Liczymy pasujące modele…
Philips OneBlade holder with drain hole. Print Settings Printer: Geetech E3D V6 Rafts: No Supports: Yes Infill: 15% Filament: Generic PETG, PLA-F, PLA White Notes: 4 walls for strength. Category: Bathroom
M12 M16 M20 Nut Print Settings Printer: E3D V6 Rafts: No Supports: Yes Resolution: 0.2 or less Infill: no Filament: generic any Notes: print in smallest resolution your printer can print for better threads Category: DIY
Aquarium Under Gravel Filter I designed this to be easier to print than existing under gravel filters. It is 140 x 140 x 10 mm and can be scaled in cura to fit other size tanks. Base pieces can be cable ties together. Uplift tube is hole…
Xaiomi 9T K20 Pro Phone Case 4 versions 1.4 mm thick back 1.0 mm thick back Split for PETG No Split for TPU Print Settings Printer: Geeetech E3D V6 Rafts: No Supports: No Resolution: 0.2 Infill: No Filament: Generic PETG / TPU Any Notes:…
Remixed to remove need for supports. Print Settings Printer: Geeetech A10M Rafts: No Supports: No Resolution: 0.2 Filament: GENERIC PETG / PLA Notes: Print Vertically Category: Replacement Parts
E3D V6 Mount A10 A10M A20 A20M Designed to mount on the existing A10 X carriage, use two M5x30mm SS Hex head screws for more support / key instead of original dome head screws for top roller bearings, for quick removal and replacement…
TTGO VGA32 V1.4 Case with access to all ports and switches uses 4 x M3 screws Remix of https://www.thingiverse.com/thing:4565213 Print Settings Printer: Geeetech 3in1 E3D V6 Rafts: No Supports: No Resolution: 0.2 Infill: No Filament:…
Remix of Booty's K1 Max Linear Rail Gantry Carriage with Probe and without. Use Standard M3 threaded inserts instead of M3 Voron threaded inserts. Also add cable tie mounts for extruder motor / filament sensor wires. Added version to use…
Upgraded my Geeetech A10M Y carriage to an New Ender3 type to reduce mass. Due to the roller mounts being further apart i had to create a new mount for Y axis end stop limit switch. (see y carriage photo RED and YELLOW circles show the…
Remix of Booty's XY joints with probe for K1 and K1 Max Added chamfer to top inside edge to allow cable chain to ride over XY Joints Added A and B text to identify A and B belt. Category: 3D Printer Parts
USB Plug to fill the hole when usb socket is removed. Category: 3D Printer Parts
MacBook Air foot feet for Model A1465, should fit other model using 18mm diameter feet. Need to replace one of my broken feet. Print Settings Printer: E3D V6 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Generic PETG or TPU…
Add on Accessory for Makita Tool Battery (18V to 21V) with 4 switched outputs. 4 USB QC3, Apple, Samsung etc Fast Charger. 6W LED low power Emergency Light. (truck/trailer side light 12 to 24V) 48W LED high power Spot Light. (auto spot…
Rigid Bed Mounts for K1 or K1 Max when PRTtouch sensors are removed and Cartgrapher 3D or other eddy sensor or touch sensor on tool head is used. Option for silicon spacers or Magnets with 10mm Kossel Steel Balls M4. Magnetic Mounts…
I added a lot various holes sizes from 1mm to 6mm and 10mm deep , XT60 and 2mm 2.54mm and 3mm DIL pin spacing. Also added some curve tray below where you solder wire to catch solder drops or hold parts. Category: Electronics
Wheelchair Controller Handle 6mm Mount Joystick Printed with TPU
Y-Axis belt tensioner for Geeetech A10 or A10M or other 3d Printer using 2040 V-slot. Due to replacing my Y-Axis carriage with New Ender type that used wider spaced rollers, rollers were hitting my Y-axis tension original mount. This…
Breville Sage Bambino Cup Holder for bottomless portafilter Raises Cup to be closer to bottomless portafilter to avoid mess if it sprays. Also print guard and mirror it for other side to lock it in place on drip tray Also have cup holder…
After trying other A10M Parts Fan ducts, and they blow on nozzle i remixed to place it lower and add lip to force some air downwards. Also fillet mounting hole corner. Print Settings Printer: Geeetech A10M Rafts: No Resolution: 0.2mm…
After trying other A10/M Parts Fan ducts, they blow directly on nozzle. I copied the original A10M Fan duct and made it longer so it blow below the nozzle, also trimmed it and laid it flat by using 45 degree cuts. Print flat no supports…
remix to add M3x3x4.5 threaded inserts to hold cartographer. print at 45 angle no supports needed Cartographer 3D offset is Y axis -22mm. V2 has 2 front mounts. add 2nd fan mount to strain relief. 2 versions, inner or outer of fan…
Replacement joystick handle for electric wheelchair Print Settings Printer: e36 v6 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Generic TPU black, light colors easily stain. Notes: my print settings print half the speed…
USB, TF, micro SD, SDcard Holder using Vase mode (Spiralized outer contour in Cura). Holes for mounting are 3mm. it also holds USB C if inserted diagonal in the square holes. I have added V2 with tighter fit for SDcards I reduced width to…
Stepper Motor Plug for K1 Max Tripple Z to cover hole for stepper motor wiring. Category: 3D Printer Parts
Case for ZX-UNO 2M VGA Retro 8bit Computer. Can print multi color or single color. use 4 x M3 Hex Screws 10mm or longer I have used a 3.5mm DC jack instead of 5.5mm DC jack (3.5mm is safer for 5V, as all my 5.5mm are 12V or 24V DC) I have…
I have removed K1 Max Cable Chain and replaced it with 500mm x 7.4 (8mm) Cable Tie. I did not want to use a riser and keep the cable horizontal. Cable Mount 5 Deg has upwards angle to help offset cable sag. Need to cut off the triangle…
Added cutout for FFC cable used by Geeetech A10M to bottom cover. Modify top cover to mount flush with LCD frame and remove buzzer and reset button cutouts. Reset still works by pressing on case, but stop accident presses, remove need for…
Prometheus 3 in 1 Filament Switcher for E3D V6 Mount I created to replace A10M mixing hotend. Uses three PC4-M10 Fittings and screws into top of E3D V6 Hotend. Insert 35mm length of 4mm bowden teflon tube to fit inside where it mounts…
Purge Bucket for Geeetech A10M A10 A20M A20 Use two M5 x 40mm Hex head screws for mounting. uses 1mm thick silicon sheet Print Settings Printer: Geeetech A10M Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: GENERIC PLA / PETG…
USB-UART Print Settings Printer: Geeetech E3D V6 Rafts: No Supports: No Resolution: 0.2 Infill: no Filament: Generic PLA White Notes: 3 walls Category: Electronics
5 in 1 PTFE Combiner Friction Fit Recommend to use PTFE Bowden Tubing of OD 4mm ID 3mm or 2.5mm Base is 8mm Ø same as ECAS04. M10 thread base to screw into E3D V6 and Titan Extruders etc similar to Added M3 Mount and 6mm Spacer. 14mm…
recommend using version with threaded inserts as it much stronger mount for cartographer 3D. https://www.printables.com/model/1138393-skeletor-mk6-with-low-profile-cartographer-threade remix to add M3x1.8mm hex nut pockets to hold…
I have removed K1 Max Cable Chain and replaced it with 500mm x 7.4 (8mm) Cable Tie. I did not want to use a riser and keep it horizontal. Cable tie mounts have a 5° upwards angle to help offset cable sag. Need to cut off the triangle tip…
I installed a RepRapDiscount FULL GRAPHIC Smart Controller on my Geeetech A10M. but i had a screen with back light but no info displayed. If i shorted pins 18 and 19 briefly to test contrast, i got info on the display but contrast was too…
Box for GM328 Component Transistor Tester. Modified to use Rotary Encoder and default component socket. Two versions of top cover one with rounded corners (Fillets) and one without. remix of http://www.thingiverse.com/thing:1277163 Print…
Purge bucket for A10M, A10, A20M, A20 with E3D V6 Hotend Mount. https://www.thingiverse.com/thing:4240378 Use two M5 x 40mm Hex head screws for mounting. 3 versions with different sizes of silicon sheet can be used 1mm, 1.5mm, 2mm (1.5mm…
Soldering Stand Base for 8586 or 936. Base for 936 will fit on top of 8586 has storage for soldering iron tips. original stand is made from thin stamped steel with no base. Print Settings Printer: Geeetech A10M Rafts: No Supports: Yes…
K1 Max Chamber Thermistor Cover Side Mount.
V slot cable clamp for FFC (Flexible Flat Cable) and IDC flat ribbon cablecrossing 2020 or 2040 extrusion. need this to keep my Geeetech LCD interface tidy and safe. Print two stand upright to go on either side of FFC to hold it. Print…
Remixed Case for LCSOFT CY7C68013A logic analyzer clone" by jamesglanville I edited OpenSCAD to remove switch and screw holes, friction fit was tight enough. (set to 0 size to remove) edited screw to allow to use counter sunk screws.…
This is a spacer to go between Seagate Go Flex USB3 SATA Hard Disk adapter to DVD/CD Rom drive. You need to cut or break off the three tabs on adapter to allow it to fit DVD rom drive. Print Settings Printer Brand: Creality Printer: K1…
I broke the Loupe small lens mount. I designed and printed a new one. ID is 18.6 mm for friction fit. Print Settings Printer: Geetech E3D V6 Rafts: No Supports: No Resolution: 0.2mm Infill: no Filament: Generic PETG, PLA, PLA-F White…
Wheelchair Brake Mount. separates front caster wheel from brake mounting. allows caster wheels to be moved to the front of wheel chair for greater wheel base and stability. also include handle to be mounted on 6mm bolts used for brake…
7mm Slim Cover Lid Box for ESP8266 Yellow Development board. I needed cover for double sided wall mounted ESP8226 DEV PCB with cable entry cut outs and to cover the power led as it too bright at night. I made it flush mounting with cut…
Did not want to drill holes in my K1 Max Frame or Panels so designed Slim 25mm Riser. K1 Max Riser for 5 PTFE Combiner.
This is a remix of Scuddy Dual Z Upgrade Kit for the Ender 3 for Geeetech A10 / A10M using a second stepper motor for Dual Z-axis. I have remove top mounting bracket from left side front mount because stepper motor will fit there, also…
A10M A10 A20M A20 X Axis Belt Clamp Print with 3 or 4 walls for strength. V2 has chamfered base. Print Settings Printer: Geeetech A10M Rafts: No Supports: No Resolution: 0.2 Infill: 18% Filament: GENERIC PLA / PETG Black Category: 3D…
Spiral to add to your Z-axis T8 rod to indicate it turning and for fun Clock Wise Rotate and Anti-Clockwise Rotate Versions Print Settings Printer: Geeetech A10M Rafts: No Supports: No Resolution: 0.2 Infill: 0% Filament: Generic PLA or…
LM2596 Mount for Low Rider MMU Insert into one of the MMU Filament Feed Body Spacer holes two Voron M3x4x5 threaded heat inserts. Insert into the LM2596 Mount larger holes two Voron M3x4x5 threaded heat inserts. Mount with 4 x M3x5mm…
To wszystkie aktualnie dostępne wyniki.
