Counting matching models…
This caliper helps with sizing a tenon when using a Oneway Stronghold Chuck with #2 profiled jaws. On one side is the minimum diameter of 1 3/4" and the thickness is 3/16" which is the minimum length for a tenon, and on the other side…
This caliper helps with sizing a tenon when using a Oneway Talon Chuck with the standard #2 jaws. On one side is the minimum diameter of 1 5/8" and the thickness is 3/16" which is the minimum length for a tenon, and on the other side…
This caliper helps with sizing a tenon when using a Oneway Stronghold Chuck with #4 profiled jaws. On one side is the minimum diameter of 4 1/4" and the thickness is 3/16" which is the minimum length for a tenon, and on the other side…
This caliper helps with sizing a tenon when using a Oneway Stronghold Chuck with #3 profiled jaws. On one side is the minimum diameter of 3 7/8" and the thickness is 3/16" which is the minimum length for a tenon, and on the other side…
Several pieces that enables wall mounting of the OneWay EasyCore knives. These should be printed out of PETG or similar springy material (PLA won't work well).
I sometimes want to mount my bowl or vase on the lathe in reverse direction for sanding or light finishing touch-up but I want to keep the alignment of the chuck that is still mounted. I then drive the bowl with a soft prop chuck and…
I recently got a OneWay EasyCore system. It is lots of fun but there are a lot of pieces! I wall-mount as much as possible in my small turning space. This bracket stores all four of the EasyCore fingers (rests) in a single, compact,…
One Way street sign toy. For City playscape. I printed it in 2 colors, Black and white. It should be sturdy enough for play. 0.20mm layer height Wall loops 4 5 top and bottom layers 20% Infill.
This design fits over the cutter of the OneWay EasyCore coring system. It will protect the cutters from banging around (and your flesh from the sharp edges!). Recommend to be printed in TPU or other similar flexible filament.
Advice 1/rada 1: Print side_A with normal support. Na side_A jsem použil normální podpěru kvůli drážce, kam se pak zastrčí dvířka. Advice 2/rada 2: Stick traffic signs after placing door inside side_A. Značky přilepte až po tom, co dáte…
2 inch includes internal void for inserting 15x22 magnets from Hobby Lobby (US). Wings on handle end are just to allow better handling. 2-3 is has same but for both the 2 inch standard jaws and the 3 inch dovetail jaws. Magnet is in the…
Minimal through-bolted mount I designed for my Robust live center and ring drive center attachments… https://www.turnrobust.com/product/live Also fits similar ¾-10 centers by OneWay, Savanah, etc. The weight is on the through-bolt or wood…
you need: 5 one way bearings (CSK8PPT type, 8x22x9mm backstop cluch - cost $ 1.85 x 5) - https://www.aliexpress.com/item/33040222926.html print 10 body print 5 tyres for the bearing 5mm width rubber band (to put on the tyre for grip). You…
We let our cats leave the house only on certain conditions but let them come back whenever they want, So i've designed this modification to replace the original “Top” part. Print and install all the other parts as in the original. The…
It's a simple jig for marking the right size to cut, so that a tenon or recess works well with any of the Oneway Stronghold jaws (except for #4, which never made much sense to me as they overlap with #3 too much). It works for both…
Čelisti standardně dodávané se sklíčidlem ONEWAY TALON mají minimální průměr vnějšího upnutí okolo 40 mm. Pro menší obrobky lze použít tyto čelisti. Samozřejmě s rozumem a citem, je to plast, tak jen pro lehké kousky. Jak šrouby čelistí,…
a small controller for sirens (Was made mainly for JNPrinting's Federal Signal 2001 SRNB (Fully Functional) or any siren
Hourglass-Cap for the injection-molded prusa holder . You can make this hourglass work by putting a little bit of sand (preferably fine, rounded) inside. To close it, you need to glue an acrylic disk (40mm diameter) on top of it. (e.g.…
