Liczymy pasujące modele…
The original auger looked challenging to mount accurately onto the servo as presented, plus it was non-manifold. It also looks to be quite a workout for an FDM printer, although I didn't try. This model fixes the holes and adds a mount…
Simplify3D wasn't able to slice the original correctly so I ran it through Meshmixer and it seemed to fix things. I noticed the gaps at the tops of the loop sections were supposed to be thin walls but it turns out the openings really help…
I was using Leo_N's filament guide but then suddenly my Ninjaflex was folding under the idler pulley. I designed this to sit a little closer to the extruder gear as well as having adjustable positioning with an elongated mounting hole.…
I modelled the hangers to include some M6 threads and I also made some printable M6x30 screws. There are three hangers with different tolerances for the screw/thread gaps. I also included the Fusion 360 file for further customization. If…
Update: May 20, 2024 Over time I've discovered that there is not enough airflow to the heat sink, and jams occur more often than they should. A hole on the level sensor side of the enclosure should be sufficient. Some other shortcomings:…
I added some threads to the original design as well as adding some material to buffer the filament from any potential rubbing against the fitting edge. The size was scaled up 104% in the X and Y directions and 101% in the Z direction. I…
This design is a remix of the original collector cone piece from the Modular Hydroponic Tower Garden by boundarycondition. It allows the tower to be separate from the rest of the system. It uses M5 bolts to attach it to a base. Print…
This is an updated thing, the original one can be found here. The cooling fan duct is the Mistral 2.1a. This main goal of this sensor mount is to bring the SN04 into a position where the entire bed can be measured for mesh-leveling while…
I liked the concept of this design but found support removal impossible. To eliminate the necessity for supports I cut the handle in half. The files are large to ensure accuracy and the top half of the handle needs to be flipped over to…
I needed to move everything closer to the breakout board after upgrading to the BTT SKR 1.4 Turbo mainboard. These brackets use some of the M4 holes on the electronics enclosure and power supply to mount everything to the side of the 2040…
Updated thing with fan shroud here. Compatible sensor sled for use with the BLTouch/3DTouch here. My A8 came with the SN04 sensor and I have used several of the sensor mounts available on this site to try and make it more user-friendly. I…
Update: Jan. 10th, 2022- Corrected length of filament block bearing shaft screws. Was 12mm, they are actually M2.5x10mm. Revised bearing block model and added a 20mm length of PTFE tubing to the build. Without the tubing to guide the…
I mirrored the mirror of the fan shroud/BLTouch mount from LickenMick's design. Works well, thanks for the original design to remix. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 15%…
Remixed for 25mm fan using M3 hardware: https://www.thingiverse.com/thing:3624012 I needed something to muffle the outrageously noisy fan I selected. It seems to have helped both the noise and the airflow. It could always just be the hope…
I had a problem getting the servo to sit correctly; I think I must be using a servo with different dimensions than the one that the design was based around. The spacer slides in the notch at the bottom of the electronics enclosure. Insert…
To wszystkie aktualnie dostępne wyniki.
![Adjustable Mesh-leveling-friendly SN04 Auto-level Sensor Mount for A8 (no heatsink, no fan [yet])](https://media.printables.com/media/prints/283301/images/2504840_1455cfae-33c8-44d9-ab92-b6aba90dcdab/05d3ffd5239f926b283b4e630366a0c1_display_large_283301.jpg)
