Liczymy pasujące modele…
Design I designed a converter for a 2.5" HDD to fit in my PS2 (with the network adapter, and the SATA mod) without it floating around. The bracket slides into place, where it holds firmly. Hardware All you'll need are some small screws to…
Will write description later, too tired, but wanted to get this all out there for everyone to use. (you'll have to print “FrontLoader_TopCover” twice) You can find the lid here: https://www.printables.com/model/110082-nes-frontloader-lid…
About Over the course of the last several months, I've been adding to my handheld collection, and needed a simple but universal way to nicely display them. This is what prompted me to make my own set of these! I have attempted to make it…
Design I had originally designed a 2.5" HDD Caddy for the PS2, and then recently found out that a certain company had used that to make a commercial remix to support 3.5" drives. All my models are released as non-commercial to avoid such…
not gonna lie, been a pita to print these on my Resin printer (Elegoo Mars 2 pro). 90% failure rate so far, but the few that were successful (or partially) allowed me to verify they are indeed a good replacement fit for the original. So…
Replacement Gear for the PC-Engine CD-Rom2 (as they have a tendency to swell up/break) Due to this being absolutely tiny, requires a SLA/Resin printer to properly print. Has been tested in well over 50 machines around the world (I have…
Step file also included for anyone who wants to tinker around with the model. I don't have a printer which fits the size of the model, so it's untested, if you do however print one yourself please let me know if it fits (and if not, I can…
SEGA Master System D-Pad Versions Please check your controller against the identifier list, to see which version is required for yours. There are 3 different variants, and they all have slightly different dimensions, making them (mostly)…
Completely built from scratch based on the original parts, as I had found the ones available don't quite perfectly fitted on my Q. I included the Tray as seperate parts, as well as a full version - you obviously only need one.…
Replicated based on the original, I intend to print them with (clear) Resin, but until I have verified the fitting please consider this a WIP . Update 2/1/2022 I found I had made some minor mistakes in the original model, causing it not…
These were modelled after the original pieces by hand (painstakingly calipering each dimension, hahaha). But I have yet to test/print them - when I do, and find any issues, I will update the models as needed. Until then consider it a WIP!…
Replicated based on the original, I intend to print them with in Resin, but until I have verified the fitting please consider this a WIP .
Simple and small print which can easily, and with a minimalist design, show off your loose cart collection! The purpose was to make something which doesn't stick out when displayed in a collection (see last image, I think that succeeded…
(if you have printed this earlier, as of 12/27/22 there is an entire new version out!) Mini-IFU (v2) Print There are 2 versions of the “Connector_Bottom” you can print (you only need one!). _v2 requires the additional…
- The one ring to play them all- Design Goal Designed a ring for the Prusa Printers flash contest. My goal was to make something nerdy yet simple/elegant, at which I think I succeeded! Printing & size The inner diameter (ID) is created at…
modelled these as practice pieces, havent tested them myself but should be good. Detail is quite small though, so best suited for Resin printing.
Instructions This bracket was designed for the Fenrir Duo as it didn't come with any mount for me - but it might also work for the original Fenrir (untested as of now - please let me know if you do, so I can update and credit here!) It's…
I printed these in 0.3mm height all in one go - which took around 4 hours to complete a full set. Result snaps together perfectly, and holds the MC's in place for easy storage. Enjoy! Update 3/4/2021 I have Added Extension pieces you can…
- The one ring to unlock them all- Design Goal Designed a ring for the Prusa Printers flash contest. My goal was to make something nerdy yet simple/elegant, at which I think I succeeded! Printing & size The inner diameter (ID) is created…
UPDATE 2/9/2025: Model is fully complete and all files have been updated to the latest versions! UPDATE 3/10/2025: Ordered a Resin printed version, and found some minor things requiring tweaking to fit perfectly, all files updated for…
full 1:1 scale shell replacement for your PC Engine
All pieces for a full SEGA Nomad replacement Shell. Includes buttons, switch, d-pad and cartridge door. If you want to get these printed through a service (instead of yourself), I also have a Shared Project up on PCBway (images show…
Recreated the Power & Reset buttons for both the round and oval versions of the Sega Saturn (including the Reset extension part found on the round original). Someone requested this one, and was a fun challenge! They've been printed and…
Design General I wanted a way to display my Gameboy cartridge collection in style , so I designed these :D It's a replica of the original cart shell, simply scaled up to 200mm (sorry mini/mini+ users [myself included], this doesn't fit on…
My friend @ZedLabz asked me for this model a while ago, and wanted me to share this with everyone. Big thanks to him for this request!
I was asked if I could help someone out with making a shell that fits a NES to Famicom converter ( non-affiliate link: https://aliexpress.com/item/1005002506286371.html ). This is a 2 part shell, which "slides" together, and is being held…
Due to minor details required (top gears mostly), best fit for resin printing. For some reason, on my Elegoo Mars 2 pro, out of the 20 I printed (in 2 batches of 10), only one ended up not working - I am unsure why, but if you end up…
Best results would be using a Resin printer, but they can also be FDM printed. For best FDM Results, I would use PrusaSlicer “Cut” feature to remove the SEGA logo from the back (0.3mm depth), so it can lay flat on the bed, and then simply…
Updates Decided to add the Updates at the top, so they are easiest to find for users that have already printed them, and are coming back for these. First of all, thanks everyone for the overwhelming support so far! A lot of you have…
Information Due to the high tolerances, it's advised to print this in Resin! Model is not optimized for FDM, as it's meant to be a replica/replacement for the original. You can order a full shell from PCBway through the Shared Project…
I have designed my own modular Glasses display stand as fun little challenge. The idea was to be able to expand it to your own needs, whether you have 2 or 10 glasses, you can "infinitely" extend the base to fit your needs! Each piece is…
These were modeled after the original by hand. I have yet to test/print them - when I do, and find any issues, I will update the models as needed. Until then consider it a WIP ! Update 12/25/21 I have been testing and printing this over…
A minimal design UMD display stand. There's 2 versions, one for single UMD display, and another for showing a set of 3. The "Stackable" variants can be used to place next to each other without a gap. The "Standalone" I imagined would be…
The Model This is the shell parts for the AES, other parts are available separate, and have been made earlier. Cartridge doors/mechanism: Buttons (Reset & Power):
Files to Print Required Print the appropriate files named "[region]_Display_Bottom" for the cartridges you want to display. Then for each additional cart, you can print the files named "[region]_Extension_Cartpiece", and simply screw them…
Printed mine at 0.3mm for testing, but will look best at 0.2mm or below! No supports needed, quick print.
Pokemon keycap set This is a full set of alphabetic keys (Cherry MX style caps) for the Unown Pokemon, which happens to depict the alphabet ;D Thought this was a perfect fit to make your keyboard a little more nerdy! Idea The idea had…
models were featured by Bob from RetroRGB on one of his livestreams ! These models are the updated versions already, which fix the issues seen in the stream. You can also order them through PCBway's shared project here:…
Got mine printed by PCBWay, and as you can see in the pictures they're a perfect fit for the original! Files are available for free to print for yourself, however if you want to order them, please consider using the PCBWay Shared Project…
Game & Watch shell All variants can be found here: https://en.wikipedia.org/wiki/List_of_Game_%26_Watch_games In the future I do hope to expand with more variants, yet G&W's generally are quite expensive to get a hold of. I'll update here…
Design General I wanted a way to display my Gameboy cartridge collection in style, so I designed these :D It's a replica of the original cart shell, simply scaled up to 200mm (sorry mini/mini+ users [myself included], this doesn't fit on…
Instructions This bracket was designed for the xStation, and covers all versions of the “phat” PS1 (1000 through 9000, even though xStation doesn't support this at the time, it'll be future compatible if it ever does!) It's designed as…
I got asked if it was possible to make an AES button set which accomodates a LED. I added both a "replica" version, which looks and functions like the original power switch, and one with a 3mm hole in the front center, to house a LED.…
I haven't had the chance to print this one yet (and it's gonna be quite a difficult print as well). Made a replacement cartridge cover/flap for the SMS2. I adjusted some tolerances from the original, so it wont shatter/break as easily…
I had the pins on the right Trigger broken off, and made a small model to fix this issue. Was printed on a Resin printer, and glued into place. This allows the tabs themselves to still flex a little bit, so you can insert it from the top…
Really simple print, no supports needed (draft angles baby!). Using the included rubber plugs (instead of screws), this will eliminate vibrational noise passed into the plastic housing. You'll need to trim this flush a bit to make it fit…
I wanted to contribute to the awesome OMVS project, so I made this AES inspired Top shell as a variant for others to use. Note: I dont have a way of testing if the model works (no printer, nor a MV1C) - so if there's anything wrong with…
Design I designed a bracket for the PC Engine GT, to hold a 3.5" LCD perfectly centered if you are doing a screen upgrade. Print LCD You need to print the "Bottom_LCD_Bracket", and then depending on the driverboard, the accompanying…
full 1:1 scale shell replacement for your CoreGrafx (PC Engine)
Will write more details here soon. Decals to go on top to look like an original are available here: https://retrofied.uk/products/sega-genesis-3-case-decal-set You can order these for yourself through the PCBway Shared Project as well:…
Files to Print Required Print the appropriate files named "[region]_Display_Bottom" for the cartridges you want to display. Then for each additional cart, you can print the files named "[region]_Extension_Cartpiece", and simply screw them…
- The one ring that should have been them all- Design Goal Designed a ring for the Prusa Printers flash contest. My goal was to make something nerdy yet simple/elegant, at which I think I succeeded! Printing & size The inner diameter (ID)…
PS2 Noctua Fan housing (NF-A6x25) Information I couldn't find any available, so decided to make my own. Idea had been to be as non-destructible as possible, so this one clips into the fan-grill on the back. Due to printed clips not being…
I remodelled the Master System 2 Power Switch, and made a variant which can fit a 5mm (or 3mm with a lot of hotglue :P) LED. I added some slots in the shaft so you can have the LED's legs stick out through there, and not have to worry…
EDFX Mini-IFU Updated my AliExpress RGBS AV Booster model to fit Krikzz' new (and better) EDFX ! Printing You'll have to see which version of the mid-section (Connector_Bottom) you'll want to print. I made 2 versions (can be found in the…
Recreated the Power & Reset buttons for the SNES Jr. Someone requested this one, and was a fun challenge! They've been printed and tested to fit as close to the originals (see the red painted versions I did)
with the small details on this, might not be best suited for regular FDM printers, and is better for Resin. This is untested for now, but will updated once I have. Update 11/2/23: I found a minor discrepancy against the original version…
Files to Print Required Print the appropriate files named "[region]_Display_Bottom" for the cartridges you want to display. Then for each additional cart, you can print the files named "[region]_Extension_Cartpiece", and simply screw them…
as usual with my button replica's, you'll have to print them in Resin, simply because they're so small and fragile.
Made a set of inserts which can be used with Cassette Tape cases to not only store , but more importantly display your games! Cassette Tape cases for GB and GBC, you'll need to cut the nubs inside the cases so it can close properly - for…
I picked up a pink PS2 Slim a while ago, which for some reason had the Bezel on top ripped off. This seemed like a nice opportunity/reason to remake that part, it's a simple enough model that made a nice quick practice for me. I have…
Design General I wanted a way to display my Gameboy cartridge collection in style, so I designed these :D It's a replica of the original cart shell, simply scaled up to 200mm (sorry mini/mini+ users [myself included], this doesn't fit on…
Shell replacement made for the PC Engine - this is the version without the switches (though funnily enough it has all the support structures for it internally already). That version however will be uploaded at a later point.
-- !WIP! -- Replacement power button, modelled after a SEGA Nomad button. Please note, due to being such a tiny object, you need support, print as slow as possible, and have the smallest possible layer height. Update 4/30/2020 Added new…
full 1:1 scale shell replacement for your CoreGrafx 2 (PC Engine)
Due to curvature and detail I don't think this will be an easy FDM print. I printed mine in Resin (no post processing in pictures, so shows a bit rough off). Difficulty will likely be getting a proper colour match with the shell - I've…
With the small details and intricacies of this model, its best suited for Resin printing (namely due to the clip and curvature in the back).
Remodelled the outer shell for a 64DD cartridge. Unfortunately this was a loaner cart, and I cannot crack it open without damage in order to model every tiny detail as usual accurately. I decided it's still good reference for anyone else…
1:1 replacement model for the PSOne (slim model PS1) gear on the laser pickup (which controls sled movement) because it's reported this specific one seems to fail more often lately. Due to small detail, this is not gonna work on FDM, and…
Added all the correct details and draft angles from the original - therefor might be best to resin print these for best detail. You'll have to BYOS (Bring Your Own Springs) for the doors however.
very small component, definitely requires a SLA/Resin printer. I added 2 versions; “original” which is a replica of the original part, and “Strengthened”, which is better suited to print at home on a hobby SLA printer (I used an Elegoo…
New Design for a Bracket designed to fit the Console5 composite LCD screen (big driverboard variant) inside the SEGA Nomad. https://console5.com/store/universal-3-5-composite-video-lcd-module-320x240.html Print Settings Printer Brand:…
Compatibility This shell is intended to work with this PCB from AliExpress . If the link is unavailable (non-affiliated), do a search for “FC 3.5 inch screen”. Printing You can print all of these supportless with the largest flat surface…
You can order this through the PCBway Shared Project as well now: https://www.pcbway.com/project/shareproject/Amiga_Pregnant_Mouse_3_button_version_f910c5ea.html Additionally, a variant of the bottom shell was added to support the Board…
Simple stand model to display your PC Engine controller (with logo variants, and cable brackets)
Due to the detail and curvature, this might be really difficult to properly print on FDM - I did my test (14" one in the photos) on a Resin Printer (Elegoo Mars 2 pro), and came out great! Original covers were borrowed from Quang from…
Threaded insert version can be printed without any supports, the clip version does need supports. I would strongly advice using the threaded insert variant, as it's much sturdier (though get some washers to alleviate the stress on the…
mini-VB Description Updates can be found below Warning : This design is made for aesthetics, and thus is not a very easy print to do. You'll have to likely experiment a bit with support and orientation, depending on your own printer.…
Modelled after the original, with the minor addition of 2 extra screw mounts for the button PCB. I have no plans to make variants in the near future, so if you need structural changes (like the screws on the other side) you can remix this…
As this is a tiny model, you'll want to use a resin printer (or order through a service like PCBway/JLCpcb) for accuracy. you need 8 small 3x1mm magnets (neodymium N52). Make sure all magnets are oriented the proper way. You can press-fit…
I added a new bracket to hold a 4010 Blower Fan to cool down the xStation when in use. This is only for the SCPH-55xx versions! Fully compatible with LaserBear's SD Card Mount! https://www.laserbear.net/products/ps1-xstation-sd-card-mount…
Update 3/23/2020: I have since making this started to learn Fusion360, and have recreated this model (v2). Along with some Quality of Life updates to the file (namely to the supports that hold the LCD to the mainboard - 1.5mm holes and…
This is an attachment that you can print to fit a G600 microscope to this microphone desk clamp/stand: https://www.amazon.nl/dp/B01N0IYZVE/?th=1 Print the Clamp twice, as you'll need one on the top and bottom. There's 2 versions of the…
Files to be able to wall-mount the Pokemon Metal Tins. Combined they form a single big picture, and I wanted to neatly display them, so I made this. There's a snap-fit version, as well as a magnetic one (my preference). You'll require 4…
These gears can be found in the following (but not limited to) consoles: SEGA/MEGA CD1 PC Engine Super CD-Rom2 PCFX Neo Geo CD (Frontloader) Amiga CD32
Remodelled 1:1 from original (and tested!). The small details in this would be best fitting for Resin printing - the ones made in the cover photo were done on an Elegoo mars 2 pro using Elegoo red translucent (ABS-like).
Instructions This bracket was designed for the GDemu, the one I had was the recent release from AliExpress, please let me know if it doesn't fit yours and I can adjust the base as required! It's designed as modular system, and the…
For the heat inserts, I used some small (4mm tall) M2 ones. Both versions need M2x5mm (max height) screws to mount the picoboot in place.
Printed mine at 0.3mm for testing, but will look best at 0.2mm or below! No supports needed, quick print. version required for printing: PocketMini_Monochrome_DisplayStand Hello Kitty Pocket Pikachu PocketMini_Color_DisplayStand Pocket…
Replacement gear for the center part of the mechanism which moves the laser assembly - specifically for the Goldstar 3DO
very minor details (once again) in this model - best fit for Resin Printing.
I made this Remix in order to have the print fit my smaller size printer (Anet AM8). Cut up into several pieces, I printed it all in 3 batches: Middle as seperate print, Left & Right side combined, and alt as 1 large print (BARELY fitting…
Someone asked me for a D-Pad replacement for the PC Engine GT, and I had some minutes spare, so modelled this one after the original :) Suggest printing it in Resin, as FDM won't give the best results Category: Video Games
Quick and simple file for printing a replacement support leg which fits the Neo Geo MVS. It's designed to fit a hex nut, similar to the original design. EDIT: re-uploaded file for the right size Category: Video Games
My friend needed something made to allow him to connect up a standard hose to his pump, so I quickly measured and modelled this adapter. I figured there might be other people out there who can use this, so may as well share this with…
Modelled in 2 parts for Strength! Print the hinge sideways, to make advantage of the strength of the layers, as the piece needs to bend to get into place (and printing up-right will likely result in the piece snapping off!). First Picture…
This is a Shell for the 4" (widescreen) AliExpress SNES LCD Screen , specifically to fit the PAL version of the SNES, or the Japanese Super Famicom (SFC). US NTSC version can be found here Printing I have include 2 variants of the bottom…
Simple backplate replacement, allowing for either a mini-din or megadrive/genesis 2 socket to be installed. I used this one, because it has a nice breakout board with it (did have to file to top flush a little bit);…
C64 keys Row layout filenames start from the top to bottom, special keys are named. Known missing is the spacebar - will update here when done. Please note the prints in the images are done a few years ago on a printer that was pretty…
Designed in 2 parts, which you'll have to glue together, otherwise the offset difference cause the flat front piece to require supports when printed (and wouldn't have a nice looking finish), which would be a little bit of a waste of…
![Intellivision no-cut (AV) mod [clip-on & threaded insert versions]](https://media.printables.com/media/prints/530236/images/4281269_1220d21c-c38f-406b-98f6-0c2649ae21be/f07sgacwyba-wwc.jpg)
