201 modeli
Hardware Two small pins, I used a sewing needle cut down. Two small springs, about 4mm diameter. (One for the mag catch and one for the BB stopper) One BB Printing Print on the edge as shown in the photos. No support needed Assembly Put…
Wydruk około 5,10 €–6,24 € nettoWstępna wycena jednego wariantu
Speedloader for the 32 acp and 380 acp magazines for the Keltec P32 and P3AT. Slide it over the top of the magazine, press it all the way down, place a round, let up on the speedloader, then slide the round all the way back. Repeat. Print…
Wydruk około 1,18 €–1,44 € nettoWstępna wycena jednego wariantu
Speedloader for the 9mm magazine for the Keltec PF9. Slide it over the top of the magazine, press it all the way down, place a round, let up on the speedloader, then slide the round all the way back. Repeat. Print it upright with a 10mm…
Wydruk około 1,47 €–1,80 € nettoWstępna wycena jednego wariantu
UPDATE 5/17/20 I have completed 2,3,4 of the updates i thought would be good. If someone could please**try it and let me know how it works with the bottom ribs I would be forever in your debt I have printed several of the speedloaders on…
This is a 3d printable AK magazine speed loader for AK magazines in 7,62 and 5,45. It was inspired by the podavach U-Loader with the goal to make it 3d printable on a standard 3d printer. It gives you the ability to load AK mags at least…
Airsoft speedloader m4/ar15 You need: 1 m3x20mm 6 m3x10mm 6 m3x10-20mm 1 m6x20 1 m6mm nut 1 half pen spring Printed with: 0.4mm nozzle, 3 Walls, 15% infill and 0.16 layer height. Message me if the tolerances is too tight for your printer.
Speedloader for multiple types of magazines. Print one body then the Insert type/types you need and switch out just the insert. Easy Disassembly. Springloaded. Quick change insert/part replacement. 100% 3D Printed.…
Update I have re-moddled it as the old file was a bit of a mess, new file and STEPs in the ‘Remodeled’ folder in the file list. (The fullsize versions still use the same mag catch.) Also, please use the print orientation shown in the…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and i think every…
G36 speedloader created from several 3D models- combining expierience into a speedloader who can load 10 bullets who are on factory rail and inserting induvidual bullets (5 in short version or 10 in long version). Simple model to make…
Just a must have speedloader filling tool. couldn't find one over here, so designed it. Have Fun! and keep playing. Category: Sport & Outdoors
I printed from ABS. Place it on the reverse side to print a stronger pin than in the photo. Use support! After printing, stick anti-slip material on the back and top for better performance.
Made to work with Ludex m4 and m16 speed loader, also works with Oden M12. Should work with other sidewinder clones. Ludex m4 mag speed loader Oden Sidewinder m4 mag speed loader I designed this to have an easier and faster way to load my…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
Uses m3 screws and bolts instead of the less common and weaker m2 screws. the spiral plate, a common fail point, is significantly reinforced. You will likely need an assortment of fairly long (25mm+) screws.
This is a bottle I made for making filling my small Speedloaders more conveniently. Just pour BBs insinde the bottle or use it as a shovel inside the BB bag, put on the lid and fill your speedloader. Use the cap to close the bottle and…
Airsoft M4 to AK speedloader adapter. Made to fit: https://www.printables.com/model/964901-airsoft-speedloader-m4ar15 Needs to be printed in PETG. 0.4mm nozzle, 0.12 layer height, 15 infill and 3 walls Support is needed.
This is a 3d printable AK magazine speed loader for specifically for AK magazines in 5,56x45. It was inspired by the podavach U-Loader with the goal to make it 3d printable on a standard 3d printer. I simlply took the magazine adapter…
UPDATE - Also fits Well Pro AK12 . Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some…
Exactly as the title indicates, this is a speedloader for Taurus GX2 and GX4 mags. Print upside down and no supports are needed.
Remix that you can print it flat on the printer (with support)
Easy to print, easy to assemble, and easy to use. Meant to help hold down your follower tab while you load BBs so that your thumb doesn't have to. The guide tabs help keep your speedloader from slipping off. Use the catch portion to grab…
Print with brim, without supports
Hello! Some days ago i came across " 6-Shot Disc Shooter " by uhltimate and i quickly fell in love with this toy and so did my 16 year old cat that likes chasing the discs haha.. First of all i want to say huge thank you to ulthimate for…
(Extended Grip): This is a remix of the Rubber Band Gun MKII by EJTH with a more extended grip. The short handle bugged me especially because the back corner would jab into my palm. So, I made the grip bigger. This model includes the…
Please feel free to remix the design and print for selling it, please upload remixes. G36 speedloader for easy and quick magazine loading, first couple mags are loaded in same speed as with loading using fingers, diffrence is felt when…
[edit 14.2.26] Some improvements based on user feedback. New cap and shaft design features tighter swirl fit and better geometry, included bigger button and reduced file size. New version of push-button design. It features countless small…
This is a speedloader for the standard Pardini SP 5 shot magazine that I designed. I use it mainly so that I don't get oil on my hands from certain brands of ammo. https://vimeo.com/939679785
I made an exact replica of the original VFC Speedloader adapter, because I lost mine. I tested it on a V2 416 mag and it worked fine. this probably works with other brands as well. Give it a try and submit some feedback please.
This funnel fits most speedloaders and most highcap magazines. It has a rounded interior to prevent the balls from clogg
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
Arex delta / Beretta 92 speedloader 9 mm. Printed in PETG, 3 perimeters, 20% infill. If you change scale to 105%, works with Arex delta 2. This is reuplod from Thingiverse. https://www.thingiverse.com/thing:5027053
This is a speedloader created some time ago, for FX impact high cap magazine .25 Add a tiny bit och grease on the small contact points, might be a bit stiff the first couple of uses.
🟪 UPDATE 3.8.2026: A new version has been added, featuring a top and a movable bottom plate. So two parts need to be printed here. The bottom plate is guided along an axis and pushes the darts completely out of the speedloader into the…
Magazinerweiterung bzw. Speedloader für HDP50 mit Picatinny Schiene.
I remixed the Speedloader from Bigjay532 to fit my Tanfoglio. Tested in PETG and ABS+. Printed upright with support.
Now this took me some effort. This is an analouge to the Odin, yes, however they only share the same principle, (and naming conventions because irony). Chernobog has features. Hand crank for loading with one hand holding magazine with…
Doporučený materiál: PET-G Doporučená výška vrstvy: 0,2 mm Pro tisk nejsou potřeba podpěry. Pro zvýraznění textu je použita změna barvy vrsty. Pro montáž je potřeba šroub s válcovou hranou a vnitřním šestihranem M3 x 14 mm. Samojistná…
Designed this to use as a speedloader for WE GBBR magazines. Holds 30 rounds and with the plunger effortlessly pushes the BB´s in to the magazine. It has a witness hole near the open end of the tube so you easily see when you have reached…
paredzēts drukāt no PETG. Slāņa augstums 0,20 ar 4 perimetrs un 25% pildījumu
***UPDATE!!! → Added a extra model for the SIG XM7. The normal Speedloader will fit as well. Its just so you have the right description on it. Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by…
Modelled for: SPEED BEEZ® Speed-loader for Smith & Wesson® L Frame 38/357 Six (6) Shot (Models 586, 686) the Original “Ejector” SPEED BEEZ® Smith & Wesson 686P Plus Speed Loader 38/357 Seven-Shot the Original “Ejector”
General: Speedloader for 30 round Pmag magazine. Split in two to allow printing on smaller print beds. Put the magazine into the bottom part. Use the “Pickup tool” to pull rounds directly out of the box. Slide the pickup tool into the…
Both clip and loader require changes in orientation before print. Loader require support (check if support is properly generated in magwell) Update: added slim and compact version print without any support Infil: 20% Printed in: PETG…
This SpeedLoader adapter is designed for my Glock 17 Gen5 magazines but should also work with other airsoft glock or other pistol magazines. It helps streamline the reloading process, reducing strain on your fingers and making mag loading…
Airsoft BB Can / Dispenser / Speedloader / Magazine
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
This thing was made with Fusion360. Fill it with magazins and pellets, shake it, remove the unnecessary pellets, press the diabolos into the magazines, plink! Have Fun It would be nice if you could post a make! ;)
A simple one part tool used to load 40mm Airsoft grenades with 6mm BB's. Wanted to make something that makes loading airsoft grenades faster but that also didn't require long printing times and would be independant of BB capacity. Comes…
An optimized slide for Glock 19X (remix)
Speedloader in flexible TPU for 357Mag Ruger GP100 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 0,15 Infill: 20% Filament: Devil TPU Black Notes: Print slow! Real slow Category: Sport & Outdoors
A simple speedloader for CZ Shadow 2 mags I made. Wasnt a fan of the other models out there so heres my version. Feel free to remix if you so desire. I printed mine in PETG with a .15mm layer height and 40% gyroid infill with 3 perimeters…
Remixed the version from rcloutier1 so that it fits and works with G&G:s UMP magazines. An apadpter for G&G UMG magazines for Odin sidewinder speedloader. Printed on a Ender 3 V2 with 3 layer thick walls for a little extra strength. It…
Another ASG Dan Wesson speedloader, but unlike any I have seen so far, this doesn't require twisting! Just push it in until it snaps. No glue, springs or other stuff required, everything is printed. Tested with only with airsoft shells.…
***Update 10.11.2026 → Due to commiunity feedback, I reworked the adapter to a front loading design. The top loader wasn't working with all magazine variants. I'll keep the TL online for everyone who wants to try it, but be aware, the new…
Made my own simple 9mm Speedloader. Haven't tested it with a lot of Magazines yet, but works great with my Beretta 92X. Print it laying down with ONLY Perimeters as walls. No infill.
Doporučený materiál: PET-G Doporučená výška vrstvy: 0,2 mm Pro tisk nejsou potřeba podpěry. Pro zvýraznění textu je použita změna barvy vrsty. Pro montáž je potřeba šroub s válcovou hranou a vnitřním šestihranem M3 x 14 mm. Samojistná…
This is a speed loader for the Nerf Rival Kronos. Similar to other speed loaders it holds 5 balls and allows quick loading of them all at once. This model has a sliding pusher to grab onto instead of having to use your fingers to touch…
Printed in PLA+ 40% infill 0.2mm layer height, add supports to all overhangs and print on the flat side with no text. Or whatever works for you, roughly 2 hours of print time. Modelled using an Action Army 50RND mag, apply firm pressure…
I noticed a unused sliding lock at the base of the magazine. Maybe it was intended for a speedloader, but Zuru but never released to the market. So I made my own speedloader. I printed this on my modified Ender 3 v2 with the following…
This is a speedloader I have made to load my Nerf Roughcut much faster. Being a shotgun, the Roughcut runs out of ammo fast and takes too long to load to be practical for many fast-paced games, so I made this to help quicken the reload…
Colt 1911 KWC Mag speedloader adapter co2 cartridges Tired of having your fingernails destroyed by those horrid pointy sliders? Wait no more print this. Will work with 1911 mags with co2 cartridges. Video: Print it in ASA/ABS or something…
Check out the manual in the link below: https://youtu.be/jF4x1P-BDzM
***UPDATE 13.05.26 Added a new variant, that will automatically reset your STOP ON EMPTY mechanisim, everytime you load a magazine. The Idea was thought up by Manamuner, a member of the Heavy Recoil Club. To honor his contribution this…
Simple funnel for odin speedloader with a cut out for the bar that goes across for the screw. sits nicely with or without the rubber insert. Print upside down (Use a raft if doesn't adhere well)
UPDATE - With help of the commiunity, the Front Loader design could be improved to load easier. Thanks to "Delta Mike" of the Heavy Recoil Club! Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by…
Here is my take on an simple Adapter for Odin like speedloaders So far I tested it with a Cyma G36 High-Cap magazine and it fit perfectly. If the dimensions don't work with other brands, feel free to message me. Parts needed: M3 x 20mm…
***Had to name it in this wierd way, because Glock is very protective of its name. I should've expected this beforehand, the biggest producer of ...."Horse milk".... will be a bit awkward when its about reading his own name. "Big Stick" -…
This is a speedloader, or something like it, for the LMG I designed. You just insert the links, and it holds them in place while you load darts. ------------------------- I have added a compliant pawl plate, which means it's a single part…
Hello, this is my old scrapped idea for sr25/scar-h odin speedloader adapter. Im sharing this as “incomplete”, i can share step file if someone wants to remix it. In theory this adapter should work, but in reality i dont know
Don't know why, but this was one of the most requested adapters?! Print it for yourself or for friends. Use it, love it and leave a like. I used a “Pro Shop Speedloader” to design all of my Speedloader Adapters, it will work with…
Speedloader remix + Forerunner specific speed loader holders for use with Forerunners with picatinny rails Speedloader remix: longer pusher to maximize space, uses two spare nerf shell screws or 4-40 3/8" screws for assembly instead of…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
***UPDATE 27.04.2026 -Added V2 of the adapter. It will automatically reset your "stop on empty mechanism". Big thanks to "Manamuner", member of the Heavy Recoil Club, who suggested, and tested it for me. ***UPDATE 08.08.2025 -Front Loader…
If you are making one of these, consider sending a tip - every dollar helps to create more things like this and encourage more open sourcing of designs. A friction fit guard ring to put over your speedloader locking button - it also…
***Update 09.06.26 Edited the model so it will also fir UMP 9 Magazines. Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't…
No need for any support. But I use brim for the fast loaders. Brim type - Outer brim only Brim width - 2mm is enough Brim separation gap - 0,3mm The brim separation gap still helps with stability and it is easily removed. Also, I use 101%…
Replacement Lid for the Cheap Winding Speedloader for easy unloading of mags. BB stopper is only necessary to stop bbs from comiing out while transporting the speedloader in a bag Lid might need some sanding at the edges to move freely I…
Remixed for Walther PK380. Single stack 380. This took a little work in tinkercad to keep the thick walls and the right size for the plunger, But it turned out ok, and fits perfect. I modded the pla file and upsized it for printing in…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
This Speedloader Adapter was made possible through the help of Björn from "Pfitzner Waffen", who was an absolute Lad and provided the magazine. Be a trooper and give him some love! His Store → https://www.pfitzner-waffen.de/ ---Don't you…
Attaches to the speedloader with glue, so it is (depending on the glue) a rather permanent solution. You can potentially use strong double-sided adhesive instead. Add glue on the back in the groove at and at the outer edges, away from the…
speedloader for normal and practice rounds for G36 and HK416 mags with Nato 5.56 clips
This speedloader with an ordinary PET bottle thread and a cap shall be printed without supports and with fine print settings. I use 0,16 mm layer height and PETG to ensure more durability for higher summer temperatures. PLA is fine, too,…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
Just took the original STL and added some MOLLE-Clips like in https://www.thingiverse.com/thing:4694277 so it is a "real" MOLLE-thing now :) Supports are now required! A few weeks ago I got a AR15-style speedloader that can hold like 300…
This is a speed-loader loading block for the Smith & Wesson K-22 revolver. It holds 48 cartridges in groups of six. It's designed to hold a HKS speedloader, and fits Smith & Wesson K-22, M 17, M 18, Colt Diamond Back and Dan Wesson .22…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
***UPDATE 13.05.26 Added a new variant, that will automatically reset your STOP ON EMPTY mechanisim, everytime you load a magazine. The Idea was thought up by Manamuner, a member of the Heavy Recoil Club. To honor his contribution this…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
Speedloader adapters for the NorthEast FAMAS magazines, compatible with both regular and Odin style speedloaders. In addition to their primary function, the adapters also have an included BB ejection lip which can be used to easily remove…
With this tool you can easily load your Zoraki M906 magazine. Printing: PLA, ABS, PETG 20-30% infill Suppurts needed (ZigZag works fine) Print on bottom flat surface
This is a simple design for a .22LR Speedloader. It works well with a S&W Model 17 Revolver. The whole design is meant to be glued together using superglue. Materials needed: 1x M3 screw 25mm long 1x M3 nut 1x spring with a diameter of…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
The Repeater Pro Speedloader is a 3D-printed tubular stripper clip designed by Luchathor to quickly reload the Dart Zone Max Nitroshot+ Repeater Pro lever-action blaster. Featuring a double-stacked 12-dart capacity, this device fully…
Not much to say here. I'm too lazy to design a mag latch so just push hard when cranking the speedloader. There is a tiny window to the BB channel. I was going to shove a rubber piece in there to stop BB from coming out of the adapter but…
This is my first ever attempt at 3D modelling and printing. As much as I love the Odin speedloader, one thing I didn't like is the handle coming off so easily after a while. So I designed a replacement handle with some minor improvements…
A simple speedloader for the Swiss military 9mm pistol P220 / P75 with single stack magazines. Possibly works for P210 as well. Print as is standing on the cross without support.
I was excited to make MrFlippant's excellent Bowden Speed Loader, but I have about 100 Omron d2f style microswitches in my parts bin, and none of the one listed in the BOM, so I did this quick remix. All other printed parts besides the…
Don't you hate to load your GBB-Magazines with a wild three-piece construction, thought up by some exploited taiwanese sweatshop worker?….. Well, atleast I didn't like it. Thats why I made some Speedloader Adapters, and I think every…
