211 modeli
To hold my scope probes so they don't clutter my workspace I made a clip that fits to the left-hand side of my Hantek DSO2D15 oscilloscope. Can be used for other scopes too, it fits the Hantek's PP150B probe and the P6100 probes commonly…
Many thanks for Yanev for making such a grat box! Hovewer, after trying to customize it to fit FNIRSI DSO152, it occured to me, that minimal height of the bottom and the lid are 15mm each, a little to much for that small oscilloscope. But…
Feet and rubber pad inserts, universal across the Tektronix TDS500/600/700 oscilloscope family and possibly other Tek equipment from related lines. This is a near-identical copy of the original with a few changes to take FDM printing into…
Replacement knob for broken one on Rigol oscilloscope. 6mm shaft. Printed in white filament PM. Print instructions: Layer height 0,1mm, no supports.
One-handed differential probe for two-channel oscilloscope with math function. With dual acupunture-needle handle holes for alternative or additional pins pointing to same probe tips center location. With adjustment screw, M3 hex nuts and…
O'scope came with 4 color bands, none of which matched the dark-blue of channel 4.
Replacements for the screw covers on the handle of TEK314 storage oscilloscopes.
Introduction This oscilloscope is sold either assembled or as a kit. Whatever the case, you might want to enclose it in a box. Original acrylic boxes were sold but I gave them a pass when they were available, and now I just printed my own…
A simple stand for the DS212 from miniware (see e. g. https://e-design.com.cn/en/Mini-Oscilloscope-DS212-PG9226721 ) which simplifies the readout of the graph. Materials I've printed with: PLA and PVB I printed it a while ago, so I don't…
Reproduction fidèle de l'emblème du LOSC, adaptée pour une Impression multicolore à couches variables (sans MMU) . Paramètres utilisés pour la fabrication du logo mural (gcode fourni) Périmètres 2 Couches solides Dessus : 5 / Dessous : 4…
oscilloscope probe holder Double sided tape is required for fix.
This is a remix with added inserts of the excellent parametric rugged box that can hold a ZT-703S oscilloscope/multimeter (or a ZT-702S since they share the same dimensions) and some of its accessories. The two grids have to be glued in…
Krabička pro osciloskop FSCOPE-500K a DSO-500K https://oscilloscope.fhdm.xyz/
I have a 4 channel Oscilloscope and this helps me keep them out of the way. I print multiples of them and mount them side by side so I can hang multiple probes, hats, etc…
I wanted a box to store the DS213 pocket oscilloscope that had the same size & shape as my TS101's box. I also made a stand, this can fit under the probe tips, it prints in one piece mostly, but there are two small “cubes” that can be…
I have uploaded Revision 2. The first model is the yellow one in the photographs. Revision 2 is the red one in the photographs. It has additional structures to place the oscilloscope probe tools.
Not much to say else. Just print it no supports needed in any filament type you like. Choose between text and no text version. OpenSCAD File included as ususal. Have fun!
The oscilloscope is well made, but the screen is not well protected, being surface mounted on top of the unit. Bigger buttons are also nicer to press. You can fit a thin screen protector under the bezel for additional protection (I used…
Enough room to hold two pairs of oscilloscope probes or larger test leads / multimeter leads. The two smaller holes hold smaller clips or test leads. Turned out better than I was expecting. Have been looking for a solution other than a…
A travel cover for Rigol DHO8xx series of oscilloscopes. Designed-in support allow printing on any printer with a build volume ≥ 250mm x 250mm x 210mm, i.e. MK3S, Bambu X1C, P1S, etc. Many thanks to Slant 3D for the support tip that…
An enclosure for the DSO138 oscilloscope with room for a 9V battery. Print Settings Printer: TronXY X5S Rafts: No Supports: Yes Resolution: 0.25 Infill: 15% Filament: Generic PLA Any Category: Electronics
Dieser Leuchtturm ist eines der Wahrzeichen von Bremerhaven. Er steht auf dem Willy-Der Leuchtturm Bremerhaven (auch Alter Leuchtturm, Großer Leuchtturm, Simon-Loschen-Leuchtturm oder Loschenturm) steht als Bremerhaven Oberfeuer am Neuen…
This is a holder for oscilloscope probes. I have them screwed to a shelf above my workplace. Fusion360 design file included for easy remixing.
This custom-designed probe holder is made specifically for my Rigol DHO804 oscilloscope. It should work with any DHO800 series scope and possibly DHO900 series (need to verify). It provides a secure and convenient storage solution for…
oscilloscope probe clip holder
This is a case to cover the sides and back of the Zeeweii DSO154Pro portable oscilloscope. It's meant to be pressure-fit, so you may need to adjust dimensions by 0.1 or 0.2mm depending on your printer's tolerances. There's also a small…
These probe holders are deisgned to hold oscilloscope probes in place for debugging and testing. Use with 1/4oz adhesive wheel weights to help keep them stable along with 9mm OD rubber bumpers. The source design files for SOLIDWORKS and…
Takes a raspberry pi pico on a breadboard (the standard small size ones, 35x45x10mm) in the back, standard 6mm banana-plugs in the front, and a phone up to 13 mm thick.
Several models of oscilloscope probe holders. Version for gluing or screwing and the height of the holder is 12mm. The holder is designed for probes with a diameter of 10mm. ---------------------------- Několik modelů držáků…
"Lille" Filament changes to achieve the desired result. Standard coaster size and 7mm thick. Printed with .2mm layers. Can be scaled up for a plaque, I would keep Z at 7mm even for a plaque Red till 6mm Blue 6.2 - 6.4 White 6.6 - end
Case for Osciloscope with support for Mobile or Tablet
Front screen cover for the FNIRSI 1013D Oscilloscope to protect the touch screen while in your backpack or tool bag. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Infill: 15 Filament: PolyMaker PLA Notes:…
This is a VESA mount adapter for the Rigol MSO5000 series Oscilloscope. Mounting the scope above your work surface increases flexibility, frees up space, and puts the scope at eye-level. Tool-less mounting of the oscilloscope,…
This case attaches with slightly longer bolts in the rear of the oscilloscope. Keeps all pcb layers, just added to rear and provides side covering. Much easier to use and hold now.
Printed in standard PLA with low layer height (0.8mm height took 1 hour) and 55% infill. Tight fit. Print two so they match!
Just a standard 1165 x 1165 x 150mm Australian pallet. Import into your favorite slicer and then reduce the model size. 5% works perfectly if you are printing a pallet for your Bunnings/Hammerbarn forklift model. Printed pretty well on a…
Eine Schaufel für das Katzenklo. Mit stützen und 0,2layer
I have a Rigol DHO914 Oscilloscope and I find the fan noise annoying so I designed a rear mounted adapter to mount a larger fan, using the VESA mount screws on the rear of the scope. I used a Noctua slim (15mm) 92mm fan NF-A9x14 PWM but…
Helping hands oscilloscope probes REGOL PVP3150 Probe Two AA batteries are used as weights
A set of 3D models of knobs and buttons for the Tektronix TDS210 oscilloscope . Also may be suitable for other Tektronix oscilloscope models. The set includes: Tektronix knob mini – small knob; Tektronix knob – large knob; Tektronix…
Picked up a DSO152 Oscilloscope and it came in a box; here's a nice way to keep it. This one is large enough to hold the “deluxe” version with the nicer probe, so if you skipped that, you could probably shrink this down quite a bit. You…
The adaptation of previous script. The ends can now be made stronger and you can rotate the object so when printed on a side you get much more strength to hold the tools. Instructions print attach use enjoy :) (after printing this type of…
A remix of mbmelectronic's model that can be fixed to a wall with screws through the holes
I updated the back of the Scope stand to include a 9V battery. The front part comes from https://www.thingiverse.com/thing:959009 Category: Electronics
This versatile 3D printed model is designed to securely hold your oscilloscope or multimeter probes, offering a practical solution for wire management and easy accessibility. The multimeter probe holder boasts a universal design, ensuring…
I cracked a knob on my old Tek TDS220 scope so I made this. It is a tight fit. It might work on yours too. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.1 Infill: 11 Category: Electronics
For all your messy o-scope storage needs! Internal dimensions of the box are 125 x 200 x 80mm (box = 50, lid = 30). For assembly, you'll need M3 screws. Four M3x30mm (hinges and latches) and two M3x35 (latch catch/handle) Three lids are…
Gridfinity box for Fnirsi DSO-TC2/TC3 Mini Digital Oscilloscope 2 Storage for USB-C Cable / 3x test Hook / crocodile clip 1 Storage for BNC adapter Gridfinity 3x3 size
I have created a holder for four measuring tips. These can be attached to the VESA screw points of the oscilloscope. The negative of the probes is adapted for Rigol DHO probes. It is suitable for VESA 100x100 mm You need 2x M4 threaded…
I like the original design, but it was too wide for my compact size oscilloscope and I had not enough desk space for it. So I came up with this version. It has a footprint of 324x200mm and is intended to be used with smaller oscilloscopes…
This stand is a pair of parts (right and left) that snap into place on the bottom of the DHO800/900 oscilloscope to raise it about 4 inches and tip it back to make it easier to view. No screws or spacers needed, it clips firmly into place…
This inserts should be use with Rugged Box Parametric V2 model made by @Whity You will need the original packaging to use it as an oscilloscope holder in the box. Rugged Box Parametric V2 parameters: InnerBoxDepth 185 mm InnerBoxWidth…
Remix of Case for Osciloscope Scoppy from VladimirWaas_694872 This case accommodates the DSO/FSCOPE-500K boards from FHDM. The boards are based on the Raspberry Pi Pico and function as front-end for the Scoppy Oscilloscope firmware, which…
This probe tray is designed to store the probes of the Rigol 1054Z, Just because I didn't like the bags provided. The trays are stackable and comes with a lit for the one on the top. Category: Tool Holders & Boxes
I bought my Tektronix 50 MHz scope used a few years back. It came missing the control knob for trigger level. I would frequently swap the "holdoff" knob, located directly below it, until one day, one of the two prongs seating the knob…
Finally a proper way of storing my hantek oscilloscope with its probes. No support needed :) Category: Electronics
Dies ist ein kleiner Humidor, der in eine Zigarelloschachtel passt. Gefüllt wird der Humidor mit Befeuchterkristallen aus Acrylpolymere, diese findet ihr bei den bekannten Onlinehändlern. Neue Version! Dank der Inspiration von hpolack die…
Oscilloscope probe to wire adapter For Rigol probes (PVP2150, DS1054Z) This allows for a soldered probe connection with minimized lead inductance. Heavily inspired by https://www.thingiverse.com/thing:4935122 Oscilloscope Probe to Wire…
Oscilloscope probe holder V1 This oscilloscope probe holder is great for keeping all laboratory probes organised. More than one type of mounting is available: Mounting via M4 countersunk head screw U-profile bar mounting Hook version: A…
I made a snap-in mount for our 4 probe rigol 1074Z It works very well. OpenSCAD source is also available here. Enjoy :* Category: Electronics
This is a remix of @uSD_cardlord_2322350's inserts for the SQ10 probes, so that you can also store the similar oscilloscope probes in a rugged box. The remix is a bit quick and dirty in terms of details, as I didn't have much time. But…
[Simple Attenuator Box] with 5 stage, for BNC connectors very useful for Osciloscope, Fox Hunting, Audio Tweaking/Freaking, Ham Radio… i plan on using Dymo tape on the face to mark the attenuation values. Material: 2X BNC connector 5X set…
I designed this tray to nicely store my Hameg Oscilloscope Probes. It will likely work with many makes of probes or you can modify it with the included fusion 360 file. It is stackable. You can experiment with different printer settings…
I made a Gridfinity-based holder for the popular and cheap Zoji oscilloscope. A few other accessories are supplied in the 3MF and FCStd files as well. With magnets on both the holder and the base, the device stays firmly in place and is…
Replacement foot for Rigol DS1000Z series oscilloscopes (ds1054z, ds1074z, ds1104z). The angles, dimensions and the flappy action are similar enough to the original feet, so you can just replace one of them. I also used a 2mm steel axle…
******* PCB for USB A plug temporarily removed due to an error ******* This is an enclosure for a 3 port USB extension hub to fit to a RIGOL DHO800/900 series Oscilloscope allowing three devices to be used with the single USB port whilst…
This is a simple replacement stand for the Zoyi/Zotec ZT-703S. It may work with the ZT-702 as well but I don't have one to test with. I print it standing vertically with the top hinge side on the heatbed but you may find another…
Tektronix 2230 oscilloscope front cover Snap on front cover for Tektronix 2230 oscilloscope. Printed in two halves plus clips and connector for glue. Based on an ebay listing for an authentic front cover, this should fit models: 2213,…
This is a case for the Sainsmart DSO138 Digital Storage Oscilloscope board. All switches are accessible. The range slider switches have extenders on the left. Function push buttons on the right are molded into the case. Probe and power…
The adapter helps improve airflow and device cooling under prolonged use or high ambient temperature. Designed to be installed without modifying the oscilloscope — it uses existing screw points and aligns with the stock vent grid. Fan…
Simple UNI-T osciloscope holder for Ikea skadis. https://x.com/3Dpetr_kolos
Locks the probe in the 10x position saving the headache of having to constantly check.
This is a simple remix of the original that uses M3 threaded inserts instead of M4. You will need to download the “mountingplate” model from the original. The CAD file I used can be found on OnShape at this link .
This will mount a Zoyi ZT-702S or Xeast XE-702S (same product just different branding) to Multiboard using Multiconnect. You will need to print the Multiconnect connectors here:…
No Support…just print it :-) Two alternatives… use what you like.
These are probe holders for Rigol RM-DS1000Z rack kit. 4x M4x12 or M4x14 countersunk screws are needed for mounting. Designed for RP2200 probes.
Intended for resin printers. Barbie scale oscilloscope with sine wave on the screen. Category: Toy & Game Accessories
print two of each. Includes recess for the power cord.
Very small stand for DS212, DS02 or similar size oscilloscope or some other device. Part dimensions are 35 x 5 x 10 mm so it easy fits in any box or bag you use to carry osciloscope around. Although You may use single stand it is more…
Rack mount for the Rigol MSO1074Z oscilloscope - should fit other models from 1000Z series too like DS1xxx, MSO1xxx (check your model's dimensions). Official rack mount kit is quite expensive (around 250€) so I made this one. It also…
Sometimes, when using an oscilloscope, it is desirable to be able to get the probe attached to the PCB. This may be to lower the loop inductance of the ground lead or just because the probe is difficult to hold in place. This adapter…
Protect you (toy) oscilloscope! Has cutouts for power, ventilation, and all buttons. Printing Instructions Printed from PLA with high infill and no supports. Consider printing the buttons and switches separately with brims.
Oscilloscope BNC Connector cover Protect Oscilloscope BNC connectors from rusting/environmental factors
The DSO150 is a great small form factor oscilloscope marketed as being portable. This would be great except for one thing. Most versions are sold with no battery and require you to use an external 9V. In my experience your average 9V…
Clip version needs to be printed on back, with support material for the wire rack. May need to resize clip depending on the thickness of whatever you're clipping it to. Currently sized for a 12mm or ½" thick shelf. Other versions can be…
Remix of 4 channel oscilloscope probe holder. I needed to hold 1x 9mm probe as well as 12mm probes, so I made the last one smaller. I also made a flat base so you can sandwich between the oscilloscope and the shelf. Category: Electronics
OpenSCAD implementation of parametric tip cover for scope probes. This is an accessory usually bundled with probes, but they're tiny and prone to be lost and, above all and in my experience, they have a section with larger diameter than…
Simple parametric object that can be used as a probe holder. Parameters to the module are number of probes to hold (4 probes by default) height of the holder (20mm by default) Instructions Print screw or glue use Category: Other
No special printing options. This case is a kind of slide on cover case without snapping. So if you print it it could be snug fit togehter or need glue at some points. I have put the freecad file online, so you can remix the model for…
better pictures coming later. this is a simple box that has 3 BNC in the back and a single ON/ON double switch in the front. very useful for all kinds of application! from antenna testing to plugging multiple things onto your…
Stand for comfortable use if the DIY Scope shell. Includes hole for 9V battery. There are 2 versions: In DSO-ScopeStand2.stl you push the connector of the 9V battery through the hole. If your connector is too big for the hole then use…
Loved the original model, but the latches were too tall for the box. It looked like others had this issue, as well. Rather than having everyone have to solve this on their own, I just made one for the masses. I shortened them up a little.…
This model is pretty big. The french cleat part is a separate body that needs to be screwed into the main body, so it's at least two parts. But since those parts are very long, I included both versions, one being a single body, and one…
This system helps keep the Rigol Oscilloscope in place on the shelf when you either touch buttons or attach/detach the oscilloscope probes You need to print: A: 2xRigol frame B: 2xFrame_stopper C: 1xArm_NEW D: 1xBack suspender Screews…
A stand for the DSO138 oscilloscope with the (standard?) acrylic case. Heavy enough that it does not slide around the worktop as you connect it up ;-). I also incorporated some storage for probes etc. All the ports and connections are…
This design allows you to get stuff (oscilloscope) off your bench and on your Skadis board where it belongs. This has hex holes to help save some filament. It may also fit other similar models as well. Make sure to check the measurements…
4.3U 19 inch rack front panel mount for Rigol DHO800/DHO900 oscilloscopes These panel mounts require the DAP 2U MP-1 bracket. This bracket must be cut in half, with the two halves moved 4.3U apart. Print the two halves of the front panel…
Got tired of accidently pressing the AUTO button and decided to do something about it.
Porte clé du logo original du club de foot de Lille, le LOSC.
