smartEffektor. The mounting thread is M12x1.5 The nut has +0.5mm Tolerance for 3D printing. The "Push in Connector" has an M5 thread but can be drilled out I'd say.…
This is a end effector for Kossel-Mini style printers using the new E3D mounting standard. Print it from a high temperature plastic and make sure the heater block is well centered otherwise the end effector will soften and deform. Print…
Remixed this from the original source, only changes made are adding bevels and extra space on the rod-arm mounts to be compatible with normal Traxxas joints and a sacrificial bridging layer in the centre to eliminate support material. As…
Adapter to mount an orbiter 2.0 extruder to a smart effector board. Its probably easiest to print with the orbiter side rotated towards the build plate and with supports for the smart effector mount holes. It's designed to fit my kossel…
This is an effector that has the mount for the hotend raised so that you can get that extra 5 cm of build height. My sintron kossel mini has some Chinese e3d clone, so I measured it and arbitrarily picked a height for the design, but it's…
Hardware required includes: x1 “Regular Size” Fine-Point Sharpie (Any color works) x1 Compression Spring x4 Socket Head Cap Screws
This is the effector I've been using on my Kossel. It has the heatsink mounted above the arm joints, and space for either a Volcano or regular V6 heaterblock, with an adjustable mount for an IR sensor. There's space for the 30mm fan, and…
Hi, I've been using user swedishvaperuk's e3d v6 effector ( https://www.thingiverse.com/thing:2767236 ) on my Anycubic Kossel linear plus for the past year and absolutely love it! However, I wanted to re-vist the part cooling situation…
Flsun SR dragon hotend mount (current version v1.2) Effector plate modification required !!! (expand hotend center hole to HS size, min. r11.2) Designed for M3 5.6mm brass insets For hotend holder use 4x M3 16mm screws Two resized…
UPDATE 2: Increased the size of the counter screw hole and around the hotend mounting groove to fit M3 insets. Old files for self-cutting screws still online. These may need some re-tightening every couple dozen hours of printing. UPDATE:…
There's a newer, MUCH better version available, based on my v2 SR mount . FLSUN QQS-Pro Sherpa/Orbiter Housing I had trouble leveling the bed after adding a Volcano hot end to my Flsun QQ-S Pro with Foxies firmware with the head stopping…
For printing with fairly high temperatures, I needed more airflow. This is an effector using only 40mm fans. Youll need brass inserts, i used 4,5mm od M3 inserts and 3mm od M2 inserts. Might need a bit work with a multitool for a good fit…
This is version for smart effector and 40x40x10 fan. Needs 4 M2.5x20 screws. I've used brass tubes with 4mm OD from eBay and used drilling jig from https://www.thingiverse.com/thing:2445660 to drill holes. Print Settings Printer: Kossel…
v1.3 Upgrade - I did 3 times thicker, to be stronger, totally fail. I need to change my mind. v1.2 Upgrade: - I started design again so object is solid (easier to modify) v1.1 Upgrade: -Boundaries are rounded with 0.4R -Rotated 90º so it…
