326 modeli
My Spirit XS shaft outboard works great but sometime sucks in air from the surface leading to ventilation/cavitation and power loss, especially in reverse. This plate fixes that. Should fit both the Spirit 1.0 and 1.0 plus as they have…
Inner part for Aearator M24.
I wanted to make a train set based on the Railway Series story "Tobys Vintage Train" for those who have read the story it only consists of Toby the tram engine, Henrietta, and Victoria. but on Wilbert Awdrys Farquar's layout, there is a…
Ein einfacher Sicherungsring für 80iger Weck-Gläser um zu verhindern das der Glasdeckel herunterfallen kann. A simple safety ring for 80 cm Weck jars to prevent the jar lid from falling off.
This was made in like 15 minutes in photoshop then exported to tinkercad. I've tested it with Frontline Foam's and Spectre's M79 barrel adapters with Monkee mods threaded jet blaster barrels, and both work fine. I intentionally made the…
Einfacher Organizer für eine 1kg Packung Mehl + Mehlsieb + 1 Päckchen Backpulver + 1 Päckchen Vanillezucker.
Print 1:1 - PLA - module with designed interface of our other module (pin and hole) so keep the ration as indicated to fit into other modules or change ration to all of them equally. (More models on our Tinkercad, gradually we will upload…
My Bambu X1C vibrates quite a lot which means sometimes the bucket is being pushed away. When that happens I find filament everywhere on the table. That's the reason why I made this Remix. If you already printed a bucket without cutouts…
This is 3D printable model of the Excelsior Class NCC-1701-B Enterprise from the Star Trek. It is a kit. The different colored parts are separated for easier printing. Pieces of the necelles need to be separated into separate model in the…
The LSI 9300-16i HBA is a wonderful choice for DIY NAS enthusiasts, but outside of data center with frigid climate control and numerous fans pushing air over its heatsink, it tends to get warm. This shroud clips around the LSI 9300-16i's…
This is an older design. Please consider also checking out this one created by @ briancmoses : https://www.printables.com/model/1046107-lsi-9300-16i-hba-cooling-fan-shroud This HBA runs pretty hot and I wanted to mount a fan to it instead…
Just a callsign model I put together for my brother. Make all the changes you want to make it your own.
🇫🇮 Tervetuloa Helsinkiin! Welcome to Finland! This model was designed by Dany Sánchez with optimizations by Jukka Seppänen @kijaidesign . The idea of MiniWorld3D came to creator Dany Sánchez after a Finnish friend who asked if 3D printing…
I am try to create new another water jet boat propulsion for RC models. Actual version used on by boat is "v12" It is complete open source (only for non-commercial use, another license on request) Do not hesitate to add comments about…
Fan shroud to mount an Noctua NF-A4x10 to an LSI 9300-8i HBA. Design idea copied from @BlackHornet_355398 's fan shroud here: https://www.printables.com/model/377809-lsi-9300-16i-noctua-nf-a9x14-fan-shroud I have a LSI 9300-8i, but this…
Fan shroud to mount an Noctua NF-A4x10 to an LSI 9400-16i HBA. Design idea copied from @BlackHornet_355398 's fan shroud here: https://www.printables.com/model/377809-lsi-9300-16i-noctua-nf-a9x14-fan-shroud I have a LSI 9400-16i, but this…
I designed a PCI full height bracket for my LSI 9211-8i HBA card since it didn't come with one. I used two M3x8 screws that can cut their own threads, but you can also use M3 nuts to secure them (I did). The two holes are spaces 54mm…
LSI 9305-16i or LSI 9305-24i fan shroud. This is a remixed design from barichardson with most overhangs removed to be more easily printed. Snaps onto the heat sink without the use of screws. Four STL files for both the 16i and 24i with…
UPDATES: 19/09/2026 Updates pushers, now slimmer to help them stop striking the dart lever. 11/09/2026 New Dart Guides, 2 options created, one with a dart detector switch, another without. Gives way more reliable readings compared to the…
PC Case: I was building an inexpensive PC with a very tight budget. I sourced parts from Marketplace, eBay, etc which meant I ended up with some oddball hardware, but I still wanted it to be compact. So I made a case around an ATX board…
This is a remix of https://www.thingiverse.com/thing:3646996 I have modified it to use a 40x20mm fan, instead of the 40x10 fan from the original. Tested with a Noctua NF-A4x20 FLX fan. For best results, print on it's side with…
A screen printing scoop designed based on some I have seen on the market. I wanted to print my own so I designed one. One side is round and one side is sharp. There is also a ridge on each side for easy grip. Print the middle piece at…
hiho, alle 18V ProCore Akku-Halter Modelle die ich gefunden hatte, haben leider gar nicht gepasst oder nur unausreichend. Ich habe dieses von Grund auf neu konstruiert und iterativ angepasst. Print settings: PETG 30% infill 3-4 Layers /…
This is a tapered car cup‑holder adapter designed for slim energy‑drink cans such as Alani Nu, Celsius, Red Bull 12oz, Monster Ultra slim, and other narrow cans in the 57–58 mm diameter range. Most car cupholders are sized for standard…
Diseño de un portabolsa para llevar colgado del pretal del animal o en la correa, personalizado con el nombre.
Flat and round pocket whistle / Silbato de bolsillo plano y redondo
This is a ham radio callsign display you can have on your desk that looks cool!
I took this excellent model and remix the hinges (bigger with a plug to make it mobile). I've change the interior covers (to participate in a printing challenge), in one side I added a Sun clock, and in the other side a message Witten…
Update 26 October 2023: back parts with Voron BOM parts added as well. Update 23 October 2023: I've added the back parts as well for all sizes to complete the looks. Schurter D12 inlet for now, Voron BOM options soon. To keep all the…
Hellsing ARMS 454 Casull nerf pistol. Not for kids, this thing hits hard. 9 bearing BCAR ensures accuracy. 8 round magazine. Hardware kits for this model can be found here:…
Full size birdshead style grip for NAA revolver chambered in 22s. Crazy tiny little wheel gun, this makes it possible to hold onto it. :) Screw holes are sized for M3 screws and nuts, print flat side down with copious support. Inletting…
Kelsier's dagger from Mistborn! This is designed based on the one that was available in fortnite. It can fit a 300x300 bed printer. Mirror the pieces to get the complete dagger. One side will take roughly 108g at 17.5 hours at .28MM layer…
4 new variants : #1 lsi-fan-bracket-v4-Finished Bracket No holes in the pillars v2.stl - Only holes in the pillars removed, for a Noctua fan #2 lsi-fan-bracket-v4-Finished Bracket Noctua Raised pillar v1.stl - For a Noctua fan, holes in…
Custom two-color keychain with your amateur radio call sign (or anything really). These are also handy as tags for your ham radio gear. Includes a 1" black key ring. Printed in PETG at 0.2mm
I created this model to help cool my LSI 9300-16i SAS HBA, which runs very hot when not in a server chassis with lots of static pressure. I printed this in PETG, but you can probably get away with PLA+ if you have enough airflow. Printed…
https://www.thingiverse.com/thing:1675987
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Simplemente para poner el monedero, monedas, llaves, etc. lo que solemos llevar en el bolsillo al llegar a casa. PLA Altura de capa: 0.2 Relleno: 10 velocidad: 60
Hummingbird art to display on your wall Scale as you need and glue to attach it to your wall. Enjoy
A PCB that lets you use aftermarket quick releases to provide power to your diy wheel. You will need the spring pins and the JST connector, they can be found on aliexpress, search terms: “JST XH 2 Pin 90 Degree SMD” (2.54 mm Pitch)…
Feyenoord logo to display on your wall. Scale as you need and glue to attach it to your wall. Enjoy
A tool used in screen printing to evenly apply a layer of photosensitive emulsion onto a screen mesh. Model can be resized to fit any screen (as long as your printer can fit it)
Any suggestion is welcomed! Feel free to join my Facebook group to let me know what you want: https://www.facebook.com/groups/1115757609295068 Custom display base are also available from $5! Contact me to discuss what you want! If you…
Habe zwei STLs eingestellt. Einmal das normale Logo und einmal mit dem Schriftzug "Pokalsieger 2018". Habe jede Ebene 3mm abgesetzt, falls man das ganze nach unten skalieren will oder muss - Außendurchmesser bei 100% ist 200mm. Somit kann…
Most amateurs put up a callsign display in their shack. I thought it was a bit boring so I designed something more fun! Its almost turning into a amateur radio playset ;) The base is a simple enclosure which you can modify to add your…
se puede imprimir completamente hueco si quieres ahorrar filamento, tiene unos agujeritos abajo para que pueda salir el agua en caso de que se moje. It can be printed completely hollow if you want to save filament, it has some holes at…
- Replacement for the broken propulsion holder from the mothership of the Starfares of Catan Boardgame (old version). - This is the original STL-File that comes from Kosmos. They provided in the expansion pack for 5-6 Player two of the…
A fullsize panel mod for the v0.2 with 100mm Tophat. I wanted to enclose my Voron as much as i can for printing ABS/ASA. Since i don’t use the tophat i choose to go fullsize panels with some mods already found online and a few adjustments…
The Base model includes holes sized for M2 threaded heat-set inserts. The insert cavities are designed so that the inserts are installed from the top of the case. I recommend, for inserts at this size, putting a long M2 screw through the…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Hellsing ARMS Jackal nerf pistol. Not for kids, this thing hits hard. 9 bearing BCAR ensures accuracy. 8 round magazine. Hardware kits for this model can be found here:…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Bench mountable funnel for directing brass output from Rollsizer into bucket using 2.5" flex hose (avail at RangePanda). I needed a rectangular funnel that I could attach to my bench that would catch brass ejected from my Rollsizer into a…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
A Spaceship model as inspired by Excelsior, the spaceship as seen in the Fantastic Four Marvel movie. It is printed in parts, and should be glued using the attachment key pieces as a guide. Superglue (cyanoacrylate) works well with PLA;…
A nice pirate logo for your wall, man cave or kids room :-) Scale as you need and glue to attach it to your wall. Enjoy
Funny Sign - "If a woman is upset HOLD HER and tell her how beautiful she is. If she starts to growl, retreat and throw chocolate at her", multi colour print, printed in ZIRO PLA Twinkling Black and Sunlu Matte white PLA. For more funny…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Our 3D printable Tintin rocket is a fantastic model rocket for those looking for an adventure. The model comes with STL files for 3D printing, making it easy to create your own customized rocket. To add to the excitement, the rocket is…
Steps to install whole setup into the Lenovo M720Q Minipc: Print this model with a sturdy material like PETG Take off side/top cover of minipc (screw on the back and slide towards front IO) Take out 2.5" drive holder by pressing down the…
Mounts a Delta BFB04512HHA-DV52 45x10mm blower fan to the heatsink of an LSI SAS9300-8e card. Will work with other BFB04512 variants, but the BFB04512HHA-DV52 is the one you want if you care about PWM control. Requires two M3x10 hex…
I used some 0.5mm clear PET plastic for the windows, it is optional. MMU is not required.
This 40mm PWM fan mount is for 9211-8i cards that use a 30x54x10mm heatsink, such as the Fujitsu D2607 variant. I might even work with the LSI 9260-8i (IBM M5015 variant). Fans are screwed in on the backside so you can add thicker 40mm…
Pin de bloqueo: para evitar que se abra o cierre accidentalmente Diseño delgado para que entre fácilmente en el bolsillo Dos modelos: con orificio para anilla y sin orificio para uso libre Se puede imprimir en PLA y PETG sin problemas…
Yes that's slow-motion, I posted the full speed version in the makes section.
A cute house in shape of a cute Kawai cat. The house is assembled via hex pins and dual compund resin (dont try to use superglue, you will have a bad time... ask me how I know) The whole thing comes in 3 profiles: The Base The Walls The…
Adapter that secures the LM18-LSI sensor lens, for the PMW3610 sensor, when used with the original BastardKB Charybdis trackball assembly.
Just a little lid to snap onto the skinny can drinks (like Red Bull and Celsius, etc.). I printed this in a mix of PETG (blue) and TPU (yellow) so the TPU would give a little. Solid PETG or PLA would work too but be a tighter fit. Tabs…
This thing was made with Tinkercad.
My 9200-8e was getting a little hot, and I couldn't find any fan adapter's for its tiny heatsink. I decided to make my own to fit these 40mm fans I already had, available here from Amazon: MakerFocus 4pcs 3D Printer Fan 12V, 40mm 12 Volt…
Bram Stoker's Dracula - Abraham Van Helsing (Anthony Hopkins) - 1992 3D printable model.
I printed this on its side with only necessary support. I'm not sure which is best for it. The fit is excellent. Be very careful with the clip on the heatsink as the heatsink is not rigidly mounted and the chip on the PCB has no metal…
Realizado en Pla la duración de la impresión en una mk3s+ es de 2 hora 30 minutos aproximadamente Realizado con una boquilla de 0. 4 mm para que vibre hay que poner un guante de látex o de goma fuerte sujeto con cinta adhesiva o una…
Low profile bracket for LSI 9212-4i4e SAS HBA adapted from https://www.printables.com/model/244218-pci-low-profile-brac
Remix of the 20mm 16i fan shroud to fit a 9400-16i May fit others but I've only tested With that. Made it slightly wider to clip over the PCB rather then under the heat sink. Included a .dwg that contains 1 object all merged together and…
Diese Figur ist ca im Massstab 1:24 und ideal für Resin Druck
Hammer Films Characters - Professor Van Helsing - Horror of Dracula - 1958 3D printable model.
A magazine adapter for feednecks, to use TIPX magazines! No supports needed. Uses 2 3mm x 10mm compression springs. I used these (amazon affiliate link, I earn from qualifying purchases): https://amzn.to/3MAKW7J Also needs a 3mmx35mm…
Hammer Films Characters - Van Helsing - The Brides of Dracula - 1960 3D printable model.
I wanted to add prints showing the valence shell electron pair repulsion (VSEPR) theory for the most common geometries to my undergraduate general and inorganic chemistry course. My intention was that this would help students understand…
Experimental! Update 03.05.24 Added drum screen variant 2: Variant 2 has much wider bars inside the drum than variant 1. The idea with the wider bars is that fewer longer-chip particles fall through the sieve than with variant 1 - since…
The model includes cavities for M2 threaded heat-set inserts instead of through holes and includes M2 through holes for tenting puck compatibility. The insert cavities are designed so that the inserts can be installed from the back of the…
24/1/2024: Alternate selector wheel added 1/12/2023: LowerFront is a depreciated version with a slot for rev trigger, have updated it with the current version which deletes it 28/11/2023: Forgot to upload the mag guide file, have uploaded…
Ham radio callsign stand which you can change callsign in slicer
LSI 9300-8i Fujitsu model remix of original. Below is link for onshape if you need to make more edits. Need supports as per the original.…
This 3D printed heart senses when it's touched and begins pulsing in response. Full build guide can be found at https://learn.adafruit.com/3d-printed-heart-capacitive-touch Print instructions Category: Biology Summary This 3D printed…
3D Printing Tips for Your Tulsi Gabbard Figurine ✅ Recommended Settings: Layer Height: 0.1 - 0.2mm (To capture the fine details of her professional outfit and gentle features). Infill: 15-20% (Enough to keep her sturdy but not weigh her…
This is a caddy rail for 3.5" harddrives on a Fujitsu Celsius M740 Power. It has been remixed from bbountyhunterr's Fujitsu Celsius Etna D3128 SSD Caddy Rail. I have designed two variants, one requiring HDD mounting screws and one…
Dobrý den, Vítejte na mém profilu, plném modelů a miniatur :-) Mám pro vás vymezeni hlavně pro Airsoft sniper pušku. Tohle je konkretně tvořeno na model M24 Sniper. Pasuje pekne i funguje. Nevyzaduje zadny odpor, silu. Obsahuje 2 modely :…
It's a very tight fit, and the SAS card is slightly unaligned but it fits, and it works \_(ツ)_/
This garden light can be used as a floor, wall, or hanging light. It is approximately 40 cm high, making it a full-size fixture. It is prepared for an E27 socket. Please use only LED bulbs (otherwise, excessive heat generation is…
SOPORTE DE MÓVIL V1 DE BOLSILLO Mas fácil de montar, con menos piezas y más rápido de imprimir.
One of the front plastic feet of my household stairs, 5 steps, of “Excelsior” brand (I think these are manufactured by Altrex), had disappeared, and the other one seemed to be on the way out, too. I modeled and printed two replacement…
Remix of a LSI 9211 PCI bracket to be stiffer and printable without support
This is a PCIe Bracket for mounting an LSI SAS 9300-8e in a Full Height PCIe slot. I found it worked really well printing it with the little notch required for the SAS connector facing up an using supports under the bracket and inside of…
Blue Elsie - Pink Panther _ Wall Art
Bu model, geleneksel bir Türk nefesli çalgısı olan dilsiz kavalın 3D baskıya uygun halidir. Model, iki parça olarak tasarlanmıştır ve baskıdan sonra birleştirmeniz tavsiye edilir. Birleştirme yerindeki çubuklar hizalamayı kolaylaştırmak…
Este modelo esta compuesto por una base, una tapa para guardar el Tangram y por los 7 Tans que son: 1 Romboide 1 Cuadrado 5 Triángulos (2 grandes, uno mediano y dos pequeños) Las dimensiones del conjunto cerrado serian de 84mm X 84mm X…
