318 modeli
Rat gas anesthesia masks for stereotaxic surgery. Designed in Fusion 360 to replace an original part. Requires an M4 screw and a nut, and also a little bit of glue to hold the nut. I recommend printing the thicker version. Enable supports…
Wydruk około 1,25 €–1,52 € nettoWstępna wycena jednego wariantu
I recommend printing the test scary hand stereo knob to see if it will fit on ur stereo knob before printing the whole hand and possibly wasting a whole lot of filament
Wydruk około 0,24 €–0,29 € nettoWstępna wycena jednego wariantu
Ford F250 double din 7" stereo bezel printed in PETG
Wydruk około 1,12 €–1,36 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Studenti nebo vyučující vytisknou mnohoúhelníky k pokrývání roviny pro trénování prostorové představivosti a modely pro výuku vlastností elementárních těles a vzájemných poloh přímek v prostoru.
Wydruk około 0,08 €–0,10 € nettoWstępna wycena jednego wariantu
A repair job to a hundred year old stereo viewer that had some missing parts. Here's a vid showing how the bracket is assembled: Except for the handle, all parts print without support. If you found this useful, it would bring me great joy…
Wydruk około 1,25 €–1,53 € nettoWstępna wycena jednego wariantu
Držák na uchycení- SILVERCREST Soundbar Stereo 2.1 - na vrchní část Tv samozřejmě je nutné si první ověřit rozměry vrchní části Tv. Základní rozměry jsou na fotkách, pokud máte například tencí Tv bude chtít držák doupravit ať už úpravou…
Wydruk około 1,91 €–2,33 € nettoWstępna wycena dla PETGMateriał u źródła: PET
AA Rear shell is here! USBC Rear shell is here! This model is designed specifically for the Funny Playing IPS screen mods. PRINTING: I have had successful prints with 0.4mm and 0.6mm nozzles at 0.2mm layer height with PLA, PETG, and ABS.…
There is a free and paid version of this software 3D scanner. Since I released this free version of the program, I've put a lot of effort into creating version 2.0 of the scanner. It's only available in the paid version.…
This model is featured in figure 3.12 of Visualizing Mathematics with 3D Printing . Video . Stereographic projection is a map from the sphere to the plane: Imagine straight lines going from the north pole of the sphere down onto the…
XY Clip For microphones with a diameter from 19 to 25 mm. The brackets are available in two different wall thicknesses. The easy-to-print clamp gives the correct setting for XY stereo recording (90 degrees). An adapter screw (3/8 inch to…
ORTF Clip For microphones with a diameter from 19 to 25 mm. The brackets are available in two different wall thicknesses. The easy-to-print clamp gives the correct setting for ORTF stereo recording (110 degrees and 170 mm capsule…
Replacement stereo surround of for the Land Rover Defender TD5. Print instructions Material: PETG Layer Height: 0.3mm Infil: 30% Perimeters: 4 Top Layers: 3 Bottom Laters: 3 Support: Yes
Designed to replace the weak original battery plug covers … :) Material: ASA/ABS
Length: 180mm. Six models in total. Two bar variants: 1. with 1/4-20 and 3/8-16 threads. 2. with bare holes for (1/4-20 and 3/8-16) brass inserts. Four screw variants: 1. Long screw with 3/8-16 thread. 2. Short screw with 3/8-16 thread.…
Removal tool for Clarion Car Radio. Its little thicker then original tool, but PLA is not strong enough to work with original thickness. I used it on my own stereo and it worked perfectly, it needs little bit force, but I did not damaged…
After a long search, I managed to make a 3D printed stereography sample. The three-dimensional cube can rotate when you rotate the position of the observer, light source or object. This project is inspired by the work of the Russian…
Aftermarket stereos/head units for pre-facelift Fiat 500 (years 2007-2015) usually require removing original diffuser and vents which leads to air blowing into the back of the screen and everywhere under dashboard. This model is not as…
Designed for the i30N speakers. Some changes from the original model from Haba1205 (thank you btw..) Added some holes for wires and M3 screws. Maybe you have to drill them a bit. Also thanks to Hannes…
Stereographic projection-Love 123D Deign： https://www.youtube.com/watch?v=tqWkFL4mNzw Print Settings Printer: cr-8 Rafts: No **Supports:** No Resolution: 0.2 **Infill:** 20 How I Designed This =================== Category: Art
This mount conforms to the dashboard and tray contours of the 2015 and above Chevy Colorado and GMC Canyon. There's room for double-sided tape on the back of the mount in the tray area and in the front of the mount on the stereo fascia -…
Frame for Blaupunkt 1-din car stereo from 90's. It holds radio in your dashboard. This was used for example in Blaupunkt Paris RCR, Lubeck CC etc. Most of them had two holes for screws, but I made also single hole version. If you want to…
I made this model to blank off a single DIN headunit slot to add switches and LED lights. It can be modified to add holes in CAD or you can drill them. I recommend 100% infill and PETG at a minimum for in-car parts. If your country is…
Uses the screws and spacers that came with the amplifier board kit. Steps to assemble: 1. First prepare the top part by fastening the spacers with 4 screws on it. 2. Place the board into the bottom of the enclosure 3. Slide the top part…
The model can be resized, mine has 15 cm of diameter. It can hold a candle and the projection will change as the candle gets smaller. I can make custom projections! Send me a message and we can discuss it. Print Settings Supports: Yes…
This is 3D printed variant of https://www.instructables.com/Portable-Bluetooth-Speaker-Made-From-Scrap-Wood/. You can follow the same guide because enclosures are almost identical (i used same dimensions). Two holes on front side are for…
I made this simple enclosure for the car stereo which I'm using as a home stereo amplifier and a record player. Should fit any standard 1-DIN car stereo head unit. Supports are needed for the round feet at the bottom - organic work best.…
Printed w SLA. inch scale (1/12)
This model is designed to fit the dash of a 1984 K5 Blazer. I believe it should fit 73-87 (91). This mount is designed to replace the flimsy metra dash kit. You will still have to trim your existing gauge bezel and metal dash with a 7.25"…
Basic case for single DIN car stereo detachable faceplate / fascia. The interior of the case is 172L x 49W x 30H and should hopefully suit all detachable faceplates, including those that have large front knob. The hinges use a short piece…
Double projected letters which can be read twice – from the right and from the left point of view. Nice touch for a present. As initials they can be used for table decorations. Some letter combinations can be printed right away. Others,…
This is a basic double DIN car stereo mounting bracket with mounting ears and side screw brackets. I needed a mount for a truck dash. It will mount to a properly sized hole in the dash and attach with 4 screws. There are ears for the side…
No screws required, 2 clamps are used instead to hold the 2 enclosure parts together and also serve as feet. Steps to assemble: 1. Place the board into the bottom of the enclosure. 2. Place the top of the enclosure over the bottom one. 3.…
Stereo brackets for mounting single or double din head units in the 1991-1999 3000GT/GTO. Designed to be printed flat with no supports. Supports will make your holes a bit more clean. Suggest you print these with a higher temp material as…
This design was inspired by henryseg's Stereographic projection. I fell in love with the Hilbert curve and after seeing what Henry made I decided to make my own projection. Print instructions Category: Math Art Summary This design was…
This model is featured in figure 3.13 of Visualizing Mathematics with 3D Printing . Category: Math
Basic 3D printable enclosure for Rockler Woodworking's bluetooth speaker kit.…
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/2Ce1oPrpMBB The feet on my Denon stereo receiver stuck to the painted shelf it was sitting on. I went to move the receiver and the center of each foot…
I designed this to utilize the empty space where the stereo head unit was when I installed an Android unit. Prints in two parts. Print the faceplate facing up and break off the designed-in supports. Glue the box into the back of the face…
I made this model to align my cheap USB cameras for stereo imaging. It's press fit for the PCB, and enough space to add some glue to fix the cables. Distance of the cameras is 35mm. I'll add a cover plate later maybe with a strain relief.…
This design combines two 4x microscope lenses together to create a stereoscopic 3D macro lens, with 2x magnification and a 5mm stereo baseline. It has been designed to be shot handheld in the field using a flash for lighting, rather than…
A bracket that fits around a 1DIN aftermarket stereo in a Skoda Fabia (Mark 1) to make it look better. Blends perfectly into the shape of the dashboard.
Works perfectly for any kind of older stereo with ISO connectors. Used no supports, only used Brim for better adhesion to the plate. Printed on Prusa I3 MK2 , Prusament PLA ( 1,75mm ) blue color, Infill 15% !!! Not my my make, only…
Design Based on the RBT Mount. Fits stereo Realist size slides (and other vintage stereo film cameras). Fits perfectly in my Kodak Stereo Viewer. Print 2 (one in black, one in white) and clip them together with the film inside.
an adapter for mounting 1 DIN radios in GM format slots
This little gizmo is used to view stereoscopic images on a postcard-sized printout. The centers of the two images should be 64mm apart for optimal results (that's the interpupillary distance this was designed for). The lenses I used were…
This is an adapter for the raspberry pi camera (rev 1.3; you can get it for 3-4 USD on Aliexpress) and is used to put it on the eyepieces of any stereo microscope with 32-33mm diameter. It has spaces so as not to press on the…
This is a lamp that projects a hexagon pattern on the ceiling (or floor), created entirely in openSCAD. The pattern is customizable within the openSCAD script, and I've included an example of projecting squares. Parts: shade (printed)…
This speaker mount reuses two screw posts from the front shell as anchor points. No cutting required, just drop the mount, install a second speaker (either standard or premium - see below for explanations), run the wires along the shell…
See the attached (recommended print orientation) Not compatible with xxxxAlpha HGS Molecular Models. But compatible with my ball-and-stick model.
Friend asked for a JBL Flip 5 bike mount to have a stereo system for his daily commuter bicycle. Although the JBL Flip 5 is sonically not quite up to Audicitve standard, a music loving project like this deserves support. So here it is -…
Printed w SLA. inch scale (1/10)
A easy support system for my Rode M5 matched pair Microphones to record in XY-Stereo Mode. Center hole is a microphone thread 3/8" to mount it directly on a microphone stand. The two other holes have on the top also a 3/8" thread to…
I made a customizable version of henrysegs ingenious design that uses stereographic projection to project a grid from a sphere to a plane: http://www.thingiverse.com/thing:202774 You can simply upload an image with the size of 75x75 and…
If a single point light is placed near the North pole of the sphere, a grid is projected in the shadow.
These are Case Parts to make a 500 Racks in Stereo or Mono. It's parts of a (DIY) Audio System with 500 modules. The Modules that can used with the 3d files are: EXT VPR EXT 51X STEREO VPR STEREO 51X Additional PCBs and needed parts and…
Pioneer AV Stereo Receiver VSX-604S volume control knob. Printed in PLA Creality Ender 3 V3 SE printer Resolution 0.1 I
Headset support for Jabra Evolve 20 MS Stereo and control button Additionally required M4 nut and M4 screw (at least 20mm length). I used a DIN316 wing bolt
Basically just a keystone module with a 6.3mm hole, to mount jacks for 6mm panel openings. The thickness of the “panel” is 2.1mm.
StereoFreq guitar pics… These are my own design. I've been using them for quite some time. I typically print the FDM pics with PLA2 from FilaCube. They shred rather quickly compared to nylon pics, but they only take about 5 min to print…
The basic design by 3dGringo looked good and several people requested design files, so I quickly did a reverse engineer of the part so that others can make spinoffs. Some cool ideas included adding charging USB ports and additional plugs.…
simple case for cheap TPA3116D2 2x120W class D amp board
This is an Arduino-controlled ring light for stereo microscopes with a 48x0.75mm threaded nose piece. This is one of the most common sizes and fits my vintage Olympus unit. Other thread sizes for which commercial ringlight adapters are…
These holders are for supporting the Rode M5 mics at a 110 degree angle to each other within the Rode Blimp 2 windscreen. A standard XLR connector will not fit on the back of these mics in this configuration, you have to get creative and…
Designed this to be a cigarette holder/dispenser, that dispenses one smoke at a time. It can be attached to a keychain or lanyard. There are 2 different sizes for the bottom piece. Holds 10 smokes effectively. Any more than that and they…
Case for Raspberry Pi 5 for adding two INNO MAKER MIPI 7251 RAW Cameras Edit: been having issues getting the 7251 to run so will be trying the OV9281 instead which should have better support. and a Adafruit 9-DOF Absolute Orientation IMU…
The .stl files are oriented in a way that allows the logo to be printed into each piece (top/bottom). To do this, print the logo first, with a .4mm nozzle and don't remove it from the print bed. Then, with the logo still on the print bed,…
This is my first model to create. I wanted a way to mount two of these to my camera for a field mic type setup. I added an block for each to sit on, rounded them to match the handle part, then cut each diagonally, so it would sit on an…
Stereonet/Stereographic projection visualiser, designed for geological joint mapping. Print Settings Printer: RepRap Fisher Rafts: Doesn't Matter Supports: Doesn't Matter Infill: Some probably required Notes: the three planes may require…
Note: This stand requires the original mount that with AC511M to work.
This is a mount for the Infiray P2Pro with microlens on a stereo microscope with a diameter of 54mm. The working distance of the stereo microscope is 100mm and the mount is approximately adapted for the P2Pro with microlens. This allows…
<DJT LINK TO VIDEO> Haven't seen wide stereo contact mics before so I made some. They can capture some neat sounds. Pretty rugged - passed the below tests: Submerging in water for hours Running over them with a Honda Civic Submerging in…
Model created in Fusion 360, and included in the project file to allow easy modifications. The Phone holder part is designed to take a phone with a basic soft cover fitted, to fit a bare phone it would be necessary to print a padding…
designed for the boss BVCP9700A, not sure if it fits other models
This model is a viewer for stereoscopic slides. Could not find one anywhere so I made one myself. The model consists of three parts. (1) The lens housings are supposed to be screwed to allow some change in the distance to allow minor…
Modelování těles pro výuku stereometrie pro studenty SŠ. Studenti vymodelují 3D tělesa v CAD programu, vymodelované tělesa dovedou až do finálního tisku.
Blanking plate with holes for 5 Carling/ARB switches. Also incudes model with no holes. May redo as the ARB switches seem a bit smaller than the cheap ebay knockoffs I bought. I don't have a stereo just use an amp with bluetooth.
Adds another VGA hole to the HDMI version so that you don't have pick between the HDMI or the VGA version
This is a friction faceplate that covers the gaps left when installing an ID-5100a into the CD changer console spot in a Lexus LX470. It can be printed on a Prusa MINI (cause that's all I have) and must be printed with supports. I suggest…
When I went to install an Atoto A6 (Double din touchscreen) stereo, I noticed there was gaps on the side due to the width of the original head unit. I did a quick google search for solutions, and only found one, so decided to whip this up…
I needed a stereo RCA to RCA adapter, It was Sunday, all shops closed, and I had spare connectors in my electronic parts box, so ... here it is, simple but efficient. It may be improved a lot but it doesn't deserve the time required to.…
A slider knob for a Teac EQA-20 Stereo I included my 3MF print file for the settings I use. I printed in PLA with .1 layer height to make sure the tabs on the back print properly. I would not print it with a layer height larger than this.
This amp comes without a case except of top and bottom plates. So if you are going to leave it on the table, anything can touch the electronics from the sides. I tried to insert it into a speaker case, but this way I lose access to amp…
This model is a housing for a stereo binaural microphone. I made this in the likeness of Crown's SASS mic for my nature recording hobby. It's posted here in hopes that you can make some use of it for your own recording adventures. The 4…
I made this to adapt an old speaker/mic to my QMX. The spacing between the 3.5mm audio plugs is 12mm. It will only plug in one way because the other way the power cable will block it. The 3.5mm plugs I used have 7.9mm ends which depending…
I remixed this to utilize the empty space where the stereo head unit was when I installed an Android unit. Prints in just one part. thanks to @jiggersplat_114037 for the perfect size.
The Jabra Evolve 80 is a very good headphone, but unfortunately its headband is defective from the factory. The material is not elastic enough, so it breaks after 1-2 years of use. I was sorry to throw it away, because otherwise it works…
Rockola wall speaker stereo emblem.The S sticks out a bit to allow for a top layer change so you can change the color. Notes: White until top layer, then filament change (M600) to red.
This is a easy-printing housing for an ELP stereo webcam, which comes as a bare board with fisheye lenses: the ELP-960P2CAM-L180 It accepts a 1/4"-20 nut in the bottom to allow tripod mounting: you may want to glue the nut in place (I…
This adapter works on Leica S and M series stereo microscopes with a 38mm thread at the top. It On these microscopes there is no lens built in to the top port, and the image coming through is focused to infinity. As such all that is…
Simple print. Use a dark opaque material. Designed for use with 38 mm OD barlow lenses.
Just a Nightmare Before Christmas inspired Stereo knob replacement. printed in PETG to handle the heat inside a car. supports needed
This is the 1 din stereo mounting bracket for the 90s GM vehicles. I made this for my 1996 Impala SS. The radio sits flush as shown in the pictures, and its centered using to the dash bezel. I guess the bracket fits the S10 pickup truck…
Used: Printer: Creality Ender-3 S1 Pro Layer height: 0,2 mm Nozzle: 0,4 mm Filament: 3DFox Economy Basic Black PLA Supported
This minimalistic enlosure is made for the little 502-MT Mini Amplifier and maybe some others in the category of cheap amps.
Allows you to put two microphones on one mic stand and configuring them in any stereo configuration desired. Choose from either 3/8" (European) or 5/8" (US) threads. Do not overtighten the knobs when installing. The knobs may stick to the…
Stereographic Projection based on the excellent work shared here: https://jasmcole.com/2014/11/01/stereographic-lampshades/#more-650 I used Blender's "Solidify" modifier to add various thicknesses to this model for printing. I recommend…
This soundbar is really useful and functional when you would turn up the volume of your phone without any electronic device. It can be printed well with Tree support (On building plate only) use PETG. 0.2, 3 Walls. Suitable for cups with…
High res version created locally with openscad and this script: http://jsfiddle.net/threonin/3j2c2pwe/ This took over 2,5 days to render at a resolution of 500x500. Source of inspiration https://mcescher.com/ Category: Math Art
Schematic provided. There is a 3D printed router template (that I forgot to take a pic of installed) that you can screw into place first on the external panel and use a 1/4" router bit with a bearing to trim the hole for the line out mod.…
Remixed to fit metric double din size (180x100mm). Works with aftermarket android double din radios.
