Liczymy pasujące modele…
A box for your NanoVNA-H4. Includes room at the SMA connectors for you to leave your adapters on the VNA if you like (I have BNC adapters on mine). Fits the SMA calibration standards and has lots of storage room under the NanoVNA and in…
Note: a revised overkill version exists now: Original model: Includes a model for the front and rear seats. EDIT: Sep. 8, 2024 - Added a “rear middle seat” hanger with enough droop to reach under the middle seat head rest. Headrest peg…
I got tired of my snow shovel sliding around the bed, so made some simple hangers to mount the shovel to the OEM strut rails. Includes two (2) types of strut blocks: T-Slot Block = Most secure, but must slide in the whole way. If you have…
I wanted a way to reliably and simply mount an SSD1306 OLED board of the standard dimensions to my hobby enclosure, and this fulfills that need. Keeps the OLED display square and tight to the edges and doesn't wiggle around. Top Hat: for…
Options provided for ½", ¾", 1", 1-¼", 1-½", 2" knockout holes. Simple prints that thread together perfectly, use the included nut, thumbwheel, or use your own 3/8-UNC nuts. Dimensions: These are sized for standard KO's, but all…
This is a design for a hex beam antenna for 6-20M bands. My build uses a Hastings telescoping lineman stick which you likely won't use, in which case this is better used as inspiration for your build (and not a direct-print package)…
Used to attach your telescopic fishing rod to the end of a tripod or post for portable / QRP ham radio operations. Also includes a tip that can be slid over the top of your rod to connect a single antenna cable/balun, or a dipole type. My…
A modification of lewosh's excellent model with the following changes: Added screw holes to mount the PWM controller. Added mounts for a Makita 18V battery holder. Also made the model taller to fit. Added mounts for an adjustable power…
Needed a set of wall-mounts for my Fluke 87V and Fluke 177. Went through a few revisions so that they slide on perfectly, stay secure without moving, but also pop off easily when you want to remove the meter. Mounting holes sized for M4…
A remix of NiclasS's remix of Rokkdaddy's camera mount, does the job of mounting a G4 Instant camera to the MK4. I used NiclasS's base and offset the camera mount further back due to how far the G4 Instant sticks out, and added a camera…
These headband brackets allow you to clip a mining headlamp onto a headband for use around the house / etc. Based on the same measurements as the MSA 15244 hard hat bracket. I'm using an NLT Polaris cap lamp. Design Notes: Slotted for a…
This panel mounts under your for connectors or whatever (I used 3 x XT60 DC connectors and 2 x BNC Coax connectors for portable HAM radio). Fits my Gen 3 Tacoma Sport passenger seat with no power controls. You can try on other seat…
Redesigned my hardhat hook to fit my specific hardhat style perfectly . Cradles the hardhat better so it doesn't deform the plastic in hot weather, and makes it easy to toss the hardhat on + it doesn't rattle or slide around. Prints in 2…
Disclaimer: This was a personal project, and I'm happy with how it turned out but was also a good project to test and learn things. If your only goal is to monitor a drybox or make a dryer with a minimum of effort, this is not a project…
Uses 2 x AA batteries and a BS-612 PIR sensor to drive a simple relay and provide dry contacts to control whatever you need. This one is used to control Halloween decorations. Electrical: Observe the contact rating of your chosen relay (I…
A simple Balun, easy to wire up and solder. No cover, just a simple thing for QRP / portable usage. Coax & ferrite core based on HF <30MHz designs. Use FT114-43 ferrite core (aka: Fair-Rite # 5943001001 ) Coax is type RG-174 BNC jack…
I sized this for my Balance Plus broom, but you can open the attached .f3d file in Fusion and adjust the internal diameters to friction fit whatever size your broom is. Buy 1" Teflon furniture sliders from Canadian Tire or Home Depot,…
NOTICE: Assembling these took about 30 minutes per candle, and consumed materials worth ~$2 per candle (including batteries). Building these is a large commitment so read through and make sure you're willing to put up with the fussiness.…
Dunno what type of Rubbermaid hamper this is, but the handles seem to go missing. This replacement handle snaps right into place, no glue, etc. I printed mine in PETG, upright with supports (see photos of slicer) so that the outside…
Sized for standard 1" ID nozzles, like the Atten ST-862D. Wall-mounts with a single screw hole (sized for #10 screw). Options: Includes holders for 4, 6, or 8 nozzles. Includes .f3d file so you can modify as needed. You can press-fit the…
A panel-mount adapter sized to perfectly fit the BS-612 sensor paired with a lens, sold by Adafruit as #5578. The “hat” is threaded over wires or leads and presses the sensor lens against an enclosure, secured with two (2) M3 screws and…
I made these panels to add 12V power sockets into my truck bed. Includes a fuse panel and is connected to my chassis battery and an auxiliary battery in the truck bed. The switch panel has 12V sockets and a voltmeter, with 2-position…
Fits two (2) total packages (48 fertilizer sticks), with the included plastic spike. Included .f3d archive file so you can modify if needed.
A perfectly dimensionally accurate blank that fits the Gen 3 hole in the bed, left for optional OEM lights. Snaps in exactly like the OEM blanking plate. Open the blank in Fusion and modify it for whatever you need to do. I've included an…
To wszystkie aktualnie dostępne wyniki.
