Counting matching models…
🌀 Peristaltic Pump (NEMA 17) This is a compact, fully 3D-printable peristaltic pump designed to be driven by a NEMA 17 stepper motor . The pump uses standard 608 bearings and soft tubing, making it easy to build with commonly available…
Version 2 out now in a remix ---> All you need is a Nema 17 motor, 4 x 608 bearings and some 8mm plastic Tubing (Soft tube needed). You will also need some 16mm M3 screws to attach the pump assembly to the stepper motor. Of course the…
All designed parts of the peristaltic pump are printed out of PETG. For the hose I have choosen silicon to avoid high forces by rotating the impeller. The hexagon shaft where the impeller is put-on have two interfaces, on one side an…
Pumping gear oil by hand is frustrating, use this instead! Chose a quality “engineering” material for best results. I used a Saturn 3 resin printer with Siraya Tech Blu Tough, in Easy Grey. Some tolerances are relatively tight, I highly…
This is a 3D printable model for a peristaltic (aka hose) pump for either 3mm or 4mm silicone hoses operated with the popular and cheap 28BYJ-48 stepper motor. The motor is usually sold with a fitting driver shield and there are various…
3d print a simple waterpump! This is a peristaltic waterpump with high pressure and low waterflow. I used it in a small automatic greenhouse where it connected to a spray nozzle. Hardware required: Yellow TT-motor (ideally low rpm and…
Plants need fertilizer. Manual dosing kept me doing to much or too little with results accordingly. The pumps feed liquid fertilizer into the irrigation system while watering. Dosing can be adjusted on a very wide range. A lot of…
as i only had 608 ball bearings, i created my own peristaltic pump. It is to be used for dosing fertilizer solutions in the hydroponics sector, but will certainly also work in other areas. - All the screws required are M3. - The silicone…
BOM: Note: incomplete, haven't had time to check exact fastener lengths: Bearing Assembly (Non-Print in Place Version): 1x M3 bolt + nut 3x M4 bolts + nuts 3x Needle Roller Bearings (4mm Bore Dia, 8mm OD, 8mm Width) Other: Silicone Tubing…
Based on off_grid_craft's design ( https://www.thingiverse.com/thing:3445927 ). These motors are small and cheap and will stall if the pump is run too fast. Produces a very slow, precise and reliable flow rate. I have mine operated by an…
A din rail mount for a Peristaltic Pump. The pump we used: https://a.co/d/fWMLnrs You will need to print two tabs for this design. They can be found at: https://www.thingiverse.com/thing:3401942 or…
Parts: printed parts (see .stl) 5x 608 bearing hose silicon hose Ø6/4mm | length: min. 1m recommended fixing elements 3x cylinder screw M4x25 2x cylinder screw M4x15 5x hexagon nut M4 4x M3x10 Printing: Material PLA Infill 25% infill…
This is a nice little precision pump and controller combination. It can dispense 100 ml/min at 300 rpm. I set the output to 1 amp and use 16 micro steps (set dip switches to 16 and F09 to 160). I use working mode 3 (F01 to P03) and a low…
This pump is a perfect project to reuse the NEMA17 stepper motors from an old 3D printer like ender3, prusa MK2 etc. IMPORTANT: All parts should be printed using PETG or ASA, especially if you run the pump of longer intervals. Using PLA…
Used https://www.thingiverse.com/thing:454702 to get a working pump and added holes to make it compatible with lego technic. I've been using it with 6mm silicone aquarium tubing to pump small amounts of citric acid into a baking soda…
Full build details here Peristaltic pump with two flow channels, each of which capable of flowing up to 5 liters per minute, although recommended continuous flow rate closer to 2 liters per minute. Initially designed to be used with an…
I present my peristaltic pump for watering flowers on the balcony based on the engine from the Ford Scorpio ABS pump and a hose 8 mm (inner diameter) / 10 mm (outer diameter). I printed the pump from PLA because its elements do not come…
My first attempt at a 'budget' dosing peristaltic pump, mixing some design concepts together from some previous, related designs. You can find more info on the design, and I will be continuing to add related designs, here. One of the main…
I made these pumps primarily to test something else where I wanted to use peristaltic pumps, but needed fine control...I also just was curious how hard it would be to make a printed peristaltic pump :) Turns out, not too bad! I used 3/8"…
A din rail mount for two Peristaltic pumps and a stepper motor to drive a mixing padel. The pump we used: https://a.co/d/fWMLnrs The stepper motor is a standard NEMA 17. You will need to print two tabs for this design. They can be found…
Parts needed: 4x 36 mm or longer M6 bolts with hexagonal heads 4 wing nuts for the M6 bolts 1 drive bolt (M6). Should be longer than the others 4x 608-style bearings Silicone tubing ~5mm ID (or smaller ID) and 10mm OD. Assembly: Push the…
A custom-sized holder for a peristaltic pump, designed for mounting on a compatible pegboard (link provided). The holder features a slot for a 15EDGVC-3.5 connector, ensuring secure and organized integration with the pump. Made from…
This pump is designed to work with a servo or simple DC hobby motor. It requires additional components including: 3mm ID/4mm OD Silicon Tubing (like this https://www.amazon.com/dp/B06W2JW633 ) 3 Ball Bearings (4mm X 13mm X5mm…
Hose retainer for dual hose Peristaltic Pump Video: Print Settings Supports: Yes Resolution: .15 Infill: 100% Filament: Generic PETG , PC Category: Tools
Replacement peristaltic pump for GatGenie. Onshape Project Filament: https://amzn.to/4gpUqB6 Print Settings Printer: 3KU 3000 Rafts: No **Supports:** No Resolution: .1mm **Infill:** 100% Filament: NA ABS NA Notes: Print in ABS for…
🌀 Peristaltic Pump (NEMA 17) This is a compact, fully 3D-printable peristaltic pump designed to be driven by a NEMA 17 stepper motor . The pump uses standard 608 bearings and soft tubing, making it easy to build with commonly available…
Needed a plate mount for a 12V peristaltic pump. In this case 48mm bore mount distance.
This is a simple peristaltic pump I designed. It uses a 755 motor and 608 bearings that fits 3.2mm Bore Size Silicone tubing. The motor is mounted into the rear of the frame using M4 screws, The bearings and bearing mounts are friction…
Tate's original worked great for SLA, but the rotor peg melted on my FDM version, so I modified the rotor to remove the peg and replace it with another 1/4in bolt. Both this new bolt and the original drive bolt will fit without…
500ml/min Lift=5m G928 Large Flow Peristaltic Pump 24V https://www.aliexpress.com/item/1005005712663786.html DC 24V/2A Transformer Power https://de.aliexpress.com/item/1005005553964246.html
Replacement peristaltic pump for GatGenie. Onshape Project Filament: https://amzn.to/4gpUqB6 Print Settings Printer: 3KU 3000 Rafts: No **Supports:** No Resolution: .1mm **Infill:** 100% Filament: NA ABS NA Notes: Print in ABS for…
This is another variation of peristaltic pump. I used HS-755MG servo whose electronic was broken and connect power supply (5V) directly to the motor. Next "vitamins" is 6pcs of 625 ball bearing, several M5 screws and nuts, M3 threaded rod…
This is a complete re-engineering of the excellent design of Ralf's Perstaltic pump. I printed his pump and built it to his specs, but I found that the small stepper motors would not really run the pump consistently or with enough power.…
This is a peristaltic pump designed around 4/6 mm silicone tubing and driven by a JK42HS48-1204 stepper motor. I printed the parts in PLA for testing — works fine so far, but long-term durability hasn’t been checked yet. BOM The model…
Print Guide: no supports! PETG! 0,4 nozzle 2 Walllines, 15% Gyroid infill This mount was specially designed for the AC Infinity Peristaltic Dosing Pump. Instead of placing the dosing system in an improvised way, you can attach it securely…
I needed a peristaltic pump and ended up with the G528 (amazon). Works fine for my purpose but with the bare wires I wanted an enclosure. Printed for a CoreOne I designed it with .15mm tolerance for the lid. No idea if this is a generic…
Slightly thinner stems on the bearing mount, and shorter housing, closer the to motor. So more of the motor shaft is in the bearing mount
A compact peristaltic pump powered by a NEMA 17 stepper motor. A press-together stop (fastened with a few dabs of super glue) prevents the tubing from shifting during use. STEP and STL files are included. Update : New roller head and pump…
Remixed from milks' design, who further remixed it from off_grid_crafts . The cover and motor are now independently mounted to the pump body and the roller track has been slightly modified. STEP and STL files are included. Update : New…
This is a peristaltic dosing head with a reversal dampener. It uses a 9:1 gear ratio and a nema 14 drive motor. This is a part of a series of experiments I am performing on liquid/farm bot/bio related devices. Videos:…
I designed this simple mounting system for the Yosoo 6v Dosing pump I got from Amazon .(https://www.amazon.com/gp/product/B00HLCOXFI/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1) I Printed With PETG and am truly amazed at how strong this…
Made to hold a 2in diameter peristaltic pump (specifically this one https://www.thingiverse.com/thing:454702 ) and a 775 drill motor. Includes and adapter from the motor shaft to the pump. Also has fittings for m3 nuts to be inserted so…
This is a remix of the peristaltic planetary gear with lots of improvements baked in. Most notably, this pump mounts directly onto a NEMA 17 stepper motor. It also opens up using a hinge to allow the tubing to be easily loaded into the…
UPDATE 2021-04-30: Added a simple cap to cover the motor terminals. This is a wide mouth Mason jar lid with mounting holes for a cheap 12V peristaltic pump. I will use this as part of an automated container garden. The pump I used is…
It prints as a single piece. The only non-printed part is the tubing. can be driven with a standard nut driver bit or a ¼ hex key this is a remix of this Parametric Peristaltic Pump which is a remix of this Gear Bearing
This is a simple holder for a 5x7cm prototyping PCB with holes for a potentiometer and a LED. For the pump I used the design of silisand ( https://www.thingiverse.com/thing:1134817 ). The schematics of my circuit can be found in the…
Developed for my PhD work. This is a peristaltic pump driven by a Nema-17 or alike motor using an Arduino (nano or alike) and EasyDriver. Files for the wiring layout and Arduino code are included. There is also a table that contains the…
Long story, not so short. I have a resin printer, and I use IPA to wash my parts before curing. After a while, the IPA accumulates a decent amount of uncured resin (ewe). I found this video where they use Aluminum Sulfate to coagulate the…
I made this peristaltic pump to test water cooled parts, it uses 11, M3 screws, 3 small bearings, silicon tube, 1 DC motor and 3d printed parts. It can pump about 22 mL of water per second with a 4S battery. Motor (I used 12V 550rpm) -…
Simple holder for peristaltic pump which can be obtained on Ebay/AliExpress. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Category: 3D Printing
This is a housing for a pump. I created this so I could move isopropyl alcohol from a container to a filter set-up This contains: 12V Barrel Jack DC Motor Controller Peristatic pump On/off Switch The switch is optional since the motor…
The AWQP team is working on a development and testing of a low-cost water quality sampling system. This system is intended to significantly reduce the cost of water quality research equipment. These devices will help reduce the cost…
I've written up some details on the build here In playing around with peristaltic pump designs quite a bit lately, I was curious how well the same basic idea would work as a valve...not too bad, in my opinion :) Currently used as a…
similar but not exactly this one: https://amzn.eu/d/5Glt5OA (can't find the original one online right now) small, and mechanically stressed part, therefore decided to go with SLA-printing only.
To use together with a geared Nema17 stepper motor with a flanged 8mm output shaft like this one http://2.wlimg.com/product\_images/bc-full/dir\_37/1091420/geared-stepper-motor-1392929.jpg I am using 10mm OD surgical tubing. Action video…
This adapter cover allows you to use a ball bearing instead of the unserviceable bushing that wears and has no replacement (must purchase entire pump, not just cover) It is designed to hold this bearing:…
Adapter for a AC peristaltic Pump to use it with a stepper motor
Needed a plate mount for a 12V peristaltic pump. In this case 48mm bore mount distance.
This peristaltic pump has been made as small as possible to inject small quatities of test solution on command. It has been tested with this tubing.…
This is a stand for a generic 12v peristaltic pump (available from many vendors). The particular peristaltic pump used and fitted to this case is this one . Bill of Materials/Required Hardware: 2x M2.5x16 Socket Cap Screw (source:…
