Counting matching models…
Unable to mount a mobile radio in a Tesla Model 3 or Y, I designed this bracket to cleanly and unobtrusively mount a radio head and speaker. Also includes a mic hook. Affiliate links below. Print with 100% fill. Assuming you already have…
This STL file contains a 3D model of an acoustic deflector designed for the internal speaker of the Icom IC-735 transceiver. The purpose of the deflector is to improve sound dispersion, reduce direct high-frequency beaming, and minimize…
Box to two Icom F29sdr radio's. You will need six M3x30 screws to assemble it.
When replacing the broken speaker on my Icom 2100H, the replacement speaker was slightly thicker than the original, such that the speaker and case didn't fit cleanly in place. I duplicated the original design precisely, then made a…
Sicherheitsrahmen für den icom ID-880H Saftyframe for icom ID-880H
I designed a custom 3D‑printed enclosure to house the Icom external keypad project from ON5IA, golb.be , creating a clean, durable, and radio‑shack‑ready finish for the build. The case is dimensioned precisely around the PCB and switch…
I needed a back plate to mount my Icom IC-2730a to a Lido AMPs mount. The stock brackets seem exorbitantly high priced for what they are, so I decided to make my own. Just pay attention that the Lido mount is asymmetric, note the way the…
The Original tips and filaments are great, so these are copied from the above source, with the change to the magnet size and one filament change. Printing Tips Body - Print the body flat at .05mm layer height and used supports. Recommend…
NEW VERSION WITH FRONT COVER IS AVAILABLE HERE: https://makerworld.com/es/models/2585450-icom-ic-705-shield-v2-front-cover#profileId-2852226 Icom IC-705 protective shield. Available as single part or 2 parts for smaller 3D printers. For…
Available two version Basic size with BP-272 battery Large size with BP-307 battery What is need for assembly 8 pieces of M3 x 30mm 2 pieces screw of M3 x 10mm 1 piece screw of M4 x 12mm for TRX fixation Right BNC connector to TRX (…
Unable to mount a mobile radio in a Tesla Model 3 or Y, I designed this bracket to cleanly and unobtrusively mount a radio head and speaker. Also includes a mic hook. Affiliate links below. Print with 100% fill. Assuming you already have…
So, since I have some games that are missing their cases, I took my caliper, measured an original case, and created a reproduction. It is a reproduction because, although I tried very hard to make the 3D printed part fit with the original…
Since the Icom line up of Marine VHF, lacks weather proofing cover I create this simple cover to fit snugly on the M423g. the cover is desgined to be placed on the device when the VHF is not in use, the cord from the microphone needs a…
Camera - Oricom - OBH930PTZ Cot - Mocka Aspen Classic
Replacement cartridge slot surround for Sharp Twin Famicom. File does need supports. I found normal supports to work best instead of tree but obviously FMMV
Increase the intelligibility of received signals with this simple audio reflector. Designed for my IC-7300 and IC-9700. Just place this on top of your radio to reflect and improve audio clarity. If you print with the flat side down then…
Simple stand for displaying a Super Nintendo or Super Famicom cartridge vertically
I have an Icom IC-2730A, which uses an HM-207 mic. I had already created a nicer hanger for my Yaesu mic, but this one has a molded-in “bar” in which you are supposed to hang it from. Being cheap and thin sheet metal, I'm not one to use…
Diskun in coaster form. Included a 3MF, STEP and the original Fusion file. Fits most 8-bit drinks. Importing using the 3MF file should allow you to change color per object.
Jeep XJ 96 and older, blocks off the existing center air vent on the dash.
a cover for the side expansion port of the twin famicom. 2 versions are available, a standard version and a more thin, flush version (seen in pic)
I made these after being fed up with having to try and tape and cut to cover the port covers when spray painting. I haven't tested these with a North American SNES version yet, but I think everything is the same. On the off chance that…
This part will let you replace the magnets on the back of the ID-5100's display with a 1 inch ball that works with ball and socket systems such as Ram Mounts B size arms.
Here's a simple mounting bracket mod made with Nick1's gear cover as the base. uses 3x M3x6 screws and T-nuts.
added the A frame for 4 lanes. I feel it gives more support. Printed the same as Pico parts just because it was already set up
I needed to replace the selector in my Twin Famicom with one without the piece that blocks the cartridge slot from opening so that I could use Krikzz's RGB Blaster for FDS games. There are a few different versions available so please read…
This 3-lane hub is a modification of the orginal from LH's github. It adds in space to install an ECAS bowden tube collet to allow for easy mounting to an existing extruder assembly without modifications. In my case it allows me to keep…
*****update 3/20/24 Added a different hub (G2E Hub v16) that loads better than previous. Reshaped the filament hub to fit into the G2E front body ECAS. Added a mount to the G2E front body ECAS for the Pico filament hub to mount.…
This is a protective cover for the front of an Icom IC9700 or an Icom IC7300 Amateur Radio Transceiver. The front face plates of both of these Icom radios are identical and so for those of us lucky enought to own both, two print runs will…
Easily attach the TNC4 to the back of an ID-52 (Plus) or IC-705. Print Settings These are my experimental settings thus far. Filament: PLA NOTE : T he original clip model suggests using PC Perimeters: 4 Supports: Required on the build…
Simple sifter for dirt/sand that I originally for my wife for her vermicompost (worm composting). Overall diameter 152mm (6") Two cylinder height options, 25mm (1") and 50mm (2"). Two options for the sifter "mesh" 1.6mm (1/16") holes or…
Trivial design that replaces original plate for hanging ICOM HM-210 microphone on a hook with a standard round hanging handle. M3x10 FHCS screw is needed. Edit: Added a lower part to move the handle away from the back of the microphone…
I partially redesigned my lid riser so that after replacing two modules, I could mount a picoMMU. I designed a mount for the picoMMU and a splitter. To make everything work, you still need a runout sensor near the extruder. In this case,…
A simple mic hanger for my Icom-7300. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: .20 Infill: 20% Filament: hatchbox PLA Notes: I used tree supports with overhang over bed only.…
Subaru Overhead Ham Radio Mount (Icom 2730A) Vehicles It Fits: Outback 2015-2017 Possibly 2018 and 2019 as well. Forester: 2014-2016 WARNING: I am not responsible for any damage to your vehicle. This project will permanently alter your…
Based on the wonderfull parametric rugged box, I created the insert to neatly house the Icom IC-20SR PMR radio's and the USB-C charging cables. I added a bit of foam stuck to the lid to keep them from rattling (they won't fall out but…
Legs that allow the RF Deck of the IC-7760 to be placed on its side instead of flat. The legs raise the deck by 30mm to ensure airflow, including to the side ventilation hole. Printed 2x from PETG with default settings. Note: leg is…
Standard IC-7760 stand has quite low angle. Too low for my liking when using control unit on the desk. This is a replacement stand with 110° angle. Stand is screwed to the bottom of control unit (control unit has metal inserts for that…
Halterung für das Icom HM-243LS (Lautsprechermikrophone) Holder for the Icom HM-243LS (Speaker Microphone)
3D Printed case to mount around the iCOMM so it can use a rechargeable battery that can easily be switch out. Build thread and how to can be found here https://www.whitearmor.net/forum/topic/53962-icomm-mount/
I was given an Icom IC-2350H VHF/UHF 50watt radio and I want to make a manpack out of it. However I'm too cheap to purchase an aluminum cage and I own a nice 3D printer. My Fusion360 skills are limited but I'm getting better. This is my…
Common item to break on these great but older radios. I suggest SLA but I'm sure this can be done on FDM, as well.
I printed this in PETG with 100% infill to give strength to the cylinder section in particular, printed on Bambu A1.
Game cartridge for NES FAMICOM DENDY only for a specific purpose
Mix of the ECAS four lane filament hub and the lightguide of the original Orbiter 2.0 filament sensor.
Simple bracket that allows to mount PicoMMU on the top of Prusa MK3/MK3S+ frame. The MMU is mounted by the motor with a single M3 screw. Also provides holes to mount EBB42 board under the motor.
I designed for my ICOM 705 this bracket, for solid antenna holding. Used material was PETG.
Print, add two 18mm disc magnets (under 2mm thick) with cyano glue and you are go!
I needed a slightly modified version of the camshaft since i had only smaller bearings at hand. The bearings are for the selector arm (opposite of the drive wheel) and are 7mm instead of the 8mm of the original design. With those smaller…
The cover of our embroidery machine kept breaking. So we designed and printed replacements.
Pico MMU with mellow fly-ERCF easy v2. Update1.2 Change -Add heat set insert slot at board mount. Klipper only! Connection USB or CAN BUS Input voltage: DC12V-24V Servo pin P21 Filament sensor P20 Encoder P15 Board information firmware…
Simple case for the PicoMemcard/PicoMemcard+ project for the Playstation 1. Will house the PicoMemcard PCB and Raspberry Pi Pico. The USB C port is accessible while in the case. I have use super glue to seal the case, however, this…
Printed on PETG, 0.4mm nozzle, 0.2mm layer height, nothing fancy Used stripped 22awg wire for the pins, enameled wire for connecting to the board RP 2040 Zero should snap fit in the slot SCAD file attached too, I don't know what I am…
This is a mount for Icom 7100 - has built in ball for mounting to an authentic ram clamp (or print your own). It has cable strain relief tabs for the cable sep kit (the cable that comes with it really isn't flexible enough to use with…
80mm Fan Holder for Icom IC-706MKII This is a custom 3D printed fan holder for the Icom IC-706MKII, designed to mount a standard 80mm fan for improved airflow and cooling. It's printed in PETG for strength and heat resistance, ideal for…
A remixed model of Icom IC-705 cover. The original model was designed by KF0ARE. Kudos to KF0ARE.
Halterung für Ladegerät von ICOM Handfunkgerät, mit vier Bohrungen für Schrauben M6. Befestigung der Dockingstation mit zwei Zylinderkopfschrauben DIN 912 M4x30 mit Scheiben und Stoppmuttern. Mountingframe for Docking Station for ICOM…
Halterung für Ladegerät von ICOM IC-A16 Handfunkgerät, zum verkleben auf geneigter Bedienttafel. Befestigung der Dockingstation mit zwei Zylinderkopfschrauben DIN 912 M4x30 mit Scheiben und Stoppmuttern. Mountingframe for Docking Station…
Here is my version of Icom IC-7300 Keypad. 4 memo. Knobs used from aliexpress shop: https://a.aliexpress.com/_EHrIWoA Projet can be copy in thinkercad:…
SicherheitsRahmen für das Icom IC706mk2g Amateurfunkgerät. Um dieses beim Transport vor Schäden zu schützen. 2 Teile müssen gedruckt werden und man benötigt 4 Senkkopf Schrauben M5x12 um die Teile zum montieren.
Updates 19-04-2023: First upload Usage Having a small vermicomposter can bring many benefits to your home. First and foremost, it's an eco-friendly way to dispose of food waste. Instead of throwing away scraps, you can feed them to the…
Zoe Phase 2 (from 2019 on) holder for ICOM IC-2730 print in PETG.
I designed a mount for the Icom iC-2730A because the manufacturer no longer supplies it with the radio, only as an accessory. I printed it on 3-wall PETG with 15% infill. I hope it's useful.
the original used PC4-M6 thread so remix to use PC4-M10/01 thread
Bottom cover for the ICOM IC-A20 for use without a battery. Two versions provided: ica20-cap-supports.stl : version with hand-crafted supports ica20-cap-nosupp.stl : no built-in supports The cap slides and clicks without play. Use a 0.4…
Case diseñado para organizar 6 cartuchos de Nintendo Famicom, puede usarse de manera vertical u horizontal, es apilable en ambos sentidos
Dustcovers para cartuchos de Konami para Nintendo Famicom, NO FUNCIONAN en otras marchas de caruchos (Jaleco, Bandai, Genericos)
🕹 Stackable Pal Super Famicom Game Storage – Support-Free Print with Dust Covers Organize and protect your PAL Super Famicom / SNES cartridge collection with this custom-designed, stackable storage system. Each unit is designed to hold…
Alternate servo mount & belt gear for MG90s servo. This servo seems to be more readily available and is quite compatible with EBB42 board given the current and voltage ratings.
The modified box will allow you to transport everything you need for portable operation with the IC-705 transceiver. Antenna, power bank, USB-C power delivery adapter, headphones, antenna , telegraph key, etc. Since the bottom part is…
I found this mount listed for the IC-2730a ( https://www.thingiverse.com/thing:4879947 ) and shaved the base in Tinkercad. I have both the IC2730a and the ID-5100a and can confirm it fits both radios. It may fit others that take the MBA-2…
This is an interface plate to put your XPA125B on top of your Icom IC-705 if you already have a Windcamp protective shield . a stand in the back of the xpa125 will hold it in the same angle as the 705. There is also a little enclosure…
I made two variants. The simple one is only a rail for the left and right side (use same file just twice) of the Radio. The second one does support a ground base for the radio (radio sits on top). This will be used as for a stackable…
Nedded several stands for radios onboard a vessel. Designed this in fusion to be a snug fit to make sure the portable radios is secured properly with no chance of accidentally falling out, even in violent vibrations and 90 degrees…
This is a vertical stand for the SNES or the Japanese Super Famicom. It is not compatible with the US SNES OnShape Model…
This is an adapter for the Nintendo Twin Famicom expansion port A. It is compatible with NES and SNES controllers, plus the NES Zapper lightgun with the 2P NES port. ===Printing=== Print everything facing up is a good choice. There really…
Here is my design of an expansion to connect NES and SNES controller to the front port of a Nintendo Famicom. It makes the Famicom look like a Countach in the front. Hence the name of this project. The player 2 NES port supports the…
Famicom front expansion port cover for those who lost the original. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.15 Infill: 10% Filament: Polymaker Polyflex PLA/PETG Dark Red Notes: I…
The Nintendo Famicom has been nagging me for almost my whole life with its non-detachable controllers and awkward length of the cord. So here is the solution to scratch that itch. 3D model slicer examples as shown in the pictures for best…
Klickfast Adapter für ICOM ID-51 und ID-52, der direkt auf der Batterie montiert wird. Anstelle der Originalklammer wird dieser Adapter direkt auf die Batterie aufgesetzt
This completely replaces the power connector assembly meaning this mod is reversible (although it probably voids your warranty). Parts needed: 2 M3x10 cap-head screws 2 M3x5x4 heat set inserts 2-pin Powerpole connector with cut-to-fit…
This LED mod for the PicoMMU (4-lane) was inspired by @marcribe's model, except it was created from scratch and uses friction fit to stay in place above the lane modules. For the main parts, i recommend Voron settings and ABS/ASA…
https://www.thingiverse.com/thing:3569530/ Remixed the VESA mount to work with the faceplate of an Icom 5100 radio. This mount will work with the Articulating Arm here: https://www.thingiverse.com/thing:2448971 Shown in pictures with the…
MiSTer FPGA Famicom Expansion port SNAC Adapter Shell with logo Snap-fit enclosure, four versions with different logos. clean - no logo ff - simple Famicom Family logo famfam - Famicom Family logo with "Famicom Family" text mr - Diskun…
I use Multicomp filaments a lot for my prints. Some of these filaments come in cardboard spools. As the spool rolls on the spool holder, its central hole gets damaged and cardboard shavings land on the printer. This adapter can be…
Just a logo. I should have printed with more infill. Made to go on top of my soon to be famicom game shelf. Category: Signs & Logos
