Counting matching models…
Modeled in Fusion 36O with dimensions: - width: 34 mm - height: 47 mm - thickness: 0.3 mm The key is to find a setting where the flights will print on one perimeter. The arachne generator helped a lot. Use support material or the flights…
I redesigned the flights to print as easily as possible on a standard 0.4 mm nozzle. You can also use the organic supports in the new PrusaSlicer 2.6.0. However, this model is very specific, so I created my own supports to save some…
Design highlights Uses minimal filament to print Prints fast (about 2 hours) Defaults to the optimal 12° Angle is fully adjustable with the feet Built-in bubble level Attached to the stand using the front tripod mount and the rear "thread…
This page contains the instructions and files for printing and assembly of the throttle quadrant module. (electronics and other details for the whole unit on main page “ OpenFlightSimConsole base ”) Fusion 360 model is provided for anyone…
Darts Holders Simple 3 darts holder Last Resort Flights - they are'nt perfect but if you have nothing else :P Real Darts flights here https://www.prusaprinters.org/prints/127821-real-darts-flights-glue-needed This is a remix: The base of…
Summary Stopper for office chair for simracing and flightsimulators. Due to the round design, there is no need to adjust the wheels orientation. The model is fully parametric. A list of all variables and their default values: d_wheel =…
CHECK THE NEW ONE ON MY PROFILE https://www.printables.com/model/1134797-v20-dart-hub-stand-display-holder A simple to print solid darts stand holder /display. With space to hold your favourite stems and flights for that set. The top part…
Since I liked the original model but I did not like the idea of printing it vertically, I've decided to split it into two parts which intersect down the middle. Now it prints flat on the bed quickly and easily, with no supports. I…
This page contains the instructions and files for printing and assembly of the flaps lever module. (electronics and other details for the whole unit on main page “ OpenFlightSimConsole base ”) Fusion 360 model is provided for anyone to…
Navrhl jsem tenhle jednoduchý a pevný držák na Joystick s kovovým šroubem. Šroub a matice pro dotažení ke stolu jsou M12X50. Inbus Šrouby pro uchycení joysticku jsou M5X20. Inbus Díl matice nalisovat na šroub M12. Tiskne se to snadno bez…
Here’s a simple leveling stand for a MEVO Gen2 golf launch monitor. There is a slight amount of X-Y wiggle room in the tray area so it’s easy to make very fine left-right adjustments without having to re-level the unit. I didn’t add a…
Needed 3 linear ball bearings 8mm rods 12,5 cm long 3 linear potentiometers Arduino pro-micro / leonardo 04-10-2021: Added an updated version. You can now pick from 2 case options. One for panel mounting and one for mounting with screws…
UPDATE 02/04/25: Added Ultimarc & M10x30 Hex nut compatible raptor bodies (Many thanks to user francislej ) UPDATE 31/05/24: Fixed errors in Raptor MAIN body STL, now V45. Print upright on bed. UPDATE 29/05/24: This has been exclusive to…
This pedestal was designed to closely resemble the A320 cockpit, but some compromises had to be made so it is not entirely accurate. This is a work in progress and a lot of documentation is still missing/unorganized, please use the…
This is a great flying, Frisbee-style disc made using an upcycled NEW Prusament spool component. Design goals included: Strong flight performance Comfortable handling — no sharp edges, burrs, or protrusions Clean, appealing appearance…
VTOL VR JOYSTICK A desk mounted VR controller dock/joystick for VTOL VR. The design allows the physical joystick to be in the same location as the stick in the game and to not interfere with using the MFD’s and control panels. Rubber…
I remixed this brilliant design and the technical implemenation under following preconditions: - Simplification - Print more and buy less - all my modules for my Flight Simulator Homecockpit should be totally self-sufficient and stable,…
A jig for engraving Dart Flights. Made for KFlex Flights. Can be adjusted for other sizes
made a set of my own darts. Had to design some flights. Drawn from original Jarts. Wings are a little thicker than the original by .020" for strength. Inner diameter is .300" outer diameter is .500" wings are .060" thick
UPDATE 02/04/25: Added Ultimarc & M10x30 Hex nut compatible Tron sticks (Many thanks to user francislej) UPDATE 01/10/24 : V1.1 now has the ability to have the wiring pass through the joystick stem. 13/06/24 : After spending two years on…
I ordered a broken VelocityOne for 20bucks from the UK, my reason being to find out whats wrong with it and repair it. Turns out its totally working. But it came without any hats or throttlegrips. So i designed a range of them and decided…
FreeCAD model is provided for anyone to customize or remix the design. This model is still in develoment. The current version could be improved to be more sturdy, which I might do later. Materials: -10k potentiometer with 6mm dia shaft…
I am selling a file of my dart flights. They are great for Amateurs and perfect for 3D printing. They have a total length of 73mm and fit perfectly on conventional barrels. The file is in STL format. and stp. have.
I remixed this brilliant design and the technical implemenation under following preconditions: - Simplification - Print more and buy less - all my modules for my Flight Simulator Homecockpit should be totally self-sufficient and stable,…
This cradle and tumbler was created so that I could code the function buttons on my velocity one controller for my XBox system with multiple button press capability to achieve 5 layers of function button options. The cradle sits next to…
Real 3d printed Darts Flights - glue needed assembly in the comments :) You need 4 for every flight Have fun Its still a emergency replacement ! Print 0,1 layers (ironing recomended)
PMDG B737 Trim Wheel for Flightsimulator. This trim wheel can be combined with the Logitech/Saitek Throttle Quadrant possibly supplemented with Speed Brake Unit. The communication with FSX / MSFS is done by FSUIPC and a LUA program to the…
Flanker style stick for diy hotas. Files for both a left and right handed version are provided. Three out of five multi switch guards can be changed to allow for switching between movement restrictions without reprinting the grip. Test…
Different knobs for flightsim. Created in the past year. See my other designs.
To enhance the flying experience, I designed two new anatomical knobs for the Turtle Beach Velocityone Flightstick . Knob 3 has a longer shaft and makes throttle operation much easier. Comments and suggestions are welcome.
Allows the stand to be printed on a smaller bed.
If youre missing a handrest for the Turtlebeach in either Left or Right, here is one that you can print without supports. You just need 2 M3 Screws of some sort, ideal would be M3x8, M3x10 or M3x12 (as all fit, and the thread is long…
As a new FlightScope MEVO Gen2 owner I wanted to speed up my setup. This is a clip-on bubble level that will quickly get you very close to the recommended 12* tilt and 0* roll. Use is simple. Just drop it on top of the MEVO Gen2 and level…
Made a remix of 2 different stream deck holders for the Honeycomb Bravo flight sim, noticed that there wasn't any mounts for the stream deck plus so had to mix and match some. https://www.thingiverse.com/thing:4730037 +…
Inspired by multiple makers on this site! Pleomin Lucas S_G I wanted to design a case with a slightly stronger hinge and is more specific for my use case (no pun intended) and multiple requests to upload it here on the site! There are two…
My brother wanted a powered mover for his Mevo+ golf simulator sensor so it can quickly switch back and forth from positions for a Lefty to a Rightly in his simulator room. So I made this up. I used it as an excuse to practice my…
1/10 scale RC car Roof hood went
I'ts easy to print joystick. You can useit for flight simulators. 0.16 20% No support need
I bought a few Turtlebeach Flightsticks broken for quite cheap, because i think they look nice, dont have an app you need to install on windows (but you can use an android/iphone app to change deadzones, orientation, stick response and…
As a new FlightScope MEVO Gen2 owner I wanted to speed up my setup. This is a simple reel to store an 8’ long nylon cord used to quickly measure the exact required 8’ distance from the MEVO Gen2 to the tee. I keep a couple of tees with…
I am preparing for my microlight pilot's license on the Ikarus C42B, and the throttle is a lever located between the legs (and the steering control is between the two seats). When you have a few years of FlightSim experience with…
UPDATE: Please find the rest of the project files here: https://www.thingiverse.com/thing:5330660 The wait is over! Digital Flightstick Part 2 (The FlightStickening!) is here and ready for you to force your 3D printers to print.…
UPDATE: Please find the rest of the project files here: https://www.thingiverse.com/thing:5264016 Here is my first successful attempt at a 1-piece, 3-firebutton, digital flightstick. The three momentary push buttons fit snugly in their…
Usually the Honeycomb Bravo quadrant is placed to the right of the yoke. This model let's you mount the FlightSimBuilder GNS530/GNS430 at an angle to properly see the screen. I included 2 models for you to choose. The difference is how…
Der originale Detend des Moza MTP ist aus meiner Sicht für einen Airbus-Schubhebel nicht geeignet. Der von mir entworfene Detend hat alle für einen Airbus notwendigen Rastungen: Rev Full, Rev Idle, Idle, Climb, Flex, TOGA. Druck: PLA, 3…
Case for K-flex flights, or flights with stems, just add hairtie or rubber band.
See image for slicer settings and material. Parts required for mounting onto T-Slot Aluminum Extrusion… M5 x 10mm Hex Countersunk Screws: https://www.amazon.com/iexcell-Thread-Socket-Screws-Finish/dp/B0D77PPKNX/?th=1 T-Nut:…
I have an Ikea desk whose thickness is about 20mm. This model holds the FlightSimBuilder GNS530 at an angle facing you (if you use it to your left) while attaching it to the desk so you can press the buttons without the GNS530 pulling…
Just a simple clip to keep a set of dart flights together. It utilizes a small nipple to keep things tight. See my other models (including other dart accessories models) at https://www.printables.com/@MichaelBuchDesigns Cheers!
The Golden Claw! A mythical arcade flightstick that has absolutely nothing to do with a certain beloved Elder Scrolls game that Bethesda keeps re-releasing (and to be honest, I keep buying). It was just an opportunity for me to sneak in a…
Quick Release https://www.aliexpress.us/item/3256806823650864.html GX12-4L https://www.aliexpress.us/item/3256802442302567.html Bolts/nuts to suit your rig plus M3 6mm round head for the connector plates Epoxy glue It's been a while since…
it is a conversion that goes on the thumbsticks so that you can use an xbox controller with a drone simulator
Mounting plate to work with the Thrustmaster TCA Airbus Desk Mount
This is a spacer block to suit a standard 18mm desktop there is also a Knob to take a stand 12mm Hex bolt for the Držák Turtle Beach VelocityOne FLIGHTSTICK The 3MF has a couple of modifiers to print 100% infill where the bol conacts the…
This is a basic button box designed by me for use in flightsim. It features two dual rotary encoders, which can be found here: https://www.thingiverse.com/thing:4373531. The project is currently not finished, however there is progress on…
Stratoflights Halterung für Experimente. Halterung an den Holzstab stecken.
The original pinholder has a tendency to break with age. A simple fix for an expensive piece of gear.
Edit_1: Part is now symetrical and it should be able to get assembled in a Rectangular Form Print Ongoing Edit_2: Added holes for K-Flex and Slider for Flights. Edit_3: Hole size adjustments Minimalist modular dart holder designed for…
the pogo connections ended up digging into the contacts over time. i made this plate to make it thinner and thinner till i get a solid connection again.
I didn't have any ribbed rubber on hand, but TPU was still loaded in my printer. So I designed a simple TPU pad to glue into the clamp's recess. It prevents the desk from getting damaged and greatly improves stability! Material: eSUN…
made a set of my own darts. Had to design some flights. Drawn from original Jarts. Wings are a little thicker than the original by .020" for strength. Inner diameter is .300" outer diameter is .500" wings are .060" thick
Case for K-flex flights, or flights with stems, just add hairtie or rubber band.
Stratoflights Halterung für Experimente. Halterung an den Holzstab stecken.
The original pinholder has a tendency to break with age. A simple fix for an expensive piece of gear.
This is a great flying, Frisbee-style disc made using an upcycled NEW Prusament spool component. Design goals included: Strong flight performance Comfortable handling — no sharp edges, burrs, or protrusions Clean, appealing appearance…
This is a great flying, Frisbee-style disc made using an upcycled NEW Prusament spool component. Design goals included: Strong flight performance Comfortable handling — no sharp edges, burrs, or protrusions Clean, appealing appearance…
It has two usecases. It is mainly for those who want to use the left Meta Quest 3 Touch controller as a VR motion compensation reference tracker for simracing or flightsim rigs (See OpenVR Motion Compensator by dschadu)… or if you just…
