100 modeli
To improve cooling and performance, I designed additional feet for my Lenovo P15 (2nd generation). This prevents the warm air from accumulating so much under the motherboard. The keyboard's angle is only changed very slightly, which means…
Wydruk około 2,87 €–3,51 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Pull the metal stud out of the wheels and press into the feet. Printed with: 0.15mm layer hight, 6 top and 5 bottom layers, 30% infill and 3 parameters.
Wydruk około 9,18 €–11,22 € nettoWstępna wycena jednego wariantu
Flsun Super Racer SR Feets for more stability 🦾 The model is at the exact same height as the original feets but you can increase or decrease the height easily in you slicer. Printed in TPU 82A and used in this video: Remixed from:…
Whenever you want to have your Twotrees laser engraver higher...
Just a bit higher ;-) I've added rubber feets to the hardfeets. Printed in filaflex with 10% Concentric Infill and Top/Bottomlayer fill pattern in Archimedean Chords. UPDATE 29.09.2019: added gcode to use with filaflex. Print instructions…
Feetattachments with holes for moung it on the Sculpfun S9 and simular frames. It has holes to mount the feets onto the Frame (by M5 screws) and holes to mount it on a Surface like a Table or wooden board. Additional its designt to take…
Since my Q1 pro is on a server rack which has a fan in the top that blows air outwards. As the distance between the server enclosure and the Q1 pro was too small, I thought about designing new feet. As it was unfortunately not possible to…
The feet on my V3 PLUS were not quite flat, I designed this, it fits over the periphery of the original feet, with a flare on the bottom to deform it to release gravity, and now my machine runs very stable! Print settings: material…
Füsse bzw. Halterungen für einen Atomstack-Laser zur Befestigung einer Grundplatte.
I did these to be able to clean under the sofa with the vacuum cleaner. Hight 75mm
DJI Avata landing feets I need more space between ground and the avata, so i created this landing feets. i printed it wit PETG https://amzn.to/3TztjKk If u want a more special one u can take a look here…
Little Gadged for the DJI Avata. If u need unique landing feets… ;-) i used orange PETG for printing https://amzn.to/3TztjKk If u want a more unobtrusive Landing Gear take a look at this one:…
Feets for the Fujitsu Futro s740 thin client computer. Just use them in place of the original ones FreeCad files are added, so you are free to midify it to your needs. The repair connector is used in case the original studs are broken…
if you love like me the Vibration damper system from Rui Carmo ( https://www.prusaprinters.org/fr/prints/59947-new-version-squashball-mk3smk3s-vibration-damper-v ) and if you also love the Side drawers from djedje_zr7 (…
After making my sweep bling low profile with choc 1s, I couldn't decide whether I'm going with no case at all, with only the case, or with a stand. So I tried them all, each with their own rubber feets attached. This does make the whole…
Adjustable feets to be used with anything really! Print without supports!
Introducing M3/M4 Nut/Insert Miniature Vice feets with optional O-Rings I used the power of nuts and inserts and added the option of using M3 screws, which are generally more popular. I also added optional O-rings, which improve the grip…
verstärkte Füße für die Tastatur. Gedruckt in PLA ist es etwas schwer zu installieren, dafür hält es bei mir ewig. reinforced feet for keyboard. Printed in PLA, it's a little difficult to install, but it lasts forever for me.
Meant to be a tight fit so you'll need to hammer it softly into place. Feets are intentionally slanted slightly downwards at about a 3.3 angle. Printed at 0.2mm print height
I have make cutout for true functional anti-vibration feet model from schuetzi99 . The cutout fits for MK4 standard feet with slip protection version (URL to the right STL). I have used the PrusaSlicer 2.7.0 only so the .3mf file is a bit…
I made this because of poor stability on foam feet. Print 3x prusa_mini_damper_feet_3x.stl Print 1x prusa_mini_damper_feet_back_1x.stl Print 1x 5th_feet_Z_support.stl Use M5 screws to fit it in profiles. And I used this silentblocks as…
I designed and I am using these feets since the begining with my Prusa MK3S. It was my first conception. Now I can sleep near the printer. VERY EFFICIENT, but you need your spool to be not attached to the frame, because it makes the…
feets for a metal rig FreeCad files added, to allow easy modification Category: Household
A small model for my Geneve XL. Designed for the original countersink screws that came with the stand. I wanted to replace the stand with small feet to have the projector a bit lower. I used the 30 mm version with the original power cord.…
Designed for short M3 Bolts (M3 x 10 ) combined with T-Nuts. I used my remix of Fallen's model( https://www.prusaprinters.org/prints/127404-3030-m3-drop-in-t-nut-remix ) The feet is 25mm tall, so it raises the printer abit…
This feet attaches to the Prusa i3 MK3 (or similar 3030 extrusion profiles). It holds a regular squash ball and lowers the amount of vibration going into the ground. The shape resembles the overall design language of the Prusa printers.…
For the (Un)original Prusa Drybox ( https://www.printables.com/de/model/551828-unoriginal-prusa-drybox ) extened feets I had to rise it a bit higher than the original feets to have more clearance underneath for ptfe tubing and an…
To secure the feets in place you can use hot glue in the grooves on the top
Replacement feets for the Sound Blaster X Katana soundbar to raise it a little more from the table. Category: Audio
Remix of MovieMagic's Optimus Prime model
height adjustable by rotating bottom part top (1) and bottom (2) parts printed in PLA or PETG brim (2) printed with TPU or resin-like plastic
After one of my mainboard fans failed I wanted to raise the KE and SE to get more clearance. This is the KE and SE wide feet version. Printed in PLA 0.16mm, 3 walls and 4top and bottom.
I have designed decoupling feets for the orignal feets of the Prusa Box. Just stick a few pads underneath and everything is a little quieter and produces less vibrations.
Feets for Ender 3 using squash balls
These feet use 50 durometer, 30 and 40mm half-spheres made out of the visco-elastic urethane rubber "Sorbothane" to reduce the amount of conducted vibrations by a lot, without the problems of self-induced oscillation of more springy…
Alcaplast APZ13-DOUBLE9 feets to replace the factory ones if they break It is a quite fast print and so far it holds I have printed it in PETG Print it on its side layer height 0,2
Feets modified to hang the Sonic Pad verticaly on the 2020 extrusion Category: 3D Printer Accessories
I wasn't happy when my kid was dragging the chair which was making loud rattling noises so I've decided to use flat feet where I could add floor protectors. And since the legs wasn't perpendicular to the floor and I didn't wanted to deal…
Original model with a touch of fun
MK2.5S ABS 0.2 mm 20% linear advance 1 x hexagonal head screw m8 x 60 3 x flat washer steel M8 3 x Hexa nuts M8
Added feets and hands for fun
Vibration damping feet for the Creality CR10 series. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Innofil Innoflex 45 Silver Notes: Any material flexible material…
Simple but very nice model, print in TPU
SSUPD Meshroom S feets in 15, 20, 25, 45, 50, 55 and 60mm. Should also work well with NCase M2 and M3. Needed hardware (multiply by the number of feets) 1x M3x5x4 heatset 1x M3 bolt of 6, 8 or 10mm length (OPTIONAL) 1x M3 shim/washer,…
Die Originalen Füße von den waren scheiße, hab die vom Green Hornet nachgemacht.
Reuse your old silicone bed mounts into four very grippy feets. I was tired of my Ender 3 V2 moving on it's own with the stock bad feets. I also needed to raise the whole machine to convert it to the Voron theme. So I took some time in…
custom а feets for Cougar QBX. Unlike the stock ones, they do not block the air flow for the video card. I didn't want to make holes in the case to fit the front feets, so I used double-sided tape. Hind feets are installed in stock seats.…
The small arms are a bit weak and broke with PLA. In PETG it worked fine. Fusion file is included so feel free to remix it :)
Dieses Modell ist passend zum Lenovo Legion 7 15IMH. Es ermöglicht dem Notebook durch das abheben von der Tischplatte eine massiv bessere Belüftung vom Gerät. Ich empfehlen den Druck mit TPU da damit das Gerät auch nicht wegrutscht beim…
Print 2 of each parts, assemble (it's better to put some glue, but not mandatory), and enjoy ! :) [Last edit] Added a reinforced version of feets for better stability and heat resistance: pied-v1a-h20.stl [/Last edit] Print instructions…
Endplug Replacement for 25mm stainless steel square tubes, like the IKEA Kramfors leather sofa. Use PETG or better ASA and 10 vertical walls/perimeters (Alternatively 100% infill). They hold very well and they are slightly higher than the…
Set of Ikea Norden 15mm feets with screw holes. To elevate the Table a little bit. Necessary in my case for my vacuum robot.
I've been using the Hofftari feet for my desktop printers, but on some prints it tends to wiggle some, got an idea to try squash balls for vibration damping, since they are made of a rubber used at industrial vibration damping…
These parts are screwed in a systainer plate and the compressor frame. It allows attaching systainers above the compressor. The top upper front metal bolts are replaced for the front connectors, while 4 ¾'' countersink screws hold the…
The original table feet were too slippery, so I drew overshoes and printed them in TPU.
I removed the inside base of the Feets file. Should still be just as functional and reduce filament and speed up print time. Lite Edit based off the work from @godsci The original files can be found here:
The stock fan was too loud for my liking, so I replaced it with a 120mm PC fan. to allow for sufficient airflow those feet will lift the printer 35mm + 5mm if you add some cork underneath it. I attached them with hotglue.
This gadget is for camper, who camp there, were the ground is sandy and the normal feets can stuck in the dirt. It gives your marquee more stability.
My workbench has plastic springs to hold the 4 feets after retraction, 3 were broken, so I designed this replacement. printed in PETG for strength: n04 L0,2 6 walls 70% infill in case you have the dame workbench, this may help you too.
Feets for 3030 Mesh Cuboid enclosure from RatRig I have bought this Mesh 3030 Enclosure Cuboid from RatRig : https://www.ratrig.com/modularenclosuresystem/enclosure-standard.html But it comes without feet… 3030 extruded aluminium can easy…
add 2 parts to allow screwable feet
You can easily find dirt cheap Via C7 terminals from Wyse. They can work as a retro machine or perform other functions. More often than not you can buy them without power supply and any stand or feets. I designed mine to be easy to print,…
I got an older Jysk Tistrup desk that i needed to get 5 mm higher, so it is in level with my second desk. They fit perfect,and doesnt need any glue to hold them in place. Can also be used as replacement if the original rubber feets are…
These functional feet are designed to elevate the IKEA DRAGAN soap dispenser and toothbrush holder slightly above the surface, keeping the bamboo dry and preventing water absorption. This simple addition prolongs the lifespan of the…
After purchasing and printing risers for the dryer, it turned out that I have a newer version where the two metal rods are no longer present and have been replaced by four feet. As a result, I had to design an adapter. It should be…
just some feeds for the CineQueen
Print it in PETG. Use double sided tape to keep the feets in position.
Es wird zusätzlich noch folgendes benötigt: 2x => M3 x 40 Zylinderkopfschraube 2x => M3 Mutter Gedruckt wurde mit Stützenfunktion, Material PETG. Das Original habe ich nur gezeichnet aber nie gedruckt, da die Lamellen, die dazu dienen,…
This kit made for QIDI Plus 4 with turned-off and removed stock auto z-offset system (QIDI Plus 4 with added Cartographer/Beacon, QIDI Plus 4 modded for bed leveling with inductive sensor only, etc.). Anyway, all modifications you will do…
Wir haben eine Tisch Erhöhung für unseren Esstisch gebraucht um unsere kalten Platten aufzustellen. Werde diese Platten nun weiterverwenden als Monitorerhöhung am Schreibtisch. Die Oberteile werden einfach nur in die Füsse mit eingesteckt…
Since I had to put my CODA router sideways I started facing a lot of issues with internet connectivity due to overheating, so I printed some nice feet to increase airflow and my problems were solved. How to use: Just print 4 of there and…
Feets / legs for Ikea Besta corpus with a height of 10cm. One feet needs one hexagonal M8 bolt in length of 40mm for mounting. Mounting of the foot: Hold the foot upside down, so that the hexagonal hole show to to top. Insert the M8 bolt,…
This container is designed to fit even if the Squash Ball mod is installed on the printer. The Squash Ball mod can be found here: https://www.printables.com/de/model/447434-squash-ball-mk4mk3smk3s-vibration-damper-v40
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/k5QPTkLg09O Category: 3D Printing
i attach the .3df file for mofifying with your own dimentions Printed in PLA with Sidewinder x1 : Layer 0.2 infill 15% …
I made those cracks for stick in there some doble face tape. It should be printed with TPU
Hi, if you like the Design please leave a like. I had a Storage with Pipes in 30mm inner and 34mm outr Diameter where i needed to deal with uneven floor. In this construdtion you need to put in a 8mm M8 Hex Bolt and in the inner part a…
I added some feets, so the box can sit. I printed with Prusa Mini. I used PLA, 15% infill, NO supports.
The Classical 3DBenchy BUT With A Pair Of Feets
Baseplates to fit the Hula Feets on voron 2.4 Printers with the Z-Drive Motortensioner Mod. The Z-Drive Motortensioner Mod is located at Github here:…
Foots for the Keychron K1 keyboard with a built-in USB hub. Used parts: Board from ORICO USB Clip Hub 4 Ports Threaded heat inserts M3x4x5 Countersunk head screw M3x7 USB Type-C soldering adapter with screw mount Print Settings Printer…
A simple riser plate feets for Xbox series S so it can suck air from below easier improving cooling
Feets for the Flexlink track and it's paletts (old version)
Hey hier sind 2 Ständefüße für ein I:sy Cargo mit dem Ständerdurchmesser 22.4 und 22,45 jeh nach dem wie runtergerockt der lack schon ist! :) Hey, here are 2 kickstand feet for an I:sy Cargo with a stand diameter of 22.4 and 22.45,…
see FeeCad project file on GitHub: foot.FCStd
Screws for sealing threaded holes, sizes M8, M10, M12, M16. These screws seal threaded holes on the upper edge. This protects them from dirt, paint or similar substances, e.g. when painting workpieces, and also protects unused threaded…
My daughters received Hatchibabies toys for Christmas. They kept the lower half of the egg as a bed or chair but it wasn't stable since the base is rounded (it's an egg, kinda expected!), so I designed this small base to keep the eggs…
Spare feets for a Hawo grain mill. I put some felt stickers on all of them. Happ grinding. Ersatzfüße für eine Hawo Getriedemühle. Ich habe auf alle Teile Filz-Möbelgleiter geklebt. Frohes Schaffen.
Feets for monitor stand / desk shelf. 2 Seizes avaliable. Avaliable in 30mm (Long) and 26mm (Short) heights. To hold it in place, you can use a 4mm diameter wooden screw.
I mounted my lightbox topframe with these feets. The 4 mm hole could be used to bolt the tubes down, i didn't do that because the friction fit on regular PLA worked just fine.
Feets for the ABK Open Frame Case: https://www.etsy.com/de/listing/1247015223/voll-atx-computergehause-open-air
Riser feet for the Lelit MaraX v2 coffee machine. As the MaraX v2 lacks threaded inserts, the feet are mounted using a flexible TPU 95A expansion plug. An M4 nut is inserted into a slot inside the TPU plug, which then fits into the foot.…
The original table feet were too slippery, so I drew overshoes and printed them in TPU.
A small model for my Geneve XL. Designed for the original countersink screws that came with the stand. I wanted to replace the stand with small feet to have the projector a bit lower. I used the 30 mm version with the original power cord.…
Wir haben eine Tisch Erhöhung für unseren Esstisch gebraucht um unsere kalten Platten aufzustellen. Werde diese Platten nun weiterverwenden als Monitorerhöhung am Schreibtisch. Die Oberteile werden einfach nur in die Füsse mit eingesteckt…
Dieses Modell ist passend zum Lenovo Legion 7 15IMH. Es ermöglicht dem Notebook durch das abheben von der Tischplatte eine massiv bessere Belüftung vom Gerät. Ich empfehlen den Druck mit TPU da damit das Gerät auch nicht wegrutscht beim…
Screws for sealing threaded holes, sizes M8, M10, M12, M16. These screws seal threaded holes on the upper edge. This protects them from dirt, paint or similar substances, e.g. when painting workpieces, and also protects unused threaded…
