Liczymy pasujące modele…
Pretty simple designs. Not perfect but work well. I made these because the other ones I was seeing required purchasing special screws from the hardware store. I haven't verified all the model numbers in the title but they should be good.…
Made the original model with a project in mind that ended up not happening. Decided to make more sizes since it was easy enough to do. I have printed the 40mm sphere and it printed nicely. Basically made spheres in tinkercad going up in 5…
Pretty simple design. The gap measurement is the distance between the prongs. If you add 32mm to that number you get the actual length end to end. Example the 15mm gap model is actually 47mm long. I widened the models that are 45mm and up…
This is something I designed from scratch to use in a Sliger CX2177a case I used to build a server. This will allow you to mount a set of three 2.5" drives up to 15mm thick attached to the front fans on the case. If you are using an ATX…
I made these for the SanDisk Ultra Dual Drive Luxe USB A C flash drives. The cases will hold up to 3 of them total. Opening for drives is 46 x 13.5 mm and 9 mm deep. External dimensions is 56 mm square and 15 mm tall for rev 2 and 3. I…
IMPORTANT YOU NEED THE WASHER TO PREVENT DAMAGE TO YOUR LAPTOP! I made this so I could put a B+M key M.2 NVMe SSD in the WAN slot on my Lenovo Thinkpad T14 Gen1 Ryzen laptop. If compatible the slot is wired for PCIe x2. If the WAN slot is…
Simple replacement foot for Dell PowerEdge T320, T420, and T640 server. Might be compatible with other models but I just have those three to verify. Other possible compatible models are T620 T630 T430 T440 T330 T340. You will need a fine…
This is a remix of my Compact case for MikroTik wAP AC access point model. That model was device specific and purpose designed. I removed the holes for the access point features along with the board supports in the case. I expanded the…
So these aren't really meant to be printed as is but this is me sharing the raw components I made to design custom gopro mounts. I made these pieces in tinkercad and am using them as parts to work with to design my own mounts. This will…
Pretty simple design. I wanted something that was stackable and optimized for shipping. I made a single CPU version and a 9 CPU version. All versions are stackable. The one with “Tight stack fit” in the name was a first revision of the 9…
Needed something that would allow me to get some space between my tripod head and a mount I am using. Using just a screw to extend it wouldn't be very stable or strong so I decided to make something that would give me height and stability…
Plastic adapter for Lenovo ThinkCentre M600 and M700 tiny PCs to mount 2.5" SSD or hard drive. Not the same design as the original part but it is designed for easy 3D printing while maintaining the same general functionality. You will…
I thought it would be nice to have a metric version of these. I started with a 10x20x30mm version and scaled things up. They follow the 1x 2x 3x ratio for the side dimensions. Hole diameter is half of the width of the smallest size. For…
I decided I wanted a custom gopro mount that will allow me to do horizontal and vertical recording at the same time without using multiple adapters. The dual Gopro mounts I did find would put the gopros in the same general orientation.…
Pretty simple design. 25mm diameter at the base and tapers to 20mm top. It is 7mm tall. Screw opening diameter is 9mm and the small hole for threads is 4mm. There is a 3mm gap between the stop for the screw head and the bottom of the…
My hollow spheres are popular so I decided to work on other shapes as well. Basically made pyramids in tinkercad going up in 5 mm increments then cut a hole inside with a pyramid that was 5 mm smaller and centered inside. The size of the…
This was a quick design I slapped together but it works well. As long as your cardboard tube has clean edges they should slip on. This will work with cardboard tubes from things like rolls of painters tape, packing tape, or bubble wrap.…
My hollow spheres are popular so I decided to work on other shapes as well. Basically made hemispheres in tinkercad going up in 5 mm increments then cut a hole inside with a hemisphere that was 5 mm smaller and centered inside. The size…
This design mostly works but the ergonomics aren't the best and I didn't realize how much variance there is in McDonalds sauce cups. I haven't fully tested it and only did a partial test print. The design should be generally ok though. I…
My hollow spheres are popular so I decided to work on other shapes as well. Basically made cones in tinkercad going up in 5 mm increments then cut a hole inside with a cone that was 5 mm smaller and centered inside. The size of the model…
Designed some replacement spacers for the SilverStone Hydrogon D140 ARGB CPU cooler. They should be pretty darn close to the originals dimensionally. I still have my originals but the geometry was simple enough to whip these up for anyone…
Not a great design but good enough. It is meant for the bottom side of the case. (The bigger side that has feet) Dimensions are slightly off but it fits. Original foot clips in but I didn't think that would work with the limitations of 3D…
Really simple design. I think it took me like 2 minutes to make. This replaces the little plastic piece that goes over the external mini WIFI antenna connector for the M710q and M720q Tiny. Prints quickly and no supports are needed. It is…
I had fun with this design and spent way too much time on it. I wanted a smaller housing for my Mikrotik wAP AC for a homelab project. The Mikrotik wAP AC Cover (Vent holes with round corners) is my final design that I went with. Since I…
Really simple design. The old locking clip mount breaks easily so I just made a holder to sit it in. Probably not ideal for outdoor use but for indoor use it will work great. It has 2 holes in it for drywall screw mounting. You can also…
Nothing special by any means. Been trying to make some small pots to put baby aloe vera plants in. Turned out a little smaller than I was expecting. I think it would be nice for succulents or it might look cool with a tea light inside…
I made this to hold a remote for the Silverstone LSB02-E I got as a review sample. I made it so you can mount it with standard drywall/wood screws, 10mm diameter round 3mm thick magnets, or just double side tape it. I imagine this will…
I only printed a skeletonized version of this to verify dimensions and fitment. Dimensions are correct but I didn't do anything to optimize the model further. The plate is 5 mm thick the rack ear is 3.5mm thick. Overall footprint is 87.88…
This is a bit of a specialized piece but you never know. I made this to work with a 1U shelf I had. I wanted something to span the gap between my Cisco WS-C3560CX-12PD-S switch and the other edge of the rack shelf. There are 3 spots for…
These should work with most vintage Emachines towers of the DDR memory era. The ones with the black or grey case and rounded silver front. Honestly you could also use them with any other computer case as well though. You might want to…
To wszystkie aktualnie dostępne wyniki.
