356 modeli
This is a ESPHome based Hichi/Volkszähler interface specifically for the Holley DTZ541 that has alignment pins instead of the more common round indent around the IR interface. UPDATE 2023-01-29 Previously mentioned issues with the…
A cover for the Sony Multi Interface Shoe that allows for a Lapel microphone to be clipped on and attached. Protects the digital pins by covering them. The cover does not touch the pins at all. Should work with all lapel microphones with…
NOTE: this interface was designed to suit the studioform BSB X1 foam interfaces/the original V1 studioform dream air interfaces (which were the same thing). If you want to use the newer v2 studioform interface they are notably larger and…
There are loads of Garmin interfaces out there, but (in my opinion) they all fail for one of two reasons: the intended print orientation is horizontal, thus mandating support structures that are difficult to remove and leave residual…
Plastic part of the Quest 2 facial interface. You can Glue in some foam padding or Velcro to have detachable padding. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 0.16 Infill: 25% Filament: Any…
The Pico 4 is better in almost anyway than the Quest, it is lighter, better balanced, and has a higher FOV out of the box than I have been able to get with any facial interface for the Quest. The only thing the Quest does better is…
This is a hot shoe cover optimized for the Multi-Interface Shoe that is being used on all Sony cameras. It should fit on any other camera brand as well though. I modeled it similar to the original that ships with the cameras but improved…
Hair clip/plugsuit head input for Rei Ayanami from Neon Genesis Evangelion, I based it on figurines of her. Shinji Ikari uses the same ones I believe. There's a second version which I sliced a curve of the bottom in case you want to wear…
EN: Unified box for 4.3 inch display and interface board for JK-BMS. It is possible to edit the pack number in Bambu studio (1, 2, 3, etc. or anything else) the file is attached below. Ready for AMS. Happy printing! :-) I added a model of…
It's better to use SG90's screws. Discover my miniatures, keychains and others models on my Printables page.
See https://www.amazon.com/gp/product/B08CHCG42N/ref=ppx_yo_dt_b_search_asin_image
Hair plug for Asuka from Neon Genesis Evangelion. I based it on figurines of Asuka and made two versions: one with a more rounded top and one with a bit more pointy top. I've included the Fusion360 file so feel free to alter the design or…
I accidentally uploaded a wrong STL for the button. Its now updated! I purchased a 18650 capacity tester from AliExpres
I remixed the mount to fit perfectly to the Steinberg UR22C - Audio Interface
Big Evangelion fan here, both of the original and the rebuild, and these have been on my list to make for a while despite others existing elsewhere. Hair Bands Please choose a hairband from the Cosplay Hairband System (CHS) page to…
This is my first attempt at making a STL file in Fusion 360 so please be kind, Thank you.
Features: New belt clip that allows for toolhead disassembly without taking belts off or having to re-tension after Tries to get toolhead as close to rail as possible for better center of gravity Featured in model: Dragon Burner Toolhead…
Le modèle original est déjà très bien, j'ai juste ajouté le nid d'abeille sur les faces pour l'esthétique et l'économie de matière. Merci au créateur pour sa création (Effectuer une symétrie de la partie droite pour la partie gauche du…
This is a replacement for the stock facial interface for the Quest 3 that works like the one on the Q-Pro. I use it with the Meta Quest Elite Strap, and I also use a chinstrap. For more info on the chinstrap see my chinstrap cup project.…
Test to dial in settings for support interface roof and floor density, thickness, z distance.
Protective box for Xiegu's CE-19 interface, used for the Xiegu G90 and X5105 HAM radios. Print either bottom or bottom ONLY AF-CON. The latter only has the Radio and AF-CON holes open, the other has all openings. The box is printed so…
Beta Testing Notice This model is currently in beta testing. I printed the manifold in Prusament Jet Black PLA. It had some stringing across the tube holes that required some cleanup with an X-Acto knife. I printed the Modified transport…
Rear segment of the Rocinante from Martin (part xxx_-_roci3) without the legs interfaces. The model is available for MK3S and for MMU (3 parts to insert together on prusa slicer)
Still somewhat WIP (has some light leak at the moment), but I'm using it as is for the moment. This does NOT add any space between your eyes and the lenses, other mods exists if you feel your eyes are too close. This transformed the…
The STP for Dream Air & Dream Air SE face interface — especially the surface area where it connects to the headset is useful for modding.
Mount for the Behringer UMC202HD USB audio interface (maybe works for other models, too). The front plates are hold in place by M4 melting inset nuts. Printed in Devil Design PETG on a Prusa Mini clone.
This is a mount for a Behringer U-Phoria UM2 audio interface. didn't like how it took up desk space and also how it would get dusty after a while so designed a mount so that it can sit under the desk. uses 4 tiny screws (guitar screws…
This is printable addon for Fury's Quest Pro style Meta quest 3 face cover V2 https://www.thingiverse.com/thing:6277086 Printed using colorfabb varioshore TPU, standard settings for MK4, but filled 8% for softer interface. This version is…
While trying out Sony hot shoe covers for my A6700, I wanted to test out making them out of some of the Proto Pasta Copperfill PLA that I had on hand, and then sanding it smooth to bring out as much of the copper shine as possible as an…
These Support Interfaces are used in conjunction with my 1/60th Scale Apollo Saturn V MLP skin set.
Press Like for encouragement. Comment for improvement. Adaptor Virpil/Thrustmaster base to VKB NXT grip and vice versa. It hasn't been tested since I do not own a VKB. Thanks to crash1983 for the VKB interface! Note: 3D-printed plastic…
These are fully 3D printable SP connect bike phone mount interfaces. The files are available as .step file so that you can use them in your designs. Provided are the old SPC style interface and the new SPC+ interface. I have printed both…
This modification allows WS8 implementation to SP-5. For nut, you should use nut adapter. https://github.com/MirageC79/Interfaces-for-WobbleX-integration/blob/main/Voron/Trident/WobbleX_TR8_Adapter%20Body.stl
Wham Bam Mutant V2 Interface Plates for Popular 3D Printers Designed to be used with the Wham Bam Mutant V2 Universal Tool Swapping System. UPDATE Aug 20th 2022: Added a MUTANT X carriage plate adapter for the Elegoo Neptune 2, 2S, and X.…
I've had this aging (but fully working) Aircon unit in the garage for a while, the interface for the hose split and was unable to source a replacement so I've finally got round to designing a replacement. I've yet to fully print this (20+…
Background As an active portable ham radio operator, I am always interested in evolving my gear to support a wide variety of ham radio activities. My primary rig for portable operations is the Yaesu FT-891 and with no internal soundcard…
A quick and useful adapter to connect the original prusa PTFE fitting to a 3rd part Mini Heatsink replacement. Print settings: 0.1 DETAIL resolution 100% infill Material: PLA, PETG - (printed mine with good PLA)
Make your own, simple and cheap neural interface. You can use it as an interface between your brain and computer or machine. Follow instructions at https://opentechlab.webnode.cz/eeg-neural-interface/ Print instructions Materiál PETG
Excuse the poor geometry, I went more for it working than for looks. To get the lens out of the goggles you need to unscrew these screws and essentially rip it apart (it shouldn't damage it) You might need to remove the fabric You can…
I have a fan that uses a Makita battery. One day, I wanted to power the fan directly with a DC power supply, without using the battery. This plate helps my fan stand stably. The model can also be used for other purposes, such as with a…
The Modular Wind Tunnel for STEM Education is distributed in the Printables Store and is therefore automatically licensed with a Standard Digital File license that, unfortunately, limits the community's ability to contribute to the…
This is a simple model used to test support interface material combinations. Set filament 1 as your main printing filament and filament 2 as your support interface filament. For example, if I set filament 1 as PETG and filament 2 as PLA,…
This is an improved case for the optical read/write head for energy meters (smart meters) developed by the "Volkszähler" project in Germany. In addition to the printed parts you'll need: a ring shaped neodymium magnet, outer diameter…
Big Evangelion fan here, both of the original and the rebuild, and these have been on my list to make for a while despite others existing elsewhere. Hair Bands Please choose a hairband from the Cosplay Hairband System (CHS) page to…
Summary Comfortably connect a drybox to a MMU inside of a 3D printer enclosure. Each PTFE tube can easily be identified by a number tag and can carry a color tag that can be taken from the tube end and be placed onto your MMU slot to…
Have you been frustrated because you bought a bunch of Cricutmaker pens that don't fit in your joy? Fear not! The interface is here! Simply print and go, you can use the screw to tighten looser pens like a Bic pen or colouring pencils, if…
Support interface of Stargate stand for X-303 design from Martin.
Features: New belt clip that allows for toolhead disassembly without taking belts off or having to re-tension after Tries to get toolhead as close to rail as possible for better center of gravity Featured in model: XOL Toolhead…
The ESP32-S3 is just hot glued to the tft for now. Printed in ABS. but can be printed in whatever you want. You can crazyglue the top button trim but I found that just the bolt from the encoder is enough to hold everything in place. If…
This interface is a connection between the hose of the Mistral SUP hose. To fill the big amount of air with a electrical pump. For the high pressure the hand pump is still needed but the electrical pump saves time. This part is made for a…
In order to be functional, additional parts are needed: 4x M4 button head screws 16 mm long, 4x M4 nylon lock nuts, 6x 6 mm dia x 3 mm thick magnets (found here:…
If you want to print smooth surfaces but have to use supports for your model then there is a simple trick to do so. Just use PETG as a support interface in case you got an automated multi material handler. In my case I use an BambuLab X1C…
I avoid using supports at all costs unless it's absolutely necessary, but dialing in the settings for your support interfaces makes using them a little less frustrating. I made this small model to test multiple different support…
The perfect bookshelf for your engineering textbooks…well, ok, maybe just for a couple of them :) The total load case for the design was 75 lbs, however, I have NOT verified the accuracy of the design tool, or ‘sanity check’ any of the…
This is a generic facial interface for the BSB. You need velcro tapes, 2mm(Diameter)*4mm magnets, and a facial interface with velcro backing(tested with AMVR's pico 4 facial interface).
The interface supports consist of the corner and side supports of the MLP that are attached to piers used to anchor the MLP. In addition to the original Apollo MLP piers, the shuttle added additional piers that attach to the underside of…
ITA: Tutti i file devono essere stampati due volte, tranne "MixerStand-3" che deve essere stampato in 4 copie. Per le parti laterali capovolgi il modello nello slicer in intrambi i lati e in modo da non aver bisogno di supporto. Consiglio…
I just edited the very good mod by John Doe to accomodate bigger 6x3 magnets (superglue suggested)
A local Farrier asked me to replicate the design of the 3DFarrier horseshoe interface, which allows horseshoes to be quick changed. Very interesting article about the inventor of this design:…
This is an interface plate for the Origami S Dripper to stop it's incessant wobbling with the Wooden plate. I'd advise printing in a food-safe high-temp filament since the outside of the brewer can get quite toasty during brewing and…
This is the track interface piece that goes with the Brio Lift and Load Warehouse. We lost this piece and the tower doesn't work without it, so I bought another whole set to model the piece. Brio does not offer a replacement part service.…
A simple merge of the two designs.
My take on a 3d printed case for the Glasgow Interface Explorer . I designed this case to fit the latest (at the time of writing, C3) revision of the Glasgow board as delivered by the crowdsourcing campaign. For the 3d printed parts I…
This is a snug fit for the Clarett/Clarett+ 2Pre (including its rubber feet) and the latches hold the interface firmly in place. So it's no problem to plug in/out an XLR cable with one hand. Yet, after disconnecting the cables on the…
Holder for Anker 313 Magsafe pucks featured in this amazon link (https://www.amazon.co.uk/gp/product/B099WRPVJK/ref=ox_sc_act_title_1?smid=AISREEIOH9TSP&psc=1) Which was a budget friendly alternative to the original Magsafe buck. I get…
The files include just modified versions of the base for Garmin in three variations: Basic, 90-degree angled, and Garmin Duplicator. The rest of the files are in the original model…
Printed in ASA 0,15mm layer. glue body and ESP mini together. YAML and ESP info can be found here : https://github.com/SysAdminDk/EspHome/tree/main/IR%20-%20Heating%20Meter%20Reader IR eye ( remove back cover to fit)…
These interface files are STEP file provided by the designers at Worker. This would have saved us a lot of time with our ‘Puffin’ mod. Redesign your own front ends!
Free up desk space by moving the chonky Clarett+ 4Pre under your desk 20% infill and some supports(that take a long time) should work in almost any material Category: Other The mount is tilted just over six degrees so plugs will clear…
I reccomend printing this at 100% infill in PETG for the best results. The bottom row of holes are made for 1/4-20" 3/16 socket cap screws. The VIU is best mounted with velcro, however there are included holes for the appropriate 8-32…
Custom usb-c interface to control PWM devices like PC-FANs or lights with the AC Infinity 69 Pro controller. Disclaimer: USE AT your own risk AND you might loose warranty on the product The case is designed to be used with Arctic P14 PWM…
This is a male interface adapter that can be attached to allow devices with without Garmin mounts to connect to a Garmin female connector. I designed it to attach to the underside of my Cannondale Synapse Integrated Cockpit stem (old…
part to attach a motor rc500 15440 to a Lego Technic
Works on UltraLite MK4 --but may be compatible with others This bracket allows my MOTU UltraLite MK4 audio interface to be mounted under a desk. Since the bracket may work with other MOTU interfaces like the MK3 or the UltraLite AVB. It…
This is the mechanical part of the optical PC interface connector for a Fluke Scopemeter. The original interfaces have a special mechanical connector and are very expensive. I couldn't find anyone who already had created this part or have…
Based on the original 3d model provided by Meta, found here: https://developers.meta.com/horizon/downloads/package/accessories-guidelines/ This expands the sides with accommodation for glasses frames. Definitely not that comfortable…
For breakaway/dissimilar support interface materials, you should use 2 layers of 100% support interface density (no fan). Have 0 height space between the interface and the supported layer. For same material support interface, you should…
Adapter zur Anbringung des Loxone Zählerinterface IR Air an eZB Zahler DD3
For my first robot project I want to use the URM37 ultrasonic distance sensor from dfrobot. So the first thing to do was to design a good housing for the sensor and make it attachable to a servo. Category: Robotics
First of all: this is a remake of the amazing: https://www.thingiverse.com/thing:4817279 I first published it here: https://www.thingiverse.com/thing:4846512 I made the following changes: the table now is bigger : 28 cm of diameter I used…
This is a collar that attaches to MSA respirators in the same manner as MSA filter cartridges. It may be useful in adapting other types of filters onto these respirators. I'll be using it with the HEPA filter cartridges that belong to my…
I liked bondematt's design with the vents, but also furryWallpaper's idea with the neodym magnets, so I enlarged the holes for 5x3 mm neodym magnets. Also, I enlarged the space in the middle to create more clearance for the head strap.…
(If you find any of my models for sale online (ebay, amazon, etc) it is not me, i do not sell prints; especially not at those insane prices. They are all listed as non-commercial works. I do not have a patreon or kofi or any donation…
This adds an M6 thread for a pneumatic coupler so a reverse Bowden can be fitted.
Needed a simple interface box for my pedalboard. I needed 2 inputs (1 each for an acoustic and an electric) plus a balanced output. Printed so that each of the faceplates sit into a groove in the shell and the lid. 3m inserts and screws…
I have an A1 and can only print 4 colours at a time. Added a pause after the white was completed to swap it for silver. If you can print more or do not want to change colours, please ensure you remove the pause in the slicer.
Gridfinity Interface plate for dashboard modules You need magnets to connect to a Gridfinity base plate . I used a 0.2mm layer height with a 0.4mm nozzle. no support needed Included is the f3d file
STL has moved to https://makerworld.com/en/models/109292 The STL is a refined version of the one in the photograph, it is strengthened and the interfacte strip is re-aligned for symmetry. I suggest printing with block interface pins at…
Big Evangelion fan here, both of the original and the rebuild, and these have been on my list to make for a while despite others existing elsewhere. Hair Bands Please choose a hairband from the Cosplay Hairband System (CHS) page to…
This is a case for the EMS with an ESP32 AZ-Delivery NodeMCU and board from BBQ Kees. This a amazing project can control your boiler, heatpumps with an EMS bus. The case is quick and dirtry, so you may need some hot glue to fix the ESP…
Wahoo adapter for the Z1 Cycplus mount, pretty inexpensive and easy to find in AliExpress or similar webpages. I also increased the height so the Wahoo doesn't touch the mount when mounting it. You will need M3 heated inserts for…
Summary These interface blocks can be used as in insert in your printed object making a secure connection between it and the HSW grid. Where i already used these blocks: HSW sliding box collection by DennisP | Download free STL model |…
These are fully 3D printable Wahoo bike computer interfaces for all possible print orientations. Even the flexible tabs holding the Wahoo in place are fully printable with print orientation taken into account. They can be fully integrated…
A few months ago, I modified Zeeflyboy’s excellent face gasket design to feature an open bottom and added external mounting points, eliminating the need for the original Pimax metal bracket. With use, I found that the gasket could sag or…
Its an under table mount for 2x2 audio Interface specifically used for IKEA UTESPELARE table, It can be also used on all generic tables as well.
This was a request by some of my patrons Printable surface is likely reduced a bit to 200(X)x225(Y) Has be tested and working! This replaces the " X CARRIAGE_TOOLHEAD/ENG-XC1_b.stl " piece Everything else on the original Ender NG Post…
I absolutely LOVE—and can't recommend highly enough—PeakDesign's case for my iPhone 14 Pro Max (another great, beautifully engineered PeakDesign product…), and I've also been a fan of DJI's Osmo family of gimbals since they first…
These are fully 3D printable Garmin bike computer interfaces for all possible print orientations. Even the flexible tabs holding the Garmin in place are fully printable with print orientation taken into account. They can be fully…
The new cube farm we moved into at work after the building was remodeled doesn't really support using push-pins to hang things on the walls. There are 2 versions, one that takes an M4 hex nut, and one sized for a RuthEx M4 threaded insert…
This is an old project that was never meant for sharing. It's still salvageable for enthusiasts, but not easy or simple to make. In fact, you will have to figure out a few things yourself if you want to recreate the ReFOVeR. It will…
