Liczymy pasujące modele…
This is a scaled version of Zagatorz's amazing fidget toy. My friend had printed another version of the spiral passthrough that would break when dropped, so when I found Zagatorz's one with the thick base, I was elated! However, the shape…
This is a very simple OpenSCAD program that generates desired text in your desired font. You can use the generated file or code any way you'd like, such as adding it to a model you've already made. There is also an option to render the…
I had printed some other center skid plates for my Typhon 6s but none of them were as durable as I would have liked, especially as I wanted an ultra strong one for my Fireteam as well. Thus, I made this one which uses 4 M4x12 BCS screws…
This is a remix to allow mounting the GPS with just Velcro or another similar material instead of clips. Cutouts are on both sides to allow easy removal, and it's also possible to charge the GPS with a low profile USB-C cable. Print…
I wanted to keep my new BasherSkinz chassis protector from getting all scratched up. so I made these side skid bars to help protect the chassis when hitting jumps and curbs. There are two versions available; a 5mm version for serious…
I wanted more control over downforce on my Arrma Limitless as I use it as both a drift car and a speed run car, and the only commercial kit I could find was way too expensive. So I decided to do it myself, and I made this kit which…
I needed a longer shock spacer for my Mojave 4s and so I made some in Tinkercad and made a bunch of different sizes. Spacers have the exact same width and inner diameter as stock, but with assorted heights to tune your suspension. There…
I was a little unhappy at the somewhat sloppy servo saver on my Arrma Fireteam, and the design of the bellcrank prevents you from simply tightening it. Thus, I made these spacers which fit between the factory metal washers and drastically…
This holder allows for secure mounting of Hobbywing Max G2 series power switches in the same position as the stock Spektrum power switch. The switch is supposed to tightly pop into place but you could also use a dab of glue if it isn't…
I installed a Max6 combo in my 100+mph Typhon and the body was too low to fit the fans and due to the poor fit it never looked great. I found some lifted body posts, but they were too high, so I adjusted it to be only slightly higher than…
Even though I would apply excessive amounts of orange Permatex (Loctite) to my Traxxas Sledge pinion gear, it kept sliding down the motor shaft inside the motor mount where I couldn't get to the set screw, so I made these spacers which…
These super-durable wing mounts allow you to mount larger wings (such as the Talion wing) on the Arrma Typhon. This should work on Talion too as p/n is the same. I wanted to mount the #ARAC9608 wing on my Typhon 6s but it wouldn't fit…
This mount allows you to mount a Max8 ESC and its switch into a Mojave 4s (and possibly other Arrma 4s models too). It's nothing too fancy, but it does work well and mounts securely. Since the Max8 is wider than the mounting holes, the…
I wanted a way to mount my Bittydesign AR8-GT3 body on my Arrma Infraction without horrid body clips, so I designed a magnetic body mounting system that works perfectly. The front of the body is held very securely by 8 10lb magnets (4 in…
I recently added a reversed GPM motor mount to my Sledge so I could run a Max6 combo. However, I couldn't find a good way to mount the ESC in the front of the car, so I grabbed a standard Hobbywing mounting plate and got to work in…
This is a very simple mount for a JR/Futaba/servo connector. It's basic and the only way it will likely be useful is if you add it to another design. Category: Hobby
My Mojave 4s center driveshaft bearing wouldn't fit in the stock location as the TP 4050 that I've installed is slightly too large to fit the bearing in the normal spot. To fix this, I made a custom mount that securely holds the…
I found an amazing design from chrismofer here ( https://www.thingiverse.com/thing:5358689 ) but the shims were a bit too high for my application as I'm using custom rock sliders, so I put the file in TinkerCAD and made some assorted…
On my Arrma Limitless spool the spur gear would occasionally slide down the shaft away from the pinion under heavy load. These spacers slide onto the spool with the spur gear to prevent that. Print Settings Printer Brand: ELEGOO Printer:…
When I installed 6.5mm hex extenders on my Typhon, the screw pins wouldn't fit the driveshaft so I had to use the standard pins. Since I was worried about the pins falling out, I made this sleeve that slides over the hex behind the tire…
I needed a replacement mount for my TRX-4's Pro Scale lighting power module, so I made one in Tinkercad which works great. I also included a version that works on cars with lifted rock sliders (fits up to 9mm spacers). Print Settings…
This is a pretty simple dummy T-Bar. It is not the correct length nor does it have any holes for mounting in the car. (Neither do I recommend installing it, as it would likely break and cause chassis bending) I simply made it to help make…
These are some body mounts I made to eliminate body clips on my Typhon 6s. They are made to fit 3/4" x 1/8" countersunk round magnets. I used ones from K&J Magnetics, which you can get here -…
This is a nice mount to install a JR power connector into the Traxxas Sledge. I designed it so I could easily connect and disconnect my custom light kit. It slides firmly onto the T-bar and you can install a female JR connector into it…
This is a simple mount that attaches to the top of the Arrma 4s RX box. It holds a Hobbywing ESC power button and the AGFRC V3 aluminum gyro. There is also a version that just holds the Hobbywing button. Normally it's a press fit, but you…
I made this to hold silica gel packets (I use the Wisedry 50g packets) inside my filament storage box. Not the fanciest, but it does work and makes it easy to access the packets for drying. Print Settings Printer Brand: ELEGOO Printer:…
This is a nice 4 way wrench holder that firmly fits the Traxxas wheel wrench. I can't claim full credit, as I took the design from someone else and added a little snap onto the top section to hold the wrench more firmly without risking it…
These are front and rear beadlock rings for the new 5IVE-TE 3.0. They use the same length and type of screws as the originals. I would suggest printing at 100% infill in a tough filament.
To wszystkie aktualnie dostępne wyniki.
