Counting matching models…
Hi there, Here is an airsoft suppressor (150 x 40 mm) with an M14x1 LH (left-hand) thread. It fits any airsoft gun. It features the standard M14x1 left-hand thread found on all types of airsoft barrels. It fits perfectly and holds…
Surefire SOCOM 2 Series (14x1 CCW) made in Fusion 360 This is not an “exact” replica of the Surefire SOCOM Series, I found a few on thingiverse but they don't print very nice, and need support. So I decided to make one myself (for airsoft…
This is a stackable Airsoft Suppressor Baffle that I made for Surefire LLC replica suppressor. Print as many as you need and just stack them. Each one is 16.6mm high, and they have 1.6mm overlap, so a stack will be N*15mm+1.6mm high,…
The Principle Suppressors reduce the sound of the explosion by trapping and slowing down excess gases. With airsoft silencers, the most important thing is to reduce the high frequencies, because they are the main culprit for revealing the…
This silencer is based on the Osprey 45k and was designed to be used on my 1911 R32 and holstered on my Swiss Arms Adapt-X, so the dimensions are definetly not accurate in relation to the RS one. Dimensions: 23 x 35.5 x 150mm The baffle…
This socom silencer should be compatible with my gb-22.
Important notice: First thing is first:) This design is free for the benefit of the community, but If you like my designs and want to contribute, you can make a donation to buymeacoffee or paypal, that will be greatly appreciated. I know…
I couldn't find a suitable free tracer housing for my Airsoft guns so I designed my own. It fits an xcortech tracer down the end, so you can have extra barrel length inside the suppressor if needed. I added some electrical tape around the…
Do you like tiny suppressor like me? I present to you my little custom suppressor for the AAP-01! You can put this bad-boy on your airsoft replica with the 14mm CCW thread to have a really cool looking gun! !!!!!!! AIRSOFT ONLY !!!!!!!…
Your printer needs to be able to print fine threads. I used some silicone grease to make them easier to fit/screw on. NO SUPPORT NEEDED :) The threads are m30.5x1 You can "infinitely" stack this suppressor
I remixed n.leinad great design to make it a bit more of a workhorse. I enjoyed the original design, but from previous experience with suppressors with lots of baffles, adding more baffles after 4, the noise attenuation is unnoticable…
There's two versions, "OTB" (Over The Barrel) has the thread around the middle of the silencer and the normal version has the thread at the base. Silencer dimensions: 157mm x 35mm OTB: The barrel hole is 15mm and the thread starts 70mm in…
This is a very old design. Please look at my other moderators for a current design This moderator is for air gun use only! Do not attempt to mount it to any other type of gun! Follow you local laws regarding moderators! This moderator has…
Hi, thanks for downloading my file! I made this suppressor/silencer for my Novritsch SSG24, because the one Novritsch sold on his website was a bit too expensive for my taste. How it's made This silencer is made up of three easy-to-print…
I print this with some brim, because it's rather tall for how little area it has to adhere to the print bed. Needs no support. I printed it in PLA but I assume any filament will also work fine. Should fit any airgun with a ½"-20 UNF…
Easy to print feet to help stop the printer transferring resonance vibration to the work table. If your new printer turned your table into a drum, you want these. Cheaper, easier, lighter, and better looking than a slab of cement. No need…
SP-01 Shadow 119x22mm, 1/2x28, cal. 6.0mm SP-01 Shadow 119x22mm, M12x1, cal. 4.5mm
Insert this baffle into a Donny FL suppressor to make it quieter. I've experimented with several different types of baffles and this is the best one I've found. Mine is for a PCP .22, - but this baffle could certainly be modified or…
An adapter to mount common 14mmCCW parts to an airsoft MP9. Tested to fit on KWA.
Hey, this is my first Thing. I design this holder for a hunting friend of mine. Feel free to used it. High: 150 mm deep: plate 6 mm, holder: 76 mm width: 70 mm hole: 55 mm diameter I used supports only for the top of the hole. Print…
Why My Well MB01 came with a 26mm CW threaded outer barrel, and while adapters to the more common 14mm CCW airsoft flash hiders do exist, they usually cost around 10-15 bucks+ shipping. Features Pre-modeled threads. The thread pitch on…
This piece is currently a work in progress as I have not finished printing it or tested it yet. NOTICE: This suppressor is intended only for use on BB guns / Air Rifles. This in no way is meant for production for or use on actual…
This is meant as silencer/suppressor replacement for SPA PP750 cal. 5.5 mm internal suppressor. I accidentally lost the originals, so I did this one. I've also put cotton wool outside the K-baffles, works better than original imho. Each…
A 3D printable mock suppressor for airsoft guns. The thread is inset inside the suppressor by 50mm. The suppressor is suitable for RIFs with a threading of 14mm CCW. The front end of the suppressor unscrews to allow access to the inside…
Air rifle moderator, for use with sound dampening felt or foam . 193mm overall length, the tube is 185mm long, 40mm outer diameter, 36mm inner diameter, each cap extends 4mm out of the tube. Inspired by the many aftermarket designs that…
This is a generic flange plate. It may be used with other systems to extract fumes or to bring in cooler air for PLA/TPU, etc. One side effect of having this installed is that it does quiet the especially loud aux fan to an extent. It's…
Hey all, Made this Suppressor while I had some down time and had nothing to do. Fits a 14MM Counter Clockwise thread that is common on most Airsoft rifles. Made this for my G&G combat machine. Adds about 155mm of extra outer barrel length…
This is a very old design. Please look at my other moderators for a current design This moderator is for air gun use only! Do not attempt to mount it to any other type of gun! Follow you local laws regarding moderators! This moderator has…
I recently bought a Wolverine MTW and wanted to have an integrated/nested suppressor in the handguard, but the more I looked the more I had difficulty finding one that would fit AND that I liked. The internal diameter of the MTW's…
print with brim for better adhesion
print thread side up 100% infill 0.2 mm layer height
print it, drink your Energy, make a hole in the top, size as large as the opening for adapter (14mm) glue it together. ready to shot.
Airsoft only. Not for firearms. Barrel extension / mock suppressor for King Arms PDW 9mm SBR M-Lok airsoft rifle for extending the barrel for a 363 mm ( https://www.amazon.com/gp/product/B078SC421D/ ). First version broke at the thread…
Disclaimer : This design is intended for use with Airsoft Guns ONLY and NOT for real firearms. Safety Note : Always wear appropriate protective gear, including eye protection, when using airsoft weapons to prevent injuries. Use Caution :…
This is only guaranteed to work with 16oz white monster energy cans due to some flavors being different sizes. You're welcome to try others but don't say I didn't warn you. Make one cut around the can (I've found that the best/easiest…
After printing out another sight pusher I decided I wanted to make a version that was smaller and quicker to print with a captured pusher. I also wanted to use more common hardware and I wanted it to accommodate supressor height sights up…
The original file for this suppressor had issues where the inner diameter was too small for a 6mm BB to pass through. This file has a larger inner diameter as well as a larger overall body with support for 14mm CCW threads. This…
The original creator for this created a wonderful design for a tracer housing or just a great mock suppressor. However, only long and short versions were available. This is a medium sized version of those in which is about an inch shorter…
Update 20240229: Added step file in case any one wants to do a bit of DIY. -------- I've been looking for a mock suppressor that: 1. Looks long but doesn't add too much to the overall length of the gun. 2. Slim but also fits a tracer…
Credit to https://www.printables.com/@nleinad and https://www.printables.com/@QuentinL_4378541 for the originals. Here I have added some sectional threaded baffles. The idea was to have a separate printable section so you could add as…
Miniatures of all detectives and monsters from the add-ons suppressed memories and recurring nightmares miniatures. Mansions of Madness Second Edition — Recurring Nightmares: 8 detectives: Michael McGlen, Sister Mary, Gloria Goldberg,…
I beefed up the frame by using 5 perimeter walls and adding a second spot to hold the slide on both sides. The pusher was redesigned to fit suppressor height sights. I added a hole in the wrench so it stays captured to the tool and a…
Designed to fit in the Avengers QD Mock suppressor that is modeled after a Knights Armament suppressor. I had some problems with the “.20 SPEED” preset, but “.20 STRUCTURAL” worked fine. Mock Suppressor:…
This is a very simple MOCK airsoft suppressor i designed for very specific reasons. i have a cyma standard ak 105 carbine. CYMA Standard Stamped Metal AK-105 Airsoft AEG Rifle with Synthetic Folding Stock (Package: Gun Only), Airsoft…
A remix of Crosman 1377 suppressor V2. The original was a 5mm hole for 4.5mm (.177) pellet. This has a 7mm hole for 5.6mm (.22) pellet. I also made this a two piece threaded design. This makes managing supports simpler. Also, if you break…
Bei 15cm Druckhöhe hat der Halter einen Innendurchmesser von 6cm. Die Aussparungen für die Magnete sind in der aktuellen Version für 20mm Durchmesser und ca. 5mm dicke Magnete gemacht. In der Mitte hatten meine Magnete ein Loch, das ich…
A replica of the muzzle device on Han Solo's DL-44 Blaster. It is set up to work with 1/2" x 28 threads. it will thread onto AWCY's Proto Barrel ends (available elsewhere). Either the "One Part Option - Permanent" or the “Two Part Option…
Silencer adaptor for use with Weihrauch HW40/Beeman P17. Fits 1/2-20 UNF threaded moderators. Held in by friction. The options to use a suppressor with the HW40 were limited. This works pretty well. Only issue is that when attached, a…
The suppressor goes over the muzzle brake . Thread on bottom of the muzzle brake is 14x1L , compatible with most AK style replicas , muzzle break - suppressor body joint is a M22 standard thread with 1.75mm clearance , suppressor-end cap…
Replica Glock-18 found here → Click Me The suppressor isn't modeled after any specific IRL suppressors. It's meant to be simple. Installation: Slide the suppressor into the barrel. The side with the rifling will go into the barrel and use…
NOTE: The revised version fixes a few minor errors and adds additional vertical support. These were designed to allow you to mount multiple suppressors of varying calibers to different surfaces including walls, safe doors, etc… These…
a remix of the extended nerf barrel with a suppresser.
Tlumič výstřelu s vnitřním závitem M12x1
I designed this suppressor in a way that you dont need an special threads to affix it to your airsoft gun. You put the small cap over your barrel's threads, add the Brighter C and tighten, and then add the suppressor over top. There is…
all kinds of different combos, outer shells, internals, end caps with and without holes for gas/sound to escape all of them fit together except for the long version, the longer version will still work with the endcaps but also need a…
This is an airsoft barrel extension styled for the Classic Army X9 Nemesis ARP. I haven't formed the threads for screwing onto the outer barrel; instead it is sized for the treads to cut in themselves. This will give up to 100mm extra…
Short, stubby and hexy suppressor. Bit of a play around in Fusion, someone might want it :) 14mm ccw thread. Print without supports at whatever settings you fancy, rafts not required.
[EN] Airsoft MK18 Mock Suppressor / Silencer (14mm CCW) Custom tactical mock suppressor designed to fit the MK18 airsoft replica. Features a standard 14mm Counter-Clockwise (CCW) thread, making it fully compatible with most M4/AR15…
Functional suppressor that reduces noisy shooting noise, for the double eagle M904G that fits inside the handguard. It is compatible with other rifle models with 26mm thread.
MOCK SUPPRESSOR FLUTTED 14mm CCW THREAD (most common) 150mm lg 38mm diam. 9mm id for optimal extended barrel support
This is a 27mm diameter Monocore for a Monocore Suppressor for your .177 caliber airguns. THIS FILE ONLY INCLUDES THE MONOCORE. Since there are so many different-diameter barrel airguns, there is no way I could design an individual…
Sticks to a prop gun with the correct fitting
you can stuff it with a sponge like I did to make it work, for 13mm barrel
14mm ccw treads and a suppressor with removable front cap for well r1 uzi Category: Toy & Game Accessories
Couvre Silencieux Suppressor Cover Diamètre Intérieur +0.15 Diamètre Extérieur sur toutes les versions = 57.1mm
Print the parts with thick walls and top/bottom layers (2.4 mm.) Use 40% infill. It needs to be strong. In addition you will need: 2x 688ZZ (or 688-2RS) ball bearings (8x16x5 mm) 4x M4x10 Allen Head screws with washers 4x M4 T-nuts 4x…
Suppressor with a honeycomb pattern. The STL file includes an M14x1mm thread, 13 mm in length. The thread pitch can be modified using the provided Fusion 360 file.
40% infill or More PLA + or PETG
SSP18 mock suppressor Shoutout to “H6K2LH” for the idea. I need to mention that this is not a repost, I did make these on my own, so please, don't call me a copier. I made this model because I wanted a super cool looking mock suppressor…
NOTE: 09/21/2025 G3 and G4 holsters for suppressor height front sights up to 10mm added. This is a pair of open bottoms TPU holsters for the Gen 3 and Gen 4 Glock 19. It will fit pistols both with and without a TLR6 tactical light. It…
Here is something that came from my years of trying to make the quietest springer blasters. It is a 16mm (Caliburn) direct mount suppressor with integrated rifling for short darts. It works best with a TPU piston and TPU extended spring…
This is a custom designed suppressor mount that I saw in the gunsmithing subreddit. Designed by u/VernoniaMW. To create this model, I used a sketch and a set of coordinates that u/VernoniaMW included in his post. I've never modeled…
An airsoft muzzle device that covers up and protects either a barrel extension or a tracer unit. Does not reduce sound in any way, cannot be threaded onto real firearms, and is entirely dog friendly. Does not filter oil. Will, however,…
I printed the 52mm file from the original creator and found it was not what I needed. I resized the model to fit several Dead Air Suppressors. I then merged each holder to combine them into two sets of 3. These holders fit the following:…
I love the original gun made by DeSteiner ( https://www.printables.com/model/1446099-desteiner-colt-m1911-mechanically-working-prop-gun ) but I always thought it need a sick ass suppressor. My design was inspired by games like Battlefield…
Just a dinky little side project that I thought would be neat. I designed this for my own personal scattergun, which is the TS version. This thing should fit fine on most of the scattergun variants, though I'm not entirely sure if it will…
This mock suppressor is compatible with the SMG body kit by XFoxGames. You can purchase that kit separately here . The micro stock should be compatible with hollow buffer tubes. The one I have pictured is a folding stock from Evike, but…
The suppressor is 7" long and 1.3" (34MM) in diameter. I printed with %25 infill (Grid). No supports needed! Enjoy and leave a comment if you print it!!!! *Sorry i don't have the best pics for this model * This is free for you to print,…
This is a model of a suppressor that should fit with the handguard, if you have any suggestions please comment
This is a shorter version of the original. I've found that on my AEP, the suppressing performance is essentially the same, and the sorter suppressor is more maneuverable. The plug on the front is also shorter, to maximize the available…
02-06-2025 UNW-T6 outer barrel options added --- as part of the big V24 update. the 14mmccw barrels have been made a bit stronger and partisan 6 barrels have been added - 14mm CWW barrel tips have been added --- these are the 2023…
A set of Customizable Mock Suppressors for your KWA M11A1. I also threw a smaller “one piece suppressor” in. Combine them however you want. They fit a typical AceTech Tracer Unit. Supports are a little more difficult for this model. MS -…
Valorant suppressor adapted to airsoft, consider print the test fit before printing the entire model . anti clockwise thread ''VALORANT SUPPRESSOR'' was created under Riot Games' "Legal Jibber Jabber" policy using assets owned by Riot…
02-06-2025 UNW-T6 outer barrel options added --- as part of the big V24 update. the 14mmccw barrels have been made a bit stronger - 14mm CWW barrel tips have been added --- this is a 300mm long barrel replica made for the LB (the…
32 mm outer diameter carbon tube needed Use a threading tool to add the right thread for your airsoft gun also included the sldprt files for solidworks.
battery suppressor outer barrel with room for acetech brighter c tracer unit
If you're like me, paranoid about your printer randomly catching fire and upgraded your CORE One from an enclosed MK4S, this might be for you. Since Prusa themselves haven't released anything so far I decided to make a quick bracket to…
This model uses four M2x5mm countersunk machine screws, commonly known as flywheel cage/motor screws in the hobby. I designed this because I wanted a muzzle piece for my Diana that had a fairly visible footprint, without adding much bulk…
Hi, still a 3D modelling noob but learning, I have here my take on the 2003 Clone Wars suppressed clone pistol. I have done my best to replicate the form of the animated blaster but with extra detailing for a more realistic style to use…
The rear slides over the hop up adjuster and is open at the bottom so it doesn't interfere with MLOK forward grips. The rear part is held in by the front piece once its screwed onto the barrel thread. You will have to remove the barrel…
This is a low profile clamp wrench for Rugged Suppressors center fire rifle locking collars. This will work with Surge, Razor 556 and 762, Micro, and Radiant models and their new RUM HUB adapter. This is a remix starting with a trace of…
MOCK SUPPRESSOR TRINITY 14mm CCW THREAD (most common) 150mm lg 38mm diam. Built in two part with an I.D. of 32mm. This supressor is designed to be use with internal foam to supress the sound of gas airsoft bb gun.
an over barrel suppressor that screws onto your long barrel US version (not sure if it fits short barrels versions) of the Novritsch SSG96 orange tip.
16 CW suppressor with foam insert compatible. Works with SSX23 or Mk23! A Few Things to Note: - Used Electrical Tape to hold pieces while glue set. - Compatinble with the Novritsch Ghillie Suppressor Cover - Uses 4" foam paint rollers as…
