Liczymy pasujące modele…
Print Settings Sword Wall loops: 2 Layer Height: 0.2mm Infill: 8% Sparse infill pattern: Grid Support: Tree Brim Type: Outer brim only I only use this for parts 1, 2, and 3 of the sword. Sheath Wall loops: 2 Layer Height: 0.2mm I…
Print settings first if you don't care to read the extra bits. Printer : Bambulab X1C Filament : Overture Pla Blade Normal supports 2 wall loops 30% infill Adaptive Cubic infill pattern Brim Guard 4 wall loops 20% infill Gyroid infill…
Print Settings Wall loops: 2 Layer Height: 0.2mm Infill: 3% Sparse infill pattern: Grid I used Gyroid infill on the car_hood parts to help with the area around the trigger Support: Tree Brim Type: Mouse ear I use an Outer Brim on the…
Print Settings Sword Wall loops: 2 Layer Height: 0.2mm Infill: 7% Sparse infill pattern: Grid Support: Tree Brim Type: Outer brim only Sheath Wall loops: 2 Layer Height: 0.2mm Infill: 5% or lower Sparse infill pattern: Grid Support: Tree…
Print Settings Swords Wall loops: 2 Layer Height: 0.2mm Infill: 3% Sparse infill pattern: Adaptive Cubic I only used this for the handle and blade pieces. The others were done in grid. Support: Tree Brim Type: Outer brim only Parts list…
Printer : Bambulab X1C Filament : Overture Pla General settings Wall loops: 2 Infill: 8% Sparse infile pattern: Gyroid (I just like gyroid infill) Support: Tree Normal supports should work as well. Make sure that no supports are generated…
Print Settings General Settings Infill: 3% Sparse infill pattern: Grid Wall loops: 2 Support: Tree Brim Type: Outer brim only Parts list Sword 1 5/16 threaded 36 inches long (914.4 mm) or wooden dowel Length of sword: ~39.5 inches (1003.3…
Print Settings Sonic Fin Wall loops: 3 Layer Height: 0.2mm Infill: 5% Sparse infill pattern: Gyroid Support: Tree Brim Type: Mouse ear I use an Outer Brim on the pin model Printing Instructions IMPORTANT : When forming the Storm Striker,…
Print Settings Global Settings Wall loops: 2 Layer Height: 0.2mm Infill: 3% Keep the print light since all the weight can end up on specific points Sparse infill pattern: Gyroid No particular reason. You can change this if you want.…
Print Settings Global Settings Wall loops: 2 Layer Height: 0.2mm Infill: 8% You may want to lighten this for combining with the Thunder Staff Sparse infill pattern: Gyroid No particular reason. You can change this if you want. Support:…
Print Settings Wall loops: 2 Layer Height: 0.2mm Infill: 3% Support: Normal This models is very different from the original prop. The original prop is much wider at the back of the dino head, and slims down a lot towards the nose. That…
Print Settings Wall loops: 2 Layer Height: 0.2mm Infill: 3% Can go up to 5% if you want though be mind full of the weight Sparse infill pattern: Grid Support: Any Printing Instructions Printing is very straight forward. Arrange the pieces…
Print Settings Sonic Fin Wall loops: 2 Layer Height: 0.2mm Infill: 5% Sparse infill pattern: Gyroid Support Default: tree Special cases: normal back_screw_pt1 hammer_face hammer_neck handle_short_pt1 handle_short_pt2 Brim type: Outer brim…
I have no printing or assembly instructions for this. I haven't printed this version and it's mostly for figure customizers that want the full Storm Striker in different configurations. I can't guarantee it's ability to print. The three…
Printer : Bambulab X1C Filament : Overture Pla General settings Wall loops: 3 Since the infill needs to be low to reduce weight Layer Height: 0.2mm Infill: 2% Since this is the shorter version you may be able to up this a little Sparse…
Printer : Bambulab X1C Filament : Overture Pla General settings Wall loops: 3 Since the infill needs to be low to reduce weight Layer Height: 0.2mm Infill: 1% Sparse infill pattern: Grid Support: Normal Brim Type: Outer brim only To help…
To wszystkie aktualnie dostępne wyniki.
