256 models
Bracket for Govee Neon LED Strip Light. I've had great results printing without any brims with PLA on Smooth Steel Sheet PEI. Screw hole is small enough that it didn't need any supports.
Print approx. €0.25–€0.30 excl. taxPreliminary estimate for one variant
Made at the request of a Printables community member, these mounts are a traditional mounting bracket with dual offset screw points. These mounts are best used with typical flat bottom soffits. If you have angled soffits or rafter tails,…
Print approx. €0.12–€0.15 excl. taxPreliminary estimate for one variant
Like this mount? Check out our brackets too! https://www.printables.com/model/1083606-govee-compatible-bracket-for-permanent-outdoor-lig Brackets to mount the power brick and switch brick for Govee Outdoor Pro lights. Suggest printing…
Print approx. €5.69–€6.95 excl. taxPreliminary estimate for PETGSource material: PET
Die beiden Govee Clips brauchte ich für ein bestimmtes Wandmuster. Dabei habe ich den Doppelten Clip für enge 180° Kurven benutzt, da 2 Clips ohne eine Verbindung nicht gehalten haben. Ich gebe euch aber noch die Rohdatei dazu, dass Ihr…
Print approx. €0.57–€0.69 excl. taxPreliminary estimate for one variant
Instead of having the T2 camera sit on top of the TV this stand helps to position the camera in a good position in front
Print approx. €2.91–€3.56 excl. taxPreliminary estimate for one variant
Did you install the Govee Permanent Outdoor lights only to discover that you're being blinded through your window? Well, here's the fix for that. This model can completely black out individual lights, or work as a diffuser. It all depends…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for PETGSource material: PET
This holder is designed to securely hold the remote for your Govee LED light strip. My model was H619C and had a pill shaped remote. This is the remote most of their strips use nowadays, but you may want to check before printing this as…
Print approx. €0.98–€1.20 excl. taxPreliminary estimate for PETGSource material: PET
Compatible with this Govee thermometer or any other device that fits in the basket hole:66x21.5mm
Print approx. €1.69–€2.07 excl. taxPreliminary estimate for one variant
Needs 2x countersunk Screw for Rigmount is designed for M8 2x M6x30 socket head screw & 2x M6 nut for mounting the light. the design allows for about 30degree of tilt in each direction
Print approx. €0.81–€0.99 excl. taxPreliminary estimate for one variant
My friend enjoys using his humidifier, but due to its placement, he needs the mist to be directed at a different angle than what the included parts allow. This replacement mist nozzle is designed to push the mist output slightly further…
Print approx. €1.17–€1.43 excl. taxPreliminary estimate for PETGSource material: PET
Print Settings (Should be in 3mf project file): Material: PETG - PLA will stress fracture over time and PETG hinges more nicely Layer Ht: 0.3 mm Perimeters: 3 Top Solid Layers: 6 - Helps with waviness from the default 4, purely aesthetic…
Print approx. €4.34–€5.31 excl. taxPreliminary estimate for PETGSource material: PET
Parametric Bracket for attaching Govee Neon LED to all kinds of exposed frames. I've used it on my Jysk TRAPPEDAL bookshelf. I've had great results printing without any brims with PLA on Smooth Steel Sheet PEI. Screw hole is small enough…
Print approx. €0.35–€0.43 excl. taxPreliminary estimate for one variant
This is a holder that is compatible with the Govee Bluetooth Thermometer Hygrometer (H5102). It positions the sensor at an angle, making the screen easier to read. There is an opening on top to access the button that changes the units…
Print approx. €1.01–€1.24 excl. taxPreliminary estimate for one variant
The lights used to come with clips like these, but now only use adhesive strips, which aren't ideal. I like printing them wiht the screw hold facing down and then just using a brim for support. PLA can be a bit brittle, so a little more…
Print approx. €1.70–€2.07 excl. taxPreliminary estimate for one variant
This is a set of parts I made to re-enforce the 3M adhesive used to mount Govee Permanent Outdoor Lights Pro (H706A). Light Mount : A small frame that goes around the outside of a light that can be screwed to the mounting surface to…
Please feel free to support me so I can create and share more. Any amount is much appreciated PayPal me I've seen that a lot of people have issues with the 3M tape on these LEDs. So not wanting to go onto my roof more times than I have to…
This Govee Pro outdoor LED light (HERE) mount is friction fit around the top of the LED but remains loose around the bottom. This allows the mount to be placed over the strand (and not fall off) while attaching outside. The design is…
Picked up a set of the Govee RGBIC permanent outdoor lights but I'm not a big fan of the idea of using the adhesive. Partially because I don't want any residue to clean up in the future should these lights fail or loose their appeal and…
I needed to keep the lights from tangling up in the wind so I put this together as one of my first OnShape parts. Onshape Link
Govee Permanent Outdoor Lights Pro Power Supply Wall Mount
Four 90 degree curves for Govee LED strips Short versions have a 25mm straight part, long versions 50mm. The one that's less narrow has an inner radius of 25mm. Screw holes are optional, I used 3m double-sided tape.
Slight modification to the narrow mount introduced by Gelap with removal of two of the corners so there are only two mounting holes. Added two alternative versions for mounting the junction between light strings. One with just a single…
I guess Govee doesn't want to sell accessories separately, so I've modelled both style of brackets that originally came with the light bar. Mount Govee light bars to clamp style monitor stands. I use the light bars as desk lamps, so the…
This is for those who ordered the Neon Light strips back when they only provided 5 of these clips or someone who wants more. If not, I'm sure someone can give this another purpose! 15% infill 0.20mm
The power supply mount is compatible with the 36V 2A PSU model SOY-3600200US-306 which comes with Govee RGBIC LED Permanent Outdoor Lights models H705A, H705B, and H705C. The controller mount is compatible with the aforementioned models.…
With the Govee permanent outdoor lights to get the best scalloping effect each light needs to be placed the same distance from the house. So, I made this little tool that you can use to place one part against your house and hold the Govee…
I made this spacer tool to help install the excellent snap in Govee light holders from: https://www.printables.com/model/593227-govee-rgbic-led-permanent-outdoor-lighting-mountin This allows me to space them 8cm from the house, which is…
Simple wall-mount brackets for both the power adapter and controller module that come with the Govee Permanent Outdoor Lights kit. Mine are the non-pro model, from pictures it looks to me like the pro model uses the same power brick and…
This is a gable mount for the outdoor govee lights square model Print Settings Printer Brand: Creality Printer: K1 **Rafts:** No Supports: No **Filament:** Creality PLA, PLA+ white Notes: The gaps are a bit tight. I am sure you could…
Simple wall mount for a Govee H5179 sensor. Flat back with screw hole for a fastener or use with a command strip or some double sided tape.
There are two versions of this tool provided: v1 - The tool pictured in the cover photo - This is the tool my brother and I used. It has a label so years from now you or whoever finds it will know what the heck it is. v2 Slim Edition -…
Govee H706A Permanent Outdoor Lights Pro Mount Bracket I’ve designed two versions of this mount: A side-mount version A narrow-edge version requires just 1.5 inches of space. Both versions are designed with #8 self-tapping screws. I…
Recommended Fastener is Number 6 flat head screw https://www.mcmaster.com/catalog/129/3356/98903A206 P1S 0.2mm layer PLA tough Tree Supports
Diffusion panels to surround Cync Hexagon Light Tiles or Govee Glide Light Panels. Print in Vase Mode with a .3 layer height so the deepest part of the angled face touches the back face to prevent warping. You can get the 7 pack of Cync…
This is a bracket to be able to mount a light at the top center of a roof gable. It doesn't matter the pitch of your roof. You need to print 2 of the “gable mount 2” file. Outside of that it is pretty straight forward. I used #8 1/2"…
Govee wire clips Both versions print OK in their modelled positions on my Voron 2.4r2. I used White ASA, 15% infill, for my test prints
This mount gives you a flat surface to mount a Govee light in the top center of a gable roof peak. I designed it to perfectly fit a roof with a pitch around 5.3/12 with the arctan(5.3/12) = 23.83 degrees. It should work fine for roofs…
A basic wall mount for the Govee 6-button remote. I added a model with holes for screws although that seems like overkill. The model printed fine with PLA and no brim or supports if oriented properly. This is my first design, just had a…
Saw a couple really nice designs for the mounting of these lights, but they were too intricate and not conducive to printing 120 of them to install my lights. Made this one to mount the lights at a 45 degree angle and adaptable to either…
This is a govee wall mount. It is used when there isnt a soffet to mount the lights on. it can also be used to mount the light to fences or around handrails or the bottom of decks. There are 4 different sizes 3 inch, 2 inch, 1 inch, and…
Set of two mounts for the Govee permanent Christmas lights Pro pucks. One mount has the added feature of a light shield to block direct view of the light lens from most viewing angles. I printed 15 at a time in a Bambu X1 Carbon, I'm sure…
The Govee gable mount is a must to secure your govee pro lights to the peak of the soffit and keep the light centered for a better more professional look. PETG, ABS, ASA recommended 0.2mm Layer Height 2 Walls 10-15% Infill Supports needed…
Nachdem bei mir die originalen Klebepads der Govee Glide Hexa Panels nach einiger Zeit nachgegeben haben und die Lichter von der Wand gefallen sind, habe ich diese stabile und wiederverwendbare Alternative entworfen. Anstatt der Klebepads…
I do not believe there is a way to get the wires of the lights mounted in a way that will look good that won't eventually sag. The premade track options are expensive and not very flexible. Undersill trim is relatively inexpensive and can…
This tool is for the Govee Permanent Outdoor Lights Pro installation. It is an installation tool for VisualReversal 's (Printables website) friction grip mounting brackets. It mounts them at a Govee-recommended distance of 8 cm or 3-1/4…
Pretty simple print. I printed at 10% infill, .3mm layers with 2 perimeters. It's not a perfect fit, but it holds it great, and it doesn't cover any of the light. Hopefully this doesn't violate any IP rules-- I measured the lightbar and…
Gelap has made a great assortment of mounts for the Govee Permanent Outdoor Lights Pro kit. After installing them, I found a need for a few extra accessories to clean up my install. // UPDATE DEC 2025 Added my 4" x 8" approx. S Curve that…
Wall mounting support for Govee Neon LED Strip Light support Fits for this led strip light: https://eu.govee.com/collections/indoor-strip-lights/products/govee-neon-led-strip-light
Adapter with support base to the Govee or similar shaped Hygrometer and Thermometer. With this hygrometer/thermometer you can monitor the temperature and humidity inside ACE pro remotely via Bluetooth, receive notifications for changes,…
A cover I made to block some of the govee lights installed at a friends house. I'm not 100% sure on the fit, but will update once I hear back. F3D and step files are included as well in case others need them. Made with PETG 0.2mm layers.…
I purchased a 5m strip of LED lights and Govee only included 5 clips. So I replicated it to make a few more. I countersunk the screw hole and made the piece that goes over the LEDs 13mm wide instead of 14mm because of the distance between…
Slides over lights mounted on the soffit with the 3M tape. Secures by covering the wire on both sides
This is a simple design for mounting your Govee H5126 “smart button switch.” So you can keep it in one place and move it when needed. I printed this on a Bambu Labs Carbon X1 printer with AMS. I used white Bambu PLA, Though, with the…
This is a spacer that separates 2 strands of Govee curtain lights. I printed multiple sections of jeepin95's original 4-strand model (transparent PLA), and wanted to join them together. No changes to the original except it's cut in half.
Shoot me a message if you need the *.step file.
This model replicates the clip that comes with the Govee LED outdoor strip. It will likely work with other brands as well. I printed with: 0.2 mm layer height no supports needed if print on the side as shown in the 3mf Probably best to…
Govee RGBIC light mounts
Die ist eine Wand Halterung für Govee Wandleuchte WiFi RGBIC LED Lightbar This is a wall mount for Govee Wall Light WiFi RGBIC LED Lightbar Print Settings Supports: No Resolution: 0.2 Infill: over 15%
Govee Curtain Light Minimalist Brackets These minimalist brackets are designed to be printed in PETG or other strong, UV-resistant material and are modelled for self-tapping 8x1 lath screws. Printing Notes: - If you like clean prints,…
The Govee gable mount is a must to secure your govee pro lights to the peak of the soffit and keep the light centered for a better more professional look. Works with Govee Prism H707A(100ft) & H707B(150ft) & H707C(200ft). Recommend…
Made for Govee permanent outdoor LEDs. Using this the keep the lights aiming perfectly vertically straight when mounting along the sloped are of the roof line.
This is a custom bracket for Govee Permanent Outdoor Lights (non-pro version) for vertical plane (90 deg) installation. I built this bracket specifically to install govee lights on my wooden fence with the lights pointing down. The…
I remixed Kalcemo's Bambu X1C Chamber Hygrometer to hold a Govee Bluetooth Hygrometer Thermometer H5075 I had laying around. It's visible from the P1S camera for when I'm not within bluetooth distance. I printed this at 0.1mm layer height…
Quick little print so you can hang a Govee Thermometer using the Keyhole mount on the back in a polytunne/greenhouse or wherever you need to hang it. It has 4mm hole for string/rope for hanging. This print makes it easy to attach and…
This is a mount for LG OLED TVs (tested on a 55" C4 and a 65" C3) for the Govee DreamView camera. No need to use the adhesive directly on your TV.
For this AMAZON Leds.
Govee Hygrometer (H5075) Magnetic Mount (12x3mm Magnets) For mounting Bluetooth connected Hygrometer in printer, drybox, etc. H5075 keeps history so you can keep track of dry box humidity and temperatures over time. No support Press the…
This mount is designed for seamless installation of the Govee RGBICWW Light Bars using a standard 100×100 VESA pattern. It provides a sturdy and practical solution for integrating light bars with your monitor setup. Key Features: Easy…
I live in an area where eves are not aluminum rather wood beams and stucco. Using the adhesive strips to attach the Govee lights was not an option. This braket secures each light and allowes for you to screw it into the facia exposed wood…
Govee tape fail? Here is a simple bracket to hold the lights up. Low profile as possible to not grab attention, and doesn't go over the lense and take away from lighting effects. .2mm layer hight with a .6mm nozzle no infill Any filament…
Print it standing vertically. supports needed on the plate.
Needed some consistent spacing but also needed the ability to put some lights in locations I didn't have easy ladder access to so adding on some features to help hold the light in place, and attach to a broom handle to reach those spots.…
Govee Permanent Outdoor Lights Pro 2 Mounts If your home is like mine, your soffits require a bridge at specific intervals. This model creates a secure bridge mount with the security benefit of hiding screws behind the cap with a snap…
Mounting bracket (30mm) LED that covers the front face and sides. Useful for matching the color of your house or soffits. Also redundant if the VCB tape fails. The printed part is a snug friction fit so attaching them before screwing them…
Design to put your Govee Immersion Camera on the Top of the LG 65UJ6309 Category: Video Games
A holder for the new remote of the M1 Matter Light strip from Govee. The bracket can be glued or attached with two screws. Eine Halterung für die neue Remote des M1 Matter Light strip von Govee. Die Halterung kann geklebt oder mit zwei…
Although I made a couple of versions with screws I preferred the clean look of VisualReversal's holder https://www.printables.com/model/593227-govee-rgbic-led-permanent-outdoor-lighting-mountin. This has a single, hidden screw So I made a…
This is a wall mount bracket for the Govee H5075 thermometer. It uses two 3M medium command strips to attach to the wall. The strips are hidden behind the thermometer and the bracket has an opening to allow easy for removal of the strips.…
This mount is for the NON-PRO Govee lights. The Govee gable mount is a must to secure your Govee lights to the peak of the soffit and keep the light centered for a better more professional look. Recommend printing in PETG, ASA, or ABS.…
Quick REMIX of jlconlin's Govee LED strip clip. Intended to work with Govee COB LED light strip Pro
Brackets for Govee H706C Permanent Outdoor Lights Pro Remix of https://www.printables.com/@Gelap https://www.printables.com/model/630613-govee-permanent-outdoor-lights-pro-mounting-bracke
I was looking for a lighting solution for above my desk when I saw the Govee RGBIC floor lamp in the corner of my room. I designed a mount complete with cable management. After unscrewing 8 screws connecting the light rod to the base and…
I broke one of the mounting clips during the install and needed something to secure the light with a broken tab the only work for Govee Prism Permanent Outdoor Lights H707A(100ft) & H707B(150ft) & H707C(200ft). Recommend printing with…
Mount your Govee H5075 Digital Hygrometer Thermometer onto the door of your Bambu Lab P1 Series or X1 Series printer to conveniently monitor the enclosure's temperature and humidity.
Quick mount I made for the T3 camera on top of A2 oled. Used double sided tape to back of tv to mount. Keeps it from moving around.
This is a bracket to hold Govee permanent Christmas lights (non-pro). I cut it shorter to use less plastic.
I find it useful to monitor the huminidy and temperature inside the printer chamber - I did not came across anything for Govee Sensor - so there you are - maybe someone will find this useful.
3D-Printed Holder for Govee Outdoor String Lights 2 This custom-designed holder is specifically crafted for Govee Outdoor String Lights 2, providing a stable and practical solution for secure mounting. Engineered for simplicity and…
I designed this for my Govee LED Light Strips, so I can easily cast the light upwards towards the wall at an angle for some accent lighting. There are holes equally spaced apart for securing to a surface via screws or nails. The strips…
These clips are included with the Govee icicle lights, but I don't imagine they will last many seasons (especially in Arizona sun). Rather than order a bunch from Govee I figured I'd model one and print some in ASA.
This is a Govee Non-Pro wall mount. It is used when there isnt a soffet to mount the lights on. it can also be used to mount the light to fences or around handrails or the bottom of decks. There are 4 different sizes 3 inch, 2 inch, 1…
My wife wants to recess her Govee LED strip in the hallway. So I designed this little track to hold it. The center track is 12mm wide, just wide enough for the LED strip to fit. It also has a pair of grooves for mounting diffusion film…
This is a copy and remix of a Thingiverse file by @stage_monkey: https://www.thingiverse.com/thing:5165458 I have included the original 2 files from his link and a remix of my own for LG Oled (very thin only 4mm) TVs. For my LG Oled remix…
I wanted a way to keep the bottom of my curtain lights from moving around in the wind. These pieces hold four 6x3mm magnets and have a slot that the included spaces fit right into.
I needed a mount for my Govee Light Bars that would strap to my monitor's mounting bar since the adhesive wasn't strong enough to hold it to the metal bar with a decreased surface area, so I drew this up quickly. Accepts straps 1 cm wide.…
This is a self made adaption of the new Govee Y Glide. The model has been created with Windows 3D (since I don't master any CAD app). The model is not symmetrical, i.e. the cover only fits one way on the base - so you have to remember the…
This is a very simple model. It's just a tube with a bevel on the top that allows you to position it over the dome of your Govee Permanent Outdoor Lights so you can spray paint them to match the color of your house (or whatever reason…
I bought a Govee H6076 floor lamp a while back and used to lie it flat on top of a desk to get some ambient light behind me when working/streaming. I decided since I was going to fill the wall with Honeycomb Storage Wall plates that I…
