155 modeli
The stock battery mount on the Happymodel Mobula 8 likes to break after some not-so-soft landings and snaps where the two crossbars connect to the side of the battery holder. This model replaces the crossbars and hooks into the sides of…
Wydruk około 0,08 €–0,10 € nettoWstępna wycena jednego wariantu
As tough as the Mobula 8 is, it won't probably survive throwing it into a backpack to take it with you. This case allows you to do exactly that, while also protecting your whoop from some rain or mud. Fits analog or Walksnial 1s Mobula 8…
Wydruk około 10,19 €–12,45 € nettoWstępna wycena dla PETGMateriał u źródła: PET
***This Frame is fairly fragile. It will not survive moderate impacts*** I wanted to experiment with 3D Printed frames after snapping one of the plastic pins on my Mobula 8 Frame. This is my first attempt (well, first attempt that…
25.5х25.5 Canopy Walksnail 1S lite kit camera (mobula, meteor etc) Weight = 1.7g Angle = 30
In case somebody needs a 3d model of mob7 frame for making custom canopy or whatever. The model is accurate to the production frame except symmetrical motor arms and straight duct profile.
I designed this new canopy for Mobula 6 to solve some problems: It has support for copper antenna on the rear. Upgrade recommended for yours. Support for a small 9mm buzzer. As it is very small, a buzzer is useful to locate it if it falls…
This is an improved version of my Mobula6 canopy Pinch Camera adapter. This one uses the camera-holding design from RAB's awesome folded canopy, but I wanted to have the protection, light weight and instant angle adjustability of the…
printable without supports. may need to re-drill the circuit board mounting screw holes, as they are only 1mm diameter. The STP file contains separate sub objects which are not joined to each other. you will need to perform a Boolean…
Replacement frame for mobula8. This frame is not bulletproof, but should take decent hits without braking instantly. I've made few modifications to stiffen up the frame. Weight is around 17g (original 11g), so sligthly heavier than…
Modula 8 camera canopy - with and without rumcamthumb pro mount. supported camera angles upto 30deg. Let me know if you need one for more camera rotatiion. Support can be a little tricky to remove but hang in there.
Mobula8 Battery Holder The original Mob8's frame has a very tight fit for the higher capacity 2S batteries, often requiring force to clear some parts of the frame and the micro USB jack. I designed this battery holder mod for the Mobula8…
A carrying case for the Mobula 8 drone. I wanted a carrying case that didn't take up too much space, but was sturdy and secure enough that I wouldn't have to worry about having my drone inside, with foam to absorb any shocks. I used the…
The mobula 8 is a good drone, but its battery attachment system is far too limiting. To increase the choice of drone batteries that can be used with the mobula 8, we need to make a few adaptations. I've designed a very simple and flexible…
dji 04 lite canopy for mobula 8
Strongly inspired by the very effective design of ngn33r: https://www.thingiverse.com/thing:4859251 other cam sizes & angles can be updated in the provided F360 files.
A small adapter clip to screw a Caddx Ant Lite into a Mobula6/7/8 canopy using M2x4 screws and M2x3 heat inserts. M2x3 heat inserts from cnckitchen Be careful while melting the inserts in as the plastic walls are very thin. I added a…
Better looking AND more practical box for your tinywhoop. You might need to cut corners on the foam insert for proper fit. You will need: 4x M3x34 nut (can be longer) 4x M3 nylon bolt Optional parts: TPU part for better seal. ( not…
Happymodel Mobula7 1s tinywhoop open prop conversion frame inspired by the flywoo firefly nano baby frame. Weighs about a 4g, 1g lighter than the happymodel ducted frame. Very strong, pretty much will never break as this frame with the…
tpu 50%infill - weight with 04lite = 21g. 0.2mm layer height organic supports should fit original 04 lite camera faceplate & and axis flying 14mm camera housing. install your camera first and run a small zip tie through the spaces at the…
1mm wall thickness Can be printed in PLA or PETG with some overhang artifacts, that noone will ever see 😇 TPU might work as well, but won't be as protective for the lens. Suitable for Foxeer Toothless2 nano (Starlight) camera (14 mm wide,…
The batteries I use don't fit the stock holder so I cut the horizontal tabs out, put this tray in (with a bit of sticky battery pad) and looped some velcro through the vertical tabs. This has been through some big crashes and battery…
This is a O4 canopy for Mobula 8. Recommended printing with TPU 68D filament (I printed with TPU for AMS). I recommend setting 100% infill and using tree supports. When printed with PLA and subjected to a crash, it breaks (tested). Allows…
This is a hard case I designed for my new Mobula 8 Tiny Whoop Drone. It uses the foam out of the box the drone came in. The latch holds the case closed and is adjustable. I printed this in abs but should be fine in pretty much any…
tested and works great! I just added a higher angle version….
I remixed a battery holder for the tinywhoop drone Mobula 7 1S from Happymodel. With my model you can carry a 500mAh Tattu 1S and the model will be below 2g. I printed with 0.24mm layer height using Red PLA+ from CC3D
Remix of Krhom's first O4 mount. No supports needed, printed in TPU 95A, works with the OEM self-tapping screws, maintains some camera tilt options. You do need to trim the canopy arms around the USB-C and the Digital port so they're not…
Canopy para tiny whoop Mobula 6 en filamento flexible TPU en diferentes diseños con orejas, tiburón y simple. Especificaciones: Para imprimir de manera adecuada el filamento flexible TPU, se recomienda usar una impresora 3D de extrusor…
Habe ein paar Teile gemacht, um für meinen Mobula 8 ein Walksnail Avtar mini 1s zu adaptieren. Der Mobula kam mit dem Frame für das DJI O3 light, ich wollte das aber mit dem Mini 1s von Walksnail ausrüsten. Nach einem ersten Versuch mit…
A GoPro like mount for the Happymodel Mobula8. It can be used to mount a light camera like the Runcam Thumb or Thumb Pro to the Mobula8 Print Settings Printer Brand: ELEGOO Printer: ELEGOO NEPTUNE 3 Pro Supports: Yes Resolution: 0.20 mm…
Remix for woodprop's mobula 7 case from thingyverse (https://tinyurl.com/2pue85ds), used 5x3mm magnets and filament piece for hinge. used velcro to attach batteries to top of the case.
1mm wall thickness It is recommended to print in resin but should also work fine in FDM. Suitable for Happymodel Ant camera (14 mm wide). Mount hole size: 25.5mm*25.5mm
This frame can be used with Mobula 7 parts. Canopy and batterystrap needs to printed in flex filement. Print Settings Rafts: No Supports: No Resolution: .2 Infill: 100 Filament: does'nt matter PLA Category: R/C Vehicles
Frustrated with the fragile and difficult-to-source stock canopy for the BetaFPV Air65? The original canopy, while lightweight, breaks easily and offers limited, cumbersome camera adjustment. This design allows you to upgrade to a more…
I have made a case for the mobula7 1S with compartments for my charger (VIFLY Whoopstor), USB charger and a short cable. Also there is space for 7 1s batteries. I can also make one without the charger compartment, just ask!
This is a GPS mount for the Happymodel Mobula 8 quad. (Beitian BE-122 gps module) You also need a M3x10 bolt to install it on the mobula frame. Models available: Total weight “NO VENT” (25% infill, 2 walls, 0.2 layer height) = 5g Total…
I was annoyed as I kept hitting the ground with the bottom of the drone. I made these small, light and efficient legs which work with original screws. My quad now weighs 37g with the battery and with the stock battery (250mah) I have the…
To fix the gears to the drone you need three m2x5mm or m2x8mm screws. Print tips: -print both parts and glue them together -print laying on the side -use support touching only build plate
This is a remix of Airmaxx23 model for the spiked canopy - https://www.thingiverse.com/thing:3385065 For the mobula 7 I decreased the internal width to fit the camera and also made sure the screws for securing the camera had enough depth…
Got a lightly used Mobula7 1s ELRS version with 8 BetaFPV 450mah batteries BT2.0 connector for a deal. Flew it about 8 times using the battery lead in tensions (connector at the front) to keep the battery from coming out but a high speed…
I remixed the moblite canopy to use a front screw so it would be compatible with a full size flight controller. The angle is about 30 degrees using the last hole. Category: R/C Vehicles
Caja diseñada a medida para dron Mobula 6 Tiny Whoop con tapa que cierra a presión gracias a mecanismo de clicks. Custom designed box for the Mobula 6 Tiny Whoop drone with a lid that closes under pressure thanks to a click mechanism.…
A 3D-printed IKEA Skadis mount for the Mobula 6 FPV drone would be a compact and functional holder designed to securely store and display the small quadcopter on the popular Skadis pegboard. The mount should feature a custom-fit cradle or…
A canopy to mount O4 lite on Mobula 8 frame. Print with hare 70 D (or harder) TPU, 15% infill, 3 wall loops all the way. Airunit is mounted hanging downwards, with a set of M2 bolts without nuts - screwing directly into the TPU. With two…
Got bored from duck taping the original frame after every hit to a wall. This is durable, but you should order more props ;-) New PID tune is required, in general, lower the P-gain for 10-15%. Print instructions This is 105mm frame for…
Mobula6 Drone Transport. I needed something to put my Mobula6 in instead of a cardboard box. No supports.
I broke the HappyModel EOS2 canopy that I purchased, the screws ripped right out of screw holes, also the camera angle would change every time someone sneezed in my house so I figured it was time to design a new one. I did design this so…
Version V2 available Mobula 8 new GPS mount ________________________________________________________________________________________________________________ This is a simple GPS holder for the Happymodel Mobula 8 quad. (Beitian BE-122 gps…
Bought some batteries that were mislabeled in the specs and they were too big to fit into the regular tray. Customer service gave no response so I figured I would try to make it work. The batteries fit snugly into clip (tighter than the…
Anyone who has purchased these batteries will know they don't fit and require some surgery on the frame but there was no quick solution that would let you do flips without the battery being yeeted out. I gave this a decent test run with…
Update New design - print with supports :-) Simple stand for Mobula 6 with slots for batteries and USB charger from original package. Battery hole dimension (Length x Width x Depth): 12,5 x 6,5 x 8 mm. Note: I miscalculated when designing…
A canopy to mount O4 lite on Mobula 8 frame. Print with hare 70 D (or harder) TPU, 15% infill, 3 wall loops all the way. Airunit is mounted hanging downwards, with a set of M2 bolts / nuts. With two fresh BebtaFPV's 550mAh batteries, I…
This is an easy printable mount support for Hawkeye thumb 4k camera. Must be in TPU material. For the installation you'll need 2xM2 screws, the one's in the pictures are perfect. Its suitable for all canopy Mobula style. Enjoy! Print…
A case for 75mm tiny whoops like the mobula 7. Print instructions Category: Robotics
This is a remix for the walksnail version of the mobula 8. https://makerworld.com/en/models/689978#profileId-618749
I designed this thing to fly 1s300 packs on a Happymodel Mobula 7 frame. It has a good friction fit on the battery, similar to a mobula6/meteor65. It snaps in place so you can keep it in several packs in a row, and pop it out easily when…
Petg and PAHT CF are my two favorite options
This is a TPU protector for the O3 camera on Happymodel Mobula8.
Simple cover for USB 1S charger. There are also holes for two LEDs and a switch. It also fit in stand, which you can download here: https://www.printables.com/cs/model/238194-mobula-6-stand Other FPV stuff: Alien 5" GoPro mount Alien 5"…
This is a buzzer mount for Tiny Whoop AIOs (28.5x28.5mm) designed to tidy up the buzzer installation under the canopy. The design has been optimized to be printed with TPU and to be very light. Print Settings Printer Brand: Creality…
This is conversion frame mobula 8 to 3 inch toothpick
I broke the HappyModel EOS2 canopy that I purchased, the screws ripped right out of screw holes, also the camera angle would change every time someone sneezed in my house so I figured it was time to design a new one. I did design this so…
A mount designed to hold the Mobula7 (and other Mobula models) on the IKEA Skadis pegboard. It uses the universal hook system.
this is perfect mobula 8 antena cover
Improved previous concept, made it lighter and made a lot of small improvements. It is meant to replace the mobula7 frame, but can probably replace most crazybees of this size. It is intentionally multi-part to enable two different kind…
The Walksnail Moonlight Mount is a -designed holder for attaching the Walksnail Moonlight Kit camera to the Mobula 8 O3 drone. This mount ensures a secure fit and optimal camera placement for smooth, stable FPV footage during flights. ✅…
Simple case for the Mobula 7 drone. The case holds the drone, 4 batteries and spare propellers. The lid and clip are simply snapped together, no gluing is required.
Based on a Viking helmet model originally shared on Autodesk’s community platform, licensed under CC BY-NC-SA. Modified and adapted as a Tiny Whoop canopy. All credit to the original designer and Autodesk. Not for commercial use.
Frame Mobula6 remixed model My Mobula6 65mm frame copy. I've not original frame and not tested model (waiting parts for my first TinyWhoop). If you want print frame give feedback please so that i could change. (I'm just learning)…
Same dimensions as the one on the mobula6 Category: R/C Vehicles
I liked the original design a lot, but I prefered to have a case where I can put all my things in... So I created that remix. It will have enough space to fit a small BetaFPV Lipo Checker... of course you can use it for sth. else too,…
Cut the original battery holder parts off so that you have two parallel and flush rails which the battery holder clips into. print in TPU
Frame modified for mobula6 hd and its runcam split 3 lite board. Category: R/C Vehicles
I love to make useful 3D Desgins, and i love Coffee: Buy me a Coffee: https://www.buymeacoffee.com/phitscho Or Twint me something over 078 713 68 61 THANKS! Batteryholder for the Happymodel Mobula 6 It is designed to hold 1S 300mah 75C…
Super easy quick print. Rounded side is the one you insert a battery from. No supports for either version. The ultra light is still super sturdy. Go for that one first. You can clip off the two existing battery clips if you want to…
Mobula8 Frame is soo damnn easy to break, its better to switch to the more durable Meteor85 frame. The Original EX1103 motor screw pattern is different from what betafpv uses on the meteor85 so its necessary to drill the fitting holes for…
-Note this still is work in progress- A case for 2 mobula 7 frame drones with a storage cutout for a Vifly Whoop V2 1s battery charger. It also has storage for 6 1s batteries in the lid. The hingess use a peice of 1.75mm filament as the…
Uses Phoenix-Prints' design: https://makerworld.com/en/models/938312#profileId-903531 Needs a lot of supports, organic are not too annoying to remove. Version on pictures is 30 degrees. UPD: I've been using it almost daily for months now…
STL found on Happymodel's website for Mobula 6 Freestyle HD Zero. I figured this might be useful for other builds too! Will also be uploading a remix of it in a 90 degree angle version I hacked together.
Remixed the mobula 7 canopy to fit my caddx ND filter onto the Turtle 2 - snug fit for the lens, so it holds the lens (which was a bit loose for me) perfect in place. Also protects all wires perfectly. On the picture you see the 1/2…
This is a storage and travel case for a Mobula6 tiny whoop, but any 65mm tiny whoop should fit. Pictured is the case holding a 2024 Happymodel Mobula6 HDZero ECO. I designed the case to fit the original foam that the quadcopter was…
Upon request I made a 2s lipo holder to fit the version 1 and 2 Mobula7 frame as they come designed for 1s batteries. Designed to be printed out of TPU. I printed at 0.15mm layer height, don't need support (looks like it does but prints…
Spacers for Happymodel Mobula7 FPV drone. In the model I got, it seems like the flight controller can move up and down way to far (up to 3mm). If it moves up or is pushed up (i.e. when plugging in USB), the FC then touches the…
A case for 75mm tiny whoops like the mobula 7. Category: Robotics
This adapter is used to mount the LiHv 450 mAh battery (I used these ones ) on the Mobula 6 Freestyle HD . Design to be printed using PLA or any stiff non-flexible filament (DON'T use TPU). Simply flex the original battery compartment on…
Quick base I drew for the Mobula 7 HD, though I think it should fit the Mobula 7 as well (as long as they have the same frame). It has 2 different positions, one in an angle and another one flat. The connector fits really snug with the…
Mobula 7 Battery Shim for when using a battery that's too thin like the WeBleedFPV folded 450mAH batteries or 300mAH batteries Print flat on the bed with supports (see pics). 100% infill Category: R/C Vehicles
Description This is a box for carrying the mobigital7 (mobula7 HD with vista naked). I set it up for the size of the mobigital7 with vista naked and frame mobula7 V3 with stock battery holder. You'll find the files in STL and STEP if you…
The "Mobula 7 Mount for Skadis Peg Board" is a 3D print file that allows you to securely attach your Mobula 7 drone to a Skadis peg board. The mount is designed with precision and durability in mind, ensuring a snug fit and stable support…
Just a simple addon to Mobula 7. No need for rubber bands. UPGRADE: Added spare wire holder. Category: R/C Vehicles
Heavily inspired by something I've found on thingiverse, which I can't anymore, so no attribution. (OG author, shout if you see this!) I tend to use a rubber band over the battery for extra secure fit. Print in TPU.
My friend crashed his Mobual 8 drone that had been factory fitted with the DJI 03 Air Unit. When he brought it to me for repair I found that the “factory” build had allowed the Air Unit to Flight Controller wires to move into the path of…
Fits 8 batteries, charger and spare parts
The quard is such a tight fit that you dont need a lid while you can easely pull the quard out again. If you want a lid, there's a 3mm hole and a triangle to help the lid stay in place. I havent designed a lid since i dont need it, but if…
TPU filament 1x M2 x 20mm Screw 1x M2 Nut The camera housing can be printed without support. The side where the lens is, has to be flat on the print Bed. After printing, you need to cut it with scissors. See the picture for reference. To…
Printed in PET-G this weights about 2g The 5.8Ghz antenna can be wedged in between the camera and the leading edge of the mount RunCam Night Eagle 3 at AliExpress: https://a.aliexpress.com/_EHhsPGd
Do you want a 2s 65mm "whoop"? I made a 2s 300-350mah battery holder to fit a 65mm frame, you need to cut away the old 1s holder. I did not turn the battery on it's side as it just starts to hang too low at that point. It works with…
My Camera screws came loose while flying so the washers went missing and then I lost one of the washers to the VTX board while I was swapping it out with a AXII Micro. Then I remembered I bought this 3D printer for some reason. So i…
