Liczymy pasujące modele…
Bobbin originally designed for classic Elna sewing machines but should be customizable to work for any sewing machine. Our Elna machine came with one metal bobbin that was approximately 21 x 11 mm. This bobbin is by default 20.1 x 10.8 mm…
I misplaced the blade fastening screw for my Chef's Choice 615 Electric Meat Slicer. I made a replacement part to match based on measurements (I did not have the original part to compare to). So this is not a 100% exact match but it…
This is to repair the broken off male connectors on a Brio-compatible dual train signal. Print with supports. Note that the part that inserts into the toy is set for 12mm which might be too long for your use case. It's also a very tight…
The California Air Tools 1P1060S compressor is well reviewed as being quiet compared to the competition however due to vibration, if you're using this inside, it's still very loud. I found if I held the compressor in the air while it was…
I needed a way to compare one side of the z-axis level to the other side on my 3D printer as it droops when the steppers are powered off. I ordered parts to link the z-axis lead screws together however in the meantime, this tool makes it…
Elna Presser Bar Lifter #411461-10 I recommend printing with supports at 100% infill as the middle of the presser bar has an angle step which is a weak spot. The part is very similar to the original Elna one however the arm does not get…
A 4.25" or 108mm vent for RV exteriors. Category: Outdoor & Garden
Some prints to attach a 75mmx30mm centrifugal fan to the Thetford Electra Magic toilet. These designs were created for use with the toilet as it is mounted in the TrailManor travel trailer however some of them might be useful in other…
If you happen to have the same fridge as me, there are two screws put into the door surface right between the upper freezer and lower fridge. I believe they are so you can swap the direction the fridge opens from side to side. They are…
Some simple wheels for this forklift: https://www.thingiverse.com/thing:1694824 Note I scaled it up a bit so you'll need to scale it to match whatever size you print your forklift at. Print Settings Printer: Creality CR-10S Resolution:…
The Bruder recycling/garbage truck had a broken mechanism. On the rear of the truck, you can rotate the red knob (left side of rear) and it will scoop up the garbage dumped into the back and put in into the middle storage area (that…
This is a mounting bracket for a PTC element. It happens to fit a 250w 120v PTC element found in a small desk heater -- I don't know how universal it is. This is more of a building block you can edit to make what you want. I'm going to…
A smaller handle/lever for your 25mm (1"), 19mm (3/4") or 13mm (1/2") TruDesign ball valve. Makes it easier to fit the ball valves in tight spaces where the original handle will not fit. Note that the original screw and screw cap are…
The sliding patio doors on our sailing catamaran (2003 Privilege 465 EC) were no longer functioning properly in that they were hard to slid open and closed. I took the doors off and discovered the bearings on the wheels had failed and the…
I needed some metal balls to put in small containers of acrylic craft paint to mix them up. Most colors are fine but the metallics are hard to mix. I needed around 7-8mm sized ball bearings but I only had 4.5mm metal balls (used in BB or…
The Vetus raw water strainers are secured by two screws on the built in bracket. The screws are often difficult to access and sometimes the bracket is damaged. This part can be used with epoxy to repair the bracket. Or you can use it to…
On the front of the motor is a choke knob. That knob connects to a metal shaft. The metal shaft connects to a plastic adapter that has an expanding part that clips onto the metal knob of the choke mechanism on the carburetor. That bit of…
To wszystkie aktualnie dostępne wyniki.
