Counting matching models…
"Mole and snowman" (Krtek a sněhulák) cookie cutter. Cookie cutter is made of 2 parts - cutter and inner stamp. Parameters: Snowman Stamp - 38mm x 63mm x 4mm Cutter - 47mm x 72mm x 12mm Mole Stamp - 64mm x 78mm x 4mm Cutter - 73mm x 87mm…
The ToupTek AFW filter wheel has screw holes either side to attach tilt plate and OAG via screws. If your using the M54 adaptors to attach to telescope and camera (rather than the screws), then the screw holes are not covered and could…
requires 4 4mm heat set inserts to mount the 120mm fan and 4 15mm m3 standoffs between the block and the printed part. Longer standoffs would be fine, but 15mm is the minimum. attach the printed part to the standoff with 10mm m3 bolts and…
Při brouzdání internetem jsem narazil na toto video: (a moc se mi líbilo). Teorie je např. tu: http://edu.techmania.cz/cs/encyklopedie/fyzika/magnetismus/magneticke-latky Pro demonstraci ve třídě budete potřebovat: feromagnetickou látku…
Tisk velmi jednoduchý - bez podpěr a ideálně z PET-g. Po vytištění opatrně nakloněním vložte do šachty detektoru. POZOR - jedná se o box do starší varianty loketní opěrky Nokta SImplex. V nabídce mám i na nový typ.
I printed it with 0.16 mm Layer height. No supports needed. You may need to add a brim to prevent the pieces from falling over.
Pastamatic Filament Spool Winder Add-On by Kistek. This add-on is for Pastamatic filament spool winders and is meant to secure the drive spindle so that it does not come out of the cradle during operation. This is especially important for…
This Furitek Slidetech ESC has a cutout on the bottom for airflow and cooling…which is really helpful….except for when looking to double-sided tape mount it to the car. I created this simple mount that allows the ESC to sit off the bottom…
This design adjusts the angle of the throttle quadrant 30 degrees to a more comfortable flatter angle. I designed it to match the angle of the throttles seen on airliners and other aircraft. For easier storage it is printed in multiple…
This is a film holder for 127 film for use in the Plustek OpticFilm 120 series of film scanners. It is pre-split so it can be printed on a reasonable size printer. The two halves snap together and should be glued or taped together. I…
🛠 The Little Mole (Krtek) – 7 cm Height This finely detailed 3D printed model of the beloved character Krtek (The Little Mole) is perfect as a decoration, gift, or collectible. The model is printed with the following specifications: Layer…
The Minisforum ITX boards support an unusual hole placing for the cooler mounts, 52mm on the edges. The model by NAnglo uses a slighty wider spacing, therefore I needed to adapt it a little bit. Print with temperature resistant and robust…
A box for the high voltage probe. The key feature is the cutaway at the bottom. These probes have cables coming out of both ends, which makes it not a good fit for a standard box. Updated design which has holsters for probes, oscilloscope…
Print this in TPU with supports under, in the orientation in the file. You can adjust the number of perimeters and infill amount to adjust stiffness, but I used the slicer defaults.
If you enjoy my creations/remix, feel free to support me via buy me a coffee- https://buymeacoffee.com/spydergiant 12/26/25- Added Barrel spacer. Finally got my fx-3 spring. Using Nutty's hijinx catch 3 (Because I went with no ptfe as I…
Razítka na těsto jsou kompatibilní s tímto modelem: thingiverse.com/thing:1802161 . Cookie stamps, compatible with : thingiverse.com/thing:1802161 Enjoy!
Purpose This mount allows the Mateksys M10Q-5883 GPS & Compass module to be fastened to the Speedybee Master 5 v2 RC drone. Instead of mounting the module to the drone's rear, the mount moves it to the front. The main purpose is to get…
Purpose This mount allows the Mateksys M10Q-5883 GPS & Compass module to be fastened to the Speedybee Master 5 v2 RC drone. It mounts the module to the drone's rear. Special care was taken to design the mount such that the module sits…
A Housing for the ProTek RC Balance Socket board. Uses previously used hardware (2 screws). Easy assembly, push on top. No additional hardware required, no supports.
A remix of the model made by @Mike81622, added a few ergonomic features, and change to attach it to the the Tek-Lok style belt clips.
I use this for mounting my CTEK MUS 4.3 Charger bracket to Slatwall along with M5 bolts. (it just threads straight into the part I spent a lot of time trying to tweak the dimensions so that the parts would latch onto the Slatwall but not…
This print is a friction slide mount for the Mateksys M8Q-5883 . It can be hot glued to any desired surface. The design is parametric and can easily be modified.
Under desk mount for a "teetek USB 3.0 DP KVM Switch 2 in 2 out", which is a Dual Display Display Port KVM from treetek.
SpyderTek Lynx shroud, but with PKI RR muzzle mount. Uses m3 heatset like this: https://www.amazon.com/dp/B07D683Q26?ref=ppx_pop_mob_ap_share&th=1 , or you could get away with Voron inserts, and use m3 x 10mm screws through the muzzle.…
It is not possible to buy spare bowl. So I have decided to create this model. Print it with supports everywhere.
Pasuje dobře zatím ani při vyšších rychlostech nevypadl. :) / It fits well and so far it hasn’t fallen out, even at higher speeds.
This replaces one of the 3.5" drives on the Fujitsu FM77AV with a gotek. It's designed to fit one of the larger (small) oled screens, but the Fusion file is included if you want to modify it. I recommend printing at a relatively high…
Simple model that will very snugly hold a Greathtek KVM switch for two PCs. Note that this exact device is sold under several different brand names, too, such as TeeTek or PWay. It will be held in the front by a very unobtrusive 0.4 x 1,3…
Panels you can glue onto your wavetek meter front panel around the binding posts to reinforce the plastic if it's already cracked. You can glue the original label decal back on after.
Created a holder for my Tekton 1/4 torque wrench for the Gridfinity family
Printed in TPU 95 with 4 walls top and bottom 80% gyroid infill support on build plate only
Cover for board from ebay , to lower the shock hazard. I'd suggest non-flammable filament like fulfilling the UL-94 V0.
I printed mine with TPU with four wall sides top and bottom at 80% gyroid infill. Stiffens up the entire nerf bar and will last forever.
Printed in ABS at 4 walls top and bottom, 40% cubic infill. Fits TIGHT on side guard, will need to short 2.4mm screws for install. Then use double back tape to secure your switch in place. WAY easier for a marshal to locate mid heat!
THIS IS A CLEAN VERSION WITH NO WRITTING ON FLAPS. Printed in TPU 95 with 4 walls top and bottom 80% gyroid infill support on build plate only
Print in TPU, will last forever. Remove if the track loamy/wet as the produce drag
Print in TPU, will last forever. Remove if the track loamy/wet as the produce drag
Si comme moi vous avez perdu les joins de support de vitre latéral de votre boitier Ximatek Zeus
I made a little bracket to properly mount a dual SFP NIC inside my Lenovo Thinkcentre M720Q. Small slots for the LEDs are included. The model has holes for M3-inserts. It is printed with the outside facing side downwards.
Martin Gray (Mieczysław (Mietek) Grajewski) – Buste 🇫🇷 Description (Français) Ce buste en impression 3D représente Martin Gray , né Mieczysław (Mietek) Grajewski , figure majeure du témoignage mémoriel du XXᵉ siècle. Il est directement…
Use a bit of doublesided tape to fixate the module in the cover. Not much else to say. OpenSCAD file included as always. Have fun!
The Onshape files can be found here: https://cad.onshape.com/documents/df0b3f0a4026fec2714bccaa/w/c6e1445203c64036d594bf2b/e/e127d6d1c369c972726e20af?renderMode=0&uiState=6988c5b4e200f073ca41870f Feel free to use or modify as you see fit.…
I only remixed it. I did not printed it by myself.
EN: I created button of center console for Skoda Fabia 1 . I wanted to created original phone holder, so I use parts from non-functional old phone holder, did some changes in my button model, print it, and so far it works! Left , middle…
Can't find any matching stand for this heavy case (net weight 13kg), so decided to make one. Printed using Prusa Core One + and PETG (you may try with PLA if you want to), with 0.2mm structural profile and these custom settings: Fill…
Simple holder I made for Ctek Zafir 100. I printed it in PETG with 3 walls and 12% gyroid infill. No support needed, print with bottom down.
I recreated inserts for the drill table of my Teknatool Nova Viking DVR drill press. The original insert had some marks from drilling, so I made two versions: one closed like the original, but a few tenths of a millimeter higher to reduce…
A simple and flush mount for a standard 5 inch Raspberry Pi Screen, fits to the back fan mount with no modifications to the case! Parts needed: Raspberry Pi Screen: https://amzn.eu/d/0il68j7 -…
The original pinholder has a tendency to break with age. A simple fix for an expensive piece of gear.
Number 7 in the series. Once again it's compatible with parts of my other sabers. I opted to go without the switch module since it is already pretty long and has an auxiliary button anyways. So there is a Switchdelete module or you can go…
Didn't find what would interest you? Let's create your dream project together. Write to this email : ----> [email protected] <----
Put this on the head of your C2 flashligh. Works with C2, C2 Pro (Nichia, WR etc). Won't work with C2 Pro Max. Add fuzzy skin to the bulge in the slicer to get better diffusion. Transparent PETG is an optimal choice for the filament.…
End stops for powertek t-track. Based on the design from https://www.thingiverse.com/thing:3875606 which is for the Kreg T-track. That will also work on PowerTek T-track but is ever so slightly off so this design is just a bit of a better…
Here is my mount for the Lian Li 8.8" Secondary Screen. It is designed to fit the Asetek Front Mount, it is press fit, and the monitor being an all metal design means that the weight of it keeps it in place I have shown the longer version…
Better fitting clamps for the T9 tablet from Tripltek for the motorcycle mount. The original clamps didn't include enough space for the rubber on the outside of the case. I've included a cable clamp for the usb cable. You'll need some…
Podšálek ve tvaru čtyřlístku. A coaster in the shape of a four-leaf clover.
Set of M5, M6, M8, M10, M12 NUT CAPS WITH WINGS FOR EASY TIGHTENING Sada KRYTEK NA MATICE M5, M6, M8, M10, M12 S KŘIDELKY PRO SNADNÉ DOTAŽENÍ
Bonjour créateur, Je vous présente ce modèle que j’ai dessiné, Les instructions d’assemblage sont disponibles en téléchargement Pour l’impression, je fournis un fichier 3mf, sinon un gros remplissage n’est pas nécessaire et il n’y a pas…
A magnetic stand for your Alientek multimeter. Pretty sure it requires the "luxury" version of the multimeter with magnets in the back. Has 2 slots for 15mm magnets to glue in. Works pretty well for me so far. f3d file attached so you can…
An air intake system for the JessEm Pow-R-Tek router. A full setup requires 2 elbows, 1 intersection, 2 hose to pipe adapters, and a flange, The 2 elbows slide into the intersection on opposite ports, and this then friction fits onto the…
Funko Pop Modell von Kogoro Mori aus der Anime Sendung Detektiv Conan. 10cm Hoch auf einem Sockel.
Funko Pop Modell von Prof. Agassa aus der Anime Sendung Detektiv Conan. 10cm Hoch auf einem Sockel.
Eine Figur von Heiji Hattori aus der Serie Detektiv Conan. 10cm auf Sockel.
Eine Figur von Kaito Kid aus der Serie Detektiv Conan. 10cm auf Sockel
Eine Figur von Kommissar Megure aus der Serie Detektiv Conan. 10 cm auf Sockel.
Eine Figur von Ran Mouri aus der Serie Detektiv Conan. 10 cm auf Sockel.
Eine Figur von Wataru Takagi aus der Serie Detektiv Conan. 10 cm auf Sockel.
Made a shelf for the industrial board of AXIOMTEK
Armytek wizard etc lamp holder on helmet. Support no need. PETG full walls
deutsch: Ich verwende den hydraulic Tektro brake bleed cup von Alex zur Entlüftung des Bremshebels. Damit kein Öl austritt wenn ich diesen Trichter aus dem Bremshebel raus drehe habe ich diesen Stopfen entworfen. Ich drücke ihn von oben…
PL: Niniejsze repozytorium zawiera zbiór 40 modeli testowych zoptymalizowanych pod kątem różnych rodzajów termoplastów. Struktura została podzielona na 9 grup tematycznych: od podstawowych polimerów (PLA/PETG), przez materiały…
Alientek T90 Case Insert (C245 tips) Custom insert for the Alientek T90 soldering iron case. Keeps your tools organized and everything in one place inside the original case. What fits: 2 tweezers (up to 136 mm and up to 130 mm) Heat…
This design fits perfectly into the rihgt-hand hatch of the 1/6 scale Armortek Tank. This allows for the following to be located in the same place: The main switch The switch for the smoke generator module The battery voltage indicator…
This design is a specific need I had to equip the 1/6th scale M26 Pershing tank produced by the company Armortek in the UK. Originally, the hatches on the M26 Pershing tank provided access to the interior, and I thought it would be useful…
This design is a specific need I had to equip the 1/6th scale M26 Pershing tank produced by the company Armortek in the UK. This plate allows the tank commander's bust to be fixed in place. It is fixed from the interior of the turret with…
Moai Tlaltekayotl 🇫🇷 Description Ce modèle revisite la silhouette emblématique des Moai à travers une interprétation inspirée de la puissance des souverains aztèques. Avec ses proportions massives et son expression stoïque, il dégage une…
f you like/print this insert/content, please follow me and “like” my insert :) This is an all-in Deluxe insert for Tekhenu. Key features: Box to tabl e => all resources, and etc, are able to be set right on table for use (no resources…
DollaTek 25a MOSFET DIN Rail Mount (LOW PROFILE!!) Much in the same way as my Micro4 board, I needed a compact, low profile, mount for my MOSFET (yes, this Voron uses a 24v bed, yes it heats up quickly, yes it has a good bed mesh). Due to…
I made a little holder for my vape and it fits onto my bag, I use this mainly when walking to keep my pockets free. I have added a different version with a belt or loop hook
Hi all! Here is my remix of another design posted here on Thingiverse. Made the mount compatible with the DJI O4 Pro, which bolts on the rear, and a 5V fan bolted on the front. The C20T gimbal sets as previously designed, with an airspeed…
Spacer to place Saitek Combat Rudder Pedals away from wall. Sets the pedals around 220 mm away from the wall. Very sturdy - except pins, but they are not really mechanically stressed. Complete with anti slip or felt pads on bottom and…
This Spacer (Remix) is for the rudderpedals from Saitek/Logitech to bridge gap between ur pedals and the wall. The Original Model from PDrill used printable plastic pieces for it, which took, if u had a long gap to bridge quite a lot of…
Probably the best knobs for tektronix oscilloscopes. In this case, mine is the tds 210, but there are many compatible ones. There are already many models, but I didn't like any of them. They all had a big defect, they don't fit together.…
Cover and holder for three USB ports on a Phanteks Evolv Shift 2 computer case. Adds one extra USB-C port to the existing two USB-A ports. Requires a mainboard with a USB Type E connector and a suitable front panel adapter cable like this…
Krabička je ze tří dílů a vyžaduje 6ks zápustných šroubů o velikosti 3x25mm. Jedná se o jednoduchý a pevný design. Do základního dílu vložíte PCB testeru a vyvedete připojení baterie průchodem do jejího prostoru, poté zaklopíte zadním…
