Liczymy pasujące modele…
Needs 2x countersunk Screw for Rigmount is designed for M8 2x M6x30 socket head screw & 2x M6 nut for mounting the light. the design allows for about 30degree of tilt in each direction
Changed to fit tp-link UH720 with charging ports on the side
You need 4x M3 Thread inserts, 4x m3 screws and 2x m5x50 Screw with nut. Print as orientated with supports for max strength. The toleranzes are very tight for mimimun wiggle. Maybe you have to use some grease You could also extend the…
Holds Racing gloves on a profile rig. For 40mm alu profiles and M8 Screw 3 versions: 1. with a rib for easy mounting on a vertical extrusion 2. with a rib for easy mounting on a horizontal extrusion 3. with clean backside
Should work with Moza too as they use the same QR but I can't test as I don't have Moza gear.
Made it heavier and bulkier and modified the orginal to be suitable for T-slot 4040 and 4080 used for most simrigs. the longer ones are real nice to cover up the cable completely print them all standing up (I used petg)
Flexible cable management for xx80 profiles. 200mm, 100mm, and 50mm for varied run lengths. Mostly intended for simpits but anything that uses xx80 profile and has cables can benefit. Saw a few other models for different profile sizes…
V3 UPDATE 11/12/24: Added reinforcement across the whole lip. ------------------------------------------------------------------------------------------- V2 UPDATE 25/10/24: Due to excessive clatter on the 8020 profile, I've added a…
I made one simple box for my Stream Deck MK2 to add it as a buttonbox on my sim rig. 4 pieces of M3x20 is needed for attaching the top to the bottom, selftapping holes in the top. I used the mounting from…
Its designed to be placed over a 4040 or 8040 extrusion and bolted on with 2 M8 screws. Feel free to ask any questions if theres something unclear.
This is a cable clip for a 4080 simrig to hold the larger cable sleeve. It clips onto the rig and stays put. Very small and fast to print so you can print several to help you guide the cable sleeve around your rig.
Here are my changes to the original models: Streamdeck_Mk2_Top: was remixed that a Stream Deck Mk2 fits in there Streamdeck_Base_Open_Bottom: was remixed that holes for USB-cable are at the bottom closer to the mounting holes…
I used a little support on the inside edges. Nothing major. Common M6/M8 hardware used to assemble. One could add some felt or velcro bits to soften the surroundings but mine doesn't rattle as-is.
simple remix of DaMaDo's mouse tray. 200 x 100mm so its narrow enough to sit inside the sim rig (useful if your available space is limited). I wanted something smaller and will be using with a trackball mouse so only really needs enough…
Ihr benötigt: 2x bzw. 4x M6x15mm -20mm Schrauben und Muttern 1x M4x20mm und Mutter 2x M8 Schrauben + Nutensteine für die Montage am Rig
A holder for Pimax Crystal controller that snug nicely so it doesn't move even for motion rig.
This is a simrig holder for the famous Nobsound NS-01G PRO Mini Bluetooth 5.0 Digital Power Amplifier. This Amp is quite commonly used für bass shakers. Link to the amplifier: https://amzn.to/4ucmMGd * Reccomended settings 0.16mm layer…
Upgrade your sim racing setup with this sturdy and practical phone holder, specially designed for 4040 and 8040 aluminum profiles (such as those used in a Sim Rig). Perfect for keeping your smartphone within reach to follow telemetry, lap…
A remix from the playseat version. Quick and dirty made because I couldn't lay it down anywhere near it where I could I could reach it. Modify it to make it better if you want. Print Settings Printer: CR6SE Rafts: No Supports: Yes…
needed to mount the usb hub to the profiles of my simulator it's a snug fit and doesn't jiggle around. uses M5 to secure
Designed for Fanatec wheels. Using my CSL Elite wheelbase as a guide. This suits both P1 and McLaren V2 wheels. I cannot guarantee this will be suitable for other Fanatec wheels as I don't own any other wheels, but I believe they will…
Inspired by RamjetX design https://www.thingiverse.com/thing:3077632 I made a bass shaker using the Mini Bass shaker pucks by Dayton for my Aluminium 8020 SimRig by www.swedishrigdesigns.com. In the stl files it's included also one design…
you need https://www.printables.com/de/model/721004-aluprofil-40-x-40-30deg-angewinkelt-winkel or equal profile to mount it to your rig
This is a simple headphone holder with M8 holes for my simrig
Designed based on the Fanatec QR2 Compability to QR2 pro or light not tested
Mountingbrackets for mounting Sabrent 4-Port USB-Hubs to aluminiumprofiles (Simrig etc.) Also he power supply can be used. Hole is for M8-screws.
Simple yet effective way to mount HOSAS to a 4040 aluminum extrusion sim rig. Printed with 8 walls and 5 top and bottom layers it's super strong and has no flex at all. It has holes for Thrustmaster T16000M Dual Stick and VKB Gladiator…
PLA 0.20 3 perimeters 50% infill Mount with M8 bolts in your simracing rig.
I wanted a clean cable management setup on my aluminium extrusion rig so I created some as the ones I found did not fit my displayport cable who were somewhat thicker than the power cable. One plate contains 4 clips, you can copy and past…
A simple swiveling support to install the keyboard to my Swedish Rig Design SimRig. The table it’s a mdf board 480x220x5mm You will need a 100mm screw and bolt and two large washers to be inserted between the supports. Category: Automotive
RSEAT P1 SimRig / Sinuslive Bass Pump III Holder Note my other models for RSEAT P1! You will need the following per holder / speaker: 6 x M4 4x6 embedded screw nut 3 x M4 x 12mm screw for the speaker 3 x M4 x 16+ mm screw for Part A and…
Wind Simulator Shroud to fit 120mm fans driven by SimHub with an Arduino Uno and Adafruit Motor shield. Print Settings Printer: Vertex 8403 Rafts: Doesn't Matter Supports: Doesn't Matter Infill: 20 Filament: Luxorpart 1,75 PLA Category: DIY
Hello everyone! I have created this simple mobile mount with a few aspects that I found interesting: Countersinking the screws to attach to the frame profile. Two screws for better fastening and to prevent the assembly from moving. A…
Passt auf 40 x 40 Aluprofil Ggf. mit Mauspad oder Oberfläche bekleben.
Added T-nut, for easy installation on a simrig aluminium 8040/8080/4040 frame.
A Mount for the Bigscreen Beyond 2 for 4040 extrusions. Requires 2 M8 screws. The original creator provided only an STL file. So the attached f3d file is pretty plain.
USB extension mounting bracket for aluminum profile cockpit to connect the steering wheels via USB.
Made a small change to the original model, brought the holes a bit inwards and made the middle connect with a dovetail to save 4 screws and nuts in total. Printed in Creality PETg with 15% Grid infill and 3 wall loops for a bit added…
A simple, strong universal hanging bracket designed to keep your sim racing setup clean and organized. Perfect for: Headphones / headsets VR controllers VR cables Anything that needs a solid hanging point This bracket is built to print…
Da ich keinen passenden Halter für mein Sim Rig gefunden habe, habe ich versucht einen selbst zu konstruieren mit Tinkercad. Im 2ten Versuch hat es dann auch Funktioniert und der Hub sitzt Bombenfest. Fakten: Drucker: Elegoo Neptune 4…
BACKGROUND Had no place to put keyboard, so designed a holder that slides into v-slot. Works just fine. Tested and adjusted for Omega V-slot profiles, but as profiles are standardized, it should fit any V-slot. CONTENT Design consists of…
An adjustable phone holder in 3 variants. Here the specs to all version: Small: 100 mm high High: 130mm high Both, the large and the small, have 4 100mm wide and 1mm deep indents for rubber feet to keep them from sliding. The phone holder…
Flexible cable management for RSeat P1 Simrig, respectively for any 50mm (round) pipes / tubes. Suitable for up to 5 cables with a maximum diameter of 8mm, normal power cables, USB cables definitely work. Note my other models for RSEAT…
For best results, use low rebound squash balls (aka super slow balls) If you want dampening + no-slip , then do not print the bottom part (you have to use the split to object function anyway) Bottom part is only if you want it to be…
Da ich keine Lust hatte 10€ für ein Monitor Mount zu bezahlen und mein Monitor so schnell wie Möglich an mein SimRig dran haben wollte, habe ich mir selbst eins erstellt mit maßen eines richtigen Mount, den man Online kaufen kann. Hier…
I made a mount for my brothers racing simulator triple-screen setup, for the external monitor PSU's of his ASUS ROG 32" screens. The PSU's are dimension 76*29,5mm (max) each. Mounts to your T-slot using M8 (max) screws and T-nuts. Print…
Since i didnt have a mouseholder on my simrig i just printed one! Easy assembly, no glue or screw needed for the table, you can also print the holders for the simrig, but the you will need threaded heat inserts and screws to mount it onto…
Cable Guide for moving seats designed for next level racing GTSeat Add-on it will work with any 40mm profile
RSEAT P1 SimRig Endcaps Foot Protector Note my other models for RSEAT P1! I printed the parts with: 0.2mm layer heights (Bambu Lab X1 Standard Profile@BBL X1C) 3 / 3 top and bottom layers 3 walls and 15% infill printed with regular PLA…
PLA 0.20 2 perimeters 30% infill Mount with M8 or M6 bolts in your simracing rig.
Printed using Bambu TPU for AMS (Hard TPU) using standard settings. If you put tabs up, and the large circle on the print bed, that will minimize support required. Uses M8 hardware into a 1.5" spacing aluminum extrusion rig. Contact me if…
Summary A remix form the nicely designed Logitech Webcam mount. This one is made for the C910 / C920 which you can tighten with a screw with a M6 bolt directly in the simrig. It's adjustable in height so it's usable for different monitor…
Made this to more easily move my stationary flight simrig around when needed using workbench castors. This is for an 880lb workbench castor from amazon: https://www.amazon.com/dp/B08FDFJXK5?ref=ppx_yo2ov_dt_b_fed_asin_title This uses a…
Bottom Mount Plate for several different Simrigs Typical Fanatec Holepattern which will suit all Wheelbases with Holes on the Bottom. Many different adjustment possibilities and super solid, no flex at all. The profiles used are standard…
Alternatives Gehäuse für https://www.printables.com/de/model/681518-led-licht-ambilight-drehzahlmesser inklusive Aufnahme für Aluminiumprofil Befestigung mit M6 an Aluprofil + 4x Magnet 10x2mm
I created an insert for my sim rig to hold an LED rope light to mount underneath. This channel is for an RSEAT sim rig, however you may be able to modify it or use it as an example to create one for your rig. The rope light I purchased to…
For mounting quest 3 controllers to an aluminium simrig, needs 4x 8mm bolts / t slot nuts
allen key holder for Next level racing simrigs with 40mm profile 6, 6 ,5 , 4 , 2.5 mm
Nachbau von der Original Abdeckung zum SR1 /Simrig.se → Preis Leistung 100%
Quick Release https://www.aliexpress.us/item/3256806823650864.html GX12-4L https://www.aliexpress.us/item/3256802442302567.html Bolts/nuts to suit your rig plus M3 6mm round head for the connector plates Epoxy glue It's been a while since…
I needed a bottle holder for bigger bottles which could also fit up to M8 Screws, as my rig primarily uses M8. Additionally it has a little notch on the bottom to prevent twisting and secure from twisting. Inside Diameter is 90mm…
Halterung am Simrig in zwei Teilen für den RSHTECH USB Hub 3.1 Gen2 mit 7 Ports Schrauben sind M6
Designed with the next level racing chair in mind. This "table" mounts to the slots on the chair mount with M6 bolt and nut so you have a space to have access to your mouse in order to make whatever changes needed by way of mouse.
WEC Hypercar decorative plate. NO BOLTS NEEDED FOR INSTALLATION TO 4080 RIGS (EASY INSTALLATION PRINT) 2 Print profiles one with rear hooks (easy installation) that allows it to be installed in 4080 rigs without bolts and nuts one with…
Custom designed 8020 simrig mounts for the Edifer g2000 speakers. They angle the speakers in 20 deg, and up 10 deg while securely fastening the speakers to the rig. You will need 4 (2 per side) M3 20 Screws and nuts to clamp the mount…
Holder for a 140mm Fan for my Simrig, i can also make a 120mm version if its needed for someone.
Recommended print settings Print on its side, because that significantly reduces the time it takes to print, and also cuts down on cost. Infill: No less than 20%, Gyroid highly encouraged Rafts: None Brim: None Supports: Yes Material:…
Soundbar Mount for 4040 / 8040 Extrusion This shelf mount lets you attach a soundbar to your sim rig or any other piece of 4040 / 8040 aluminum extrusion. All you need are velcro straps to secure the soundbar to the shelf. Dimensions File…
This is an USB hub mount for, in this instance, a Nedis USB 2.0 or 3.0 hub. Altough these are pretty universally produced. Just make sure to dubble check the dimensions of your hub before printing. The mount securely attaches the hub on…
Cable guide for managing 10 cables of 6 mm on a sim racing motion rig. It guides the power and encoder cables from the drives to the servo motors and keeps them neatly side by side. The top carries a chequered flag. The model is made for…
Inverted version of my chequered flag cable guide, for managing 10 cables of 6 mm on a sim racing motion rig. It guides the power and encoder cables from the drives to the servo motors and keeps them neatly side by side. The chequered…
I wanted my shifter to be in the same position as my car so that it feels more natural to drive with - especially since I am using a VR headset, so I created this stand. If you print this on a printer that has a smaller size than an…
This is a cable clip for a 4080 simrig to hold the larger cable sleeve. It clips onto the rig and stays put. Very small and fast to print so you can print several to help you guide the cable sleeve around your rig.
Its designed to be placed over a 4040 or 8040 extrusion and bolted on with 2 M8 screws. Feel free to ask any questions if theres something unclear.
Some of these mods don't need to be downloaded with the details in description. Its a collection of what I've got to work and found beneficial. A collection of various mods and updates to a MOZA R9 Simrig with EX Wheel, SRP Pedals and…
I created this bracket to mount my monitor to my simulator. 10 Series 1 Inch x 3 Inch T-Slotted Aluminum Extrusion. used T-slot M5 hardware. Yes, I can do other profiles.
For mounting quest 3 controllers to an aluminium simrig, needs 4x 8mm bolts / t slot nuts
air sim for racing sim works with Simracing Button Box [porsche 911 gt3 replica] by FoldingBlade (NOT YET PRINTED OR TESTED PRINT AT OWN RISK!!!) this model is subject to change and be updated!!! BOM and manual is coming soon
