Counting matching models…
Fridge/Freezer support peg for old Kenmore/Whirlpool fridge/freezer models. My unit is a side by side, not sure if it works on other models. Picture of the fridge is the model I have. Picture without model is what it slides over. It is a…
Replacement gear for a Kenmore 158 series Hook Drive Gear. Traditionally made with nylon they can crack over time. My sew machine is model 158.18800. Make sure the mark the orientation of the needle and the bobbin holder. I had to…
This device pushes the lower follower to the extreme right position. To use, put the dial on the CAM setting, push the follower release lever to the right, and insert the device with the upper follower in the hole. The needle will now be…
Replacement door latch for an old kenmore dishwasher, might be able to be modified for others as well because it is a common design. Must be printed in ABS or nylon to hold up to the high heat. Supports needed Print Settings Supports: Yes…
Jarrik made fantastic model and deserves full credit. I just made it big enough to fit the Kenmore Pro Oven Knob that is no longer available to buy.
This small part supports the bottom drawers (often referred to as "crisper drawers") for many brands of Refrigerator. I'm using this in a Kenmore, though cursory research suggests the same part is used in several other models. The small…
I was sick of my attachments falling off the mount for my vacuum. I designed a simple offset to give it a more secure fitting.
Sewing machine didn't come with the case or portable base so made one up to make sure the machine doesn't tilt over while working with it. Not sure what other machines this will fit, I know it won't work on the 1720 (new design for that…
The release nubbin on our washing liquid tray wore down and no longer latched. This glue-able collar raises the clasp and adds some structure to the bottom side of the original part. You could also repair this with building up a profile…
This attachment makes turning the handwheel a one-finger operation. It's held on with 20 1/4" cube neodymium magnets. I put a small square of masking tape on each magnet to help with grip on the polished chrome handwheel.
This plate allows the user to position the needle for straight stitching. Use the CAM setting, insert plate, and then use the width dial to put the needle where you want it. I tweaked a previous model and the print is a little ugly, but…
The pin that holds the drawer down was broken. Unfortunately Kenmore built this to have the entire plastic side as one giant part. Seeing as only the pin was broken, I quickly designed a part that wedges over the broken tab. Not sure what…
Replacement gear for a Kenmore 158 series Hook Drive Gear. Traditionally made with nylon they can crack over time. My sew machine is model 158.18800. Make sure the mark the orientation of the needle and the bobbin holder. I had to…
This part adds a reduction pulley to the Kenmore 158.161. I suspect it will work on similar models like the 158.540. The mount uses a pulley from a Kenmore 158.12511. This pulley may also be found on models 158.12510, 158.12512, 158.12520…
These ugly old Kenmores are cheap and unloved, but built like a tank. This Bigwheel clamps on the original handwheel and makes sewing thick fabrics much easier. You must remove the bobbin winder assembly and cut off a small part of the…
This device pushes the lower follower to the extreme right position. To use, put the dial on the CAM setting, push the follower release lever to the right, and insert the device with the upper follower in the hole. The needle will now be…
Our old Kenmore refrigerator drawer rail broke. The cheapest one I could find was ~$50. This has been installed and used for over a year now. Print on the flat side out of ASA. The retaining pin does require a support.
This is a shelf support for a Kenmore Fridge/Freezer. Specifically this is the rear support. I printed in PETG.
I used measurements from a damaged OEM part to create this printable version. I iterated through a few printed versions until I got one that worked well enough for my purposes. It's a bit finicky in that you can crack the screw posts if…
One of the clips on the original washer door plunger broke so I created this replacement. Keep the original spring and free the magnet from the original plastic piece (challenging) or use a few 15mm or so neodymium magnets stacked. To be…
Older Kenmore refrigerators with the freezer on top have a ‘cold stream’ in the back center of the refrigerator that will freeze any food pushed into it. This clips into the rail in the back of the fridge and prevents stuff from being…
Get one of these already-printed at https://superherodiy.com/products/replacement-button-cap-compatible-with-kenmore-washer-dryer This "soft" button on our front-loading Kenmore washing machine has been breaking down for the last few…
This works for many different models of Kenmore canister vacs back to at least the 90s Kenmore Progressive vacs and most likely beyond. PLA 5 walls 3 top and bottom layers 25% Infill Most likely overkill, but its held up very well.
This is a replacement button for the Crisper Drawer of a Kenmore / LG refrigerator. The pivot pins broke off on the original button after 10 years of use so I designed this; it works like a charm. The button is designed to fit Kenmore…
print if you lost yours, like i did! Category: Replacement Parts
This is a replacement for our dishwasher, maybe it could help someone else. Note: Not tested yet, still printing, tested the threads and they fit. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.1…
Printed connector side down, normal supports (snug). Filled in the holes with paint using a fine paintbrush and went over with an epoxy finish over the whole knob. Design will be improved upon whenever I have the time.
This is a replacement bracket for the bar that secures items on the shelves of the door of my very old Sears Kenmore freezer. Parts for that freezer are essentially unobtainable. Based on my research, I believe this will fit some older…
Still a bit of a work in progress My mother gave me an extra sewing machine (Kenmore Ultra Stitch 8) she had but it was missing a working extension plate. So I modeled the one that she had to make an almost exact copy. You will need to…
UPDATED .STL FILES FOR BETTER FIT 06/30/16. TWO NEWER VERSIONS, BETTER FIT. I have a Kenmore 106.72153111 23 CUFT refrigerator in stainless steel. I has nice brushed aluminum handles, but one end (of each) has a poorly designed gray…
Replacement door latch for an old kenmore dishwasher, might be able to be modified for others as well because it is a common design. Must be printed in ABS or nylon to hold up to the high heat. Supports needed Print Settings Supports: Yes…
The locator tabs on the momentary switch that controlled the water for my fridge were broken, so the switch wasn't in the right spot. I designed this to snap on to the existing framework of the dispenser. If you need it for the ice side,…
This is a replacement wheel for the Kenmore Whispertone Vacuum. Specific measurements were taken specifically from a model 12.0, but it may fit others. This piece fits into the rubber edge from the original wheel. I wasn't able to get…
Just a simple knob to replace a number of selector knobs that broke over the last 20 years on my Kenmore washer and dryer. Print and remove the exterior perimeter wall, as it is just support for the knob top. Category: Replacement Parts
Apologies for the gross picture - our dish detergent leaves a terrible residue buildup over time, but i digress… One wheel of the lower rack on my dishwasher had completely broken off and another was in bad shape (I have kids). I tried to…
I couldnt find any replacement door handle endcaps for my Kenmore Oven (Model # 911.95589991 ) So I designed and printed these. This model makes use of the factory mounting screws and includes the two indexing pins. I reccommend printing…
This model requires a build volume of at least 220mm X 220mm X 220mm. The print orientation of the ShelfBracketV2_ReadyToPrint.stl file will provide an optimal print strength as the the bracket will be subject to stress, when installed in…
This was an ad hoc creation to fix the wheel connector on the upper rack of a Kenmore dishwasher model 665.13223N41. This IS NOT a factory replica or does it resemble anything that probably went there originally. I looked at the holes and…
I took measurements of the fridge door features that interface with the bracket and tried to reduce the design to its simplest parts. The result is a design that I feel is both simple and appropriate for FDM printing. Brackets were…
Got this kenmore fridge for free but it was missing some stuff. The main door shelf had only one clip and nothing to fit into the clips. We had some pvc laying around (measured about 27mm in outer diameter) and so I made a quick…
The motor coupling on my washing machine failed. I found the rubber center section from this 285753 Motor Coupling for Whirlpool Direct Drive Top Load Washer by OnShape - Thingiverse and printed in TPU, but then discovered that the…
Jarrik made fantastic model and deserves full credit. I just made it big enough to fit the Kenmore Pro Oven Knob that is no longer available to buy.
After our dishwasher detergent door latch broke I looked to replace the latch, only to find that the part was only sold as a assembly... A $105 assembly.... So... 30 minutes of design and 30 minutes of printing later it was fixed, and if…
This small part supports the bottom drawers (often referred to as "crisper drawers") for many brands of Refrigerator. I'm using this in a Kenmore, though cursory research suggests the same part is used in several other models. The small…
Overview Replacement 3D printed foot release pedal for Kenmore 116-series upright vacuums. Designed as a durability-focused FDM translation of the original injection-molded part, with thicker load paths and smoother stress transitions.…
Replacement timer knob for Whirlpool-family washing machines. Designed as a direct-fit solution for discontinued or hard-to-find OEM parts. Personal use only. Commercial use, resale, or redistribution is not permitted.
I was sick of my attachments falling off the mount for my vacuum. I designed a simple offset to give it a more secure fitting.
Replacement capacitor holder for the Kenmore 110 (and potentially other) series washing machines. The OEM capacitor is overpriced, and you can get a BlueStars branded replacement capacitor for around $10 on Amazon. For my Kenmore…
The rather complex clip found (broken, of course) in the lower rack of a Bosch dishwasher. Printed in PETG, with 0.2mm layer height, at least 4 perimeters (so practically solid), and 30% gyroid infill for good measure. Due to the tricky…
Replacement brackets for large shelf door on Kenmore Refrigerator (Model # 363.9669611) Orient the parts on the bed as shown in the photo of the 3D Prusa printer. Use supports from bed only. Print 0.2 mm layer height. 15% infill. PLA…
Replacement start button for a Kenmore Dryer model: 110.87572601. This has pops into place and is held only with friction. I took a knife and trimmed around the opening since there was a small amount of the outer original plastic covering…
Both the front and back rack mounts for Refrigerators manufactured by Whirlpool including KitchenAid and Kenmore
Why spend $2 plus shipping when you can print your own replacement part? After we moved in to our new place we found the range vent was missing the baffle plate blowing all the greasy exhaust air back in the kitchen. Found image with…
Vibration guard connector broke on my Kenmore washer so made this to replace the OEM.
This is a 3D rendering of the famous Massachusetts Bay Transportation Authority (MBTA) or “The T” subway station sign. The Fenway Park subway station sign that leads to the home of the Boston Red Sox.
Quick replacement hub for a Kenmore Magic Blue vacuum. Fits well enough to let the wheel turn, though not as flush as factory. Held on with four short panhead screws. Category: Replacement Parts
This is the rear slide for a Kenmore oven warming drawer. If your plastic slide breaks and you don't want to spent ~25 for a new one that is made of $0.08 of plastic, this should get you going. Print in a vertical orientation with…
If you found this, you probably have the same problem I did… The OEM bracket is poorly designed to withstand day-to-day forces over a long time. The first time I replaced the bracket at the cost of $90, because Sears will only sell it…
This is yet another oven knob model. I couldn't find an existing model that matched the one I shattered. The model was created in FreeCAD 0.20 and exported to .step format. The FreeCAD file is included in case you want to remix. I sliced…
This is an adapter to connect the Kenmore Crossover Max vacuum hose to fit a 1.25" attachment. Specifically this was designed and only tested for fit on the "Under Fridge Cleaning Tool Flat Vacuum Attachment" on Amazon , but may fit other…
Replacement for the inside mount of the freezer rack holder. I added a little outside ledge to it to allow the freezer rack to move back and forth a little without allowing the rack to fall down as the factory model did.
replacement wheel for a kenmore vacuum cleaner. this part is just the axle, wheel part to come later
Replacement clip for Kenmore (Sears) freezer model Model 253.9206381 Printed with PLA, no brim or supports are required. Used a 20% infill.
I realized the gasket was missing on our dishwasher's detergent dispenser, so the detergent was always leaking out when the dishwasher door was closed. Rather than pay $40 to replace the whole dispenser, I printed a gasket for pennies.…
We occasionally like to eat a meal with chopsticks. Unfortunately, our Kenmore model 665 (circa 2008) dishwasher has a utensil basket with holes big enough to let chopsticks drop through and interfere with the water sprayer below. Because…
A friend needed a replacement bracket for her Samsung freezer. This is the result. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20 Filament: Generic PLA White Notes: The two parts…
0.2 layer height, PETG or PLA, no supports are nessecary for the shelf bracket BUT are nessecary for the bracket arm
Replacement for a broken knob on Kenmore range hood. Print with supports. Note: I used 101.5% shrinkage compensation for PLA, adjust accordingly if dimensions slightly off.
Sewing machine pattern cam for 1964 Kenmore 158.650. Basic Zig Zag. This may fit other Kenmore sewing machinemodels. After finding that replacement parts were just too hard to find, I decided to just make one myself. The blueprint is…
This is a replacement handle for a Kenmore microwave. The part number is 3650W1A075H but it's been discontinued. I've included the .stl file for the handle and also a base to which the handle can be attached for sanding painting. The base…
Replacement wheel for Kenmore vacuum cleaner. I printed the wheel itself in PLA+, the tensioner out of TPU at 10% infill, this part is inserted into the middle hub. I printed the tire out of TPU 95 with fuzzy skin enabled. Included a…
Flipper of Kenmore French door refrigerator (Model No. 795.71313.310) is prone to failure due to weak part (the failed plastic was lost but I think this may be better than gluing the shattered plastic back together). You can hot glue this…
While moving my Whirlpool dishwasher to a new home, I lost one of the rear “transport” wheels. They are also used to adjust the rear height, function as the rear feet, and appear to be used on a number of different brands (Whirlpool,…
I'm not sure who this will be helpful to given that this drier is absolutely ancient, but a repairman I had fix an unrelated issue with the drier quoted us 50$ for a replacement for what amounts to about 10 cents worth of plastic so I…
The Kenmore 158.1703 sewing machine has a left homing needle. These plates allow the user to have a Center-Homing or Right-Homing Needle instead of the factory default Left-homing. To use, select the CAM position and set the stitch width…
This is a replacement for the button on a Kenmore clothes dryer, which is now obsolete and the part is hard to come by. I made some modifications to it, such as reinforcing the inner wall and joining the part of the base with the part of…
I often find I never have an oversized Pirate Ninja Star when I need one. And if you print this Kenmore Freezer Drain Screen (which replaces Kenmore part number 253.23429100) at, like, 250% or larger, you will, indeed, have yourself a…
This mod for the handwheel gets the speed down, torque up, easier to control speed with pedal, easier to turn handwheel, still fits in cabinet, still sews faster than I can, sews all the denim I can cram under the presser foot. This is a…
The Kenmore 158.1703 has a small handwheel that some find painful to use. This bolts in place of the original and uses the original screw to hold it in place. I've made it a tight fit, so be prepared to scrape and sand it to get a perfect…
This C Cam 20 is required to do the reverse stitches in some Kenmore sewing machines. They are often lost and hard to find. Now you can print a bunch and lose all of them you want. The hole will be a little tight. Wrap some sandpaper…
With my center-homing 158.1756 Kenmore there was no way to select a right position for the needle. Use this and set your machine to the CAM setting and the ZZ width to the maximum. I used PLA+ Four layers and 50 percent infill.
The light shield in this refrigerator is held in by two screws. The left mounting hole cracked leaving the shield mount sagging and spinning. This replacement is printed in three parts to fit smaller 3D printers. The original piece had…
Our fridge is not that old but a few months back the big door handle broke at the top in its thinnest. I unscrewed it, fired up Fusion360 dug out calipers, and got to work. Then, I printed it in white PLA at 0.2mm layer height, sanded it…
This fits a Kenmore dishwasher, model 363.1404596 (may fit other models). It is designed to fix or replace the studs that fit into the upper dish rack rail runners. These parts retail for $20+ so I took an hour and 2 test prints to design…
Replacement for the plastic cap in the pulsator/agitator. Tolerance fit, so size up if need be.
Older washer get off balance and break the lever going to the lid switch? This is a replacement lever that wraps around the switch just like the original and actuates when the lid is closed. Pictured are the original parts and the printed…
This is just the outer ring for the time setting knob on a Kenmore 80 Series dryer. My dryer sits by a window and the knob has been damaged by the sun, while the ring completely crumbled apart due to sun damage. I will need to build the…
This is a clip-on patch for the retainer bar used in the Kenmore 253.68802014 refrigerator. The bar's OEM part # is 240534901 and it appears this is also used by various other makes (Frigidaire, White-Westinghouse, Crosley, Kelvinator,…
I needed a replacement handle for our Kenmore microwave, model #40185049210 and did not want to pay over $60 for one including shipping. So, I took some measurements of the old one, and had one ready the next morning ready to put on! I…
This is a temporary plug for the gearbox in a Kenmore free arm sewing machine. I made it for a 158.1941. It may fit other models. I made it slightly oversize so you may need to sand it to a perfect snug fit.
The plastic wheel hub was disintegrating after years of use but this new piece printed in PETG seems to be holding up well so far. It has fixed the wobble that we were seeing when the wheels rolled across the floor. I printed this with…
Sewing machine didn't come with the case or portable base so made one up to make sure the machine doesn't tilt over while working with it. Not sure what other machines this will fit, I know it won't work on the 1720 (new design for that…
Oddly my Kenmore Microwave didnt come with feet so I made them. Settings Layer height: .2 Supports: yes Filament: PLA+
A replacement foot for my old Kenmore model 158.12310 sewing machine. The internal structure that this foot mounts to is partially continuous with the cast metal frame of the machine casing, so it requires a cutout in the coupling collar…
I made these for my Kenmore 158.1913 and 158.1941. They fit on the push/pull clutch and make it easy to turn the handwheel. The two parts clamp on the handwheel using two screws, but the grip comes from several small pieces of removable…
A Kenmore 1A-1B pattern sewing gear compatible with models 158.15x, 16x, 52x, 54x, 64x, 65x, 85x, 1503x, 1649x, 1653x, 1749x This is a common gear to be lost when finding and salvaging used Kenmore sewing machines. Printed on a CR10 with…
This part replaces both the steel hub and the nylon cam and integrates it into one unit. Print it so that the center hub is an easy slip fit on the mating shaft. Otherwise it will be hard to get it in place inside of the sewing machine.…
Only replaces the spring. Keep the rest of the release lever.
Replacement Dryer Feet (Kenmore/Whirlpool ) In case your old dryer feet break during moving or cleaning this quick 1.5hr print and your good to go! Can be used to replace a variety of dryer feet from brands such as Whirl-pool, Admiral,…
Needed a shim to raise my freezer door up a bit. Used pliers to place this between the nylon washers. Those will adsorb the movement not this shim.
