Liczymy pasujące modele…
Remixed to add 1.5mm to the rail slot to prevent flashlight from sliding forward/backward. Printed in Hatchbox PLA Pro. Fits pretty snug and may require a little force to get it seated.
Wydruk około 0,22 €–0,27 € nettoWstępna wycena jednego wariantu
This is a 3D printable version of a light cover that's also commercially available. I saw no reason to spend $17 plus shipping for something I could easily make myself, and customize to my liking. It's sized specifically to fit the…
The original lens bezel is prone to break if tightened a bit to hard. This usually happens if the lens does not snap into place and you don't notice it while tightening. In the original bezel there is a small groove for a rubber o-ring,…
A remix of Lupo's Streamlight TLR-1 Dummy I am also including different rail keys for adjusting the placement on picatinny rails. I have included the original switch as I did not modify that. Hardware: 2x M3x20mm bolt and nut (for clamp)…
*** Airsoft use only*** See read me for hardware requirements. Easily mirrored to orient the light on the other side. A pair of rock solid mounts for the Streamlight / Surefire Scout pattern of flashlights. Features: -Center lug in…
Rail keys for the Streamlight TLR-1 in several different "sizes" “0” is centered on the hole, each number is the mm offset from that center. Fits an M3 nut in the slot.
45° mount fits pretty tight to the rail surface, won't likely fit rounder rails. Inline mount is offset just enough to get to the MLOK bolts with a ball end Allen key. A longer mount that placed the flashlight past the bolts didn't pass…
A better button panel mount for Streamlight Button Panels! The ones that come with the weapon light are garbage, so I made a rock solid mounting solution! Mine doesn't have ANY wobble or movement. It feels great! I use a Streamlight…
None of the locking keys of 1913 style provides a great fit for my Streamlight TLR-7X on my Sig Sauer P365 XMacro. So I made one for myself. If need to deal with real recoil obviously you'd want to print in some durable material. I…
Holds a full size Streamlight Stinger tightly. Designed to mount with a 1/4" bolt. Made this to mount on my roll cart, to hold my flashlight when not in use. It should load properly aligned and print with no supports. If for some reason,…
Molle Flashlight mount for Streamlight ProTac-HL-X. Printed in MatterHackers Ryno Pro. Sliced with Cura at .2 layer height, 100% infill, 5 walls, and used Fuzzy skin on outside only. I printed it vertically as shown in the picture with no…
A clip on/clip in hard hat mount for the Streamlight Stylus Pro (½" in diameter) and similar pen style flashlights. No supports needed. Printed in PLA+ I printed with a .6mm nozzle and it took about 11 min. If you're running a .4mm nozzle…
3D scan of the Heckler & koch USP 45 with Streamlight TRL-1 HL. remember to leave a like and comment! High resolution scan. 2 million triangles. the STL is 100mb.. recommended setting for PLA 0,4 nozzle 0,2 layer 20% infill gyroid infill…
Streamlight doesn't sell these as far as I could see (unlike TLR-1, 3/4, or 7/8 keys) so I cloned them. Now you can replace your keys without buying a new $300 light.
This is a quick and dirty change to Macmade's Twin 18650 Holder. This adds 3mm of height to accommodate Streamlight SL-B26 18650s and potentially other brands that include a battery management circuit on board. You can download the screw…
For the off chance that you lost or broke your flashlight; here you go! Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: Yes Resolution: 200 Infill: Whatever you feel like Filament: Matterhacker PETG…
Streamlight TLR-7 HL-X Sub Lens Cover This lens cover is a great accessory for protecting your light while at the range. It helps shield the lens from gunpowder residue, keeping it clean and clear for optimal performance. Printed with…
The summary says what it is and does. I created a bracket to snap a Streamlight Nano onto the front post of my Lee Turret press so I can see into cases a little better to verify powder charges before seating bullets. Not the prettiest,…
Wanted a better mount than the one included with the HL-X Pro, found some files that would work but are too big and intended for older model, bigger tape switches. The new one is quite a bit smaller and doesn't have the bump(?) on it. So…
A modification of the TLR1-HL key to bring the light closer to the trigger guard but not bind on the guard. This is similar to the TSW-99 key. I lost most of my keys for this light, so I had to print a replacement. Note: some…
Edited for stronger Molle Clip as it now prints on its side so the layer lines are horizontal not vertical. Still needs supports on print bed. Much Stronger molle Clip !!
This is a tape switch holder for your Streamlight ProTac weapon light. Use 2x M3x10 bolts and 2x M3 nuts instead of the hardware that comes with the light. Included are the STEP and STL files.
Small flashlight adapter that fits a standard GoPro mount, the flashlight snaps into place with some force applied. I created this to use on my PAPR for cleaning inside metal printers at work, but there are GoPro mounts for just about…
This model is designed to allow the Streamlight wedge, my edc flashlight, to easily be attached to a standard Picatinny rail. I have tested the piece out a bit and found that the light is securely held in the mount and the only way I…
This is an 18650 adapter for the Streamlight Stinger. Might fit other models. I removed the outer casing of the original battery and clipped off the top adapter for the negative connection and used it in combination with a spring. Covered…
Small mount to hold streamlight flashlight on wall, truck bed, etc
This is to be able to use 18650 batteries in a Streamlight stinger. It two pieces for loand in unloading the 18650. If there is trouble printing the holder right side up print it upside down with supports. Infill on spacer can be lower.…
This model was designed to act as a light proof cover and gas protector for my rifle mounted Streamlight HL-X rifle light, printed out of Overture 95A TPU in black this cover is secure without the need for external bungies however is…
Lens bumper for Streamlight Stylus Pro USB flashlight. Designed this bumper to protect my flashlight lens from constant use. Print in TPU. No supports needed.
Hardware Components M4x8 bolt M4 Nut Assembly Instructions: Slice the stl with the above settings Print the mount The tolerances are very tight on the Rail. Depending on the dimensions of your dovetail rail, you may need to sand (or…
The stock keys don't allow the VIR to sit close enough to the frame without coming into contact with it. This places it as close as it can be without rubbing and throwing off your zero.
Here is a remix on the gridfinity empty bin by Akio. i needed a holder for my flashlight that i use to check on my printers, my flashlights are like 10mm sockets they constantly disappear so needed to have a spot to put one. this works…
Resized for the Streamlight SL-B50 Battery
A friend's kydex holster was wearing off the finish on his Sig P938 and, having a Streamlight TLR-6 mounted, it was difficult to find a replacement holster. We decided to see what TPU would do, and this is what I came up with. The holster…
This is a Lens Cap for the Streamlight TLR-1 HL This may also fit the Braun - 1000 Lumen Rail Mount LED Light (This cap fits my Braun light, but is slightly loose)
Previously used the ‘F’ marked index key for a Streamlight TLR-4 on a Walther PPQ, but the light sat too far forward so I decided to make my own. I designed this to utilize both lugs so it is longer than standard keys. Using this key…
The Streamlight is tough as nails but the squishy bits didn't last. My goal wasn't fancy or elegant, just to replace them and have the ability to do it again in the future. The gasket is to protect the charging port and keep the front…
Hello! I used the following designs to create this mount: CR-10 Streamlight Microstream Holster by i_need_a_better_name on Thingiverse SKADIS Universal Hook - base and modified hooks by galvanization I printed at 100% infill in PLA with…
Printed right-side up with no supports.
Base de linterna Streamlight Enduro Pro. La impresion es sencilla. Altura de capas: 0.2 Relleno : 60 a 100% Velocidad: 150 a 200 mm/s par impresoras core xy o 60 a 70 mm/s impresoras estandar Soportes: No requiere Balsa: Requiere en un…
Flashlight Diffuser for Streamlight ProTac HL-X Settings Surface Mode: Surface (no top or bottom) OR Both (be sure to flip the model 180 so the top will be printed and the bottom will be open) I recommend rotating the model 180 to print…
A clip-in holster for a Streamlight Microstream, 2 versions, one with holes for m3 socket-head screws and one without. Insert emitter side down and clip in with a push.
This is a Picatinny rail mount for the Streamlight Sidewinder series flashlights. Some parts are required from another mount, for example a helmet mount meaning this just some kind of conversion kit. Further, a M3x30 hex head bolt and a…
My flashlight kept getting taken and not returned at work, since everyone has the same flashlights. I decided to customize mine, so there is no doubt whom it belongs to. I have included the blend file so you can tinker with it and make it…
Smoke Plug for streamlight survivor smoke plug
Takes up space inside the battery compartment and prevents shocks from jarring the batteries out of electrical contact.
Flashlight Diffuser for Streamlight ProTac 2L-X Settings Surface Mode: Surface (no top or bottom) OR Both tip will be printed and the bottom will be open. Spiralize Outer contour (vase mode) Layer Height: 0.2 Wall width: 0.82 With these…
An experiment in TPU. I wanted something to protect the end of my flashlight, and also to hold in some tinting film. Fits the Streamlight Strion HPL.
Streamlight 66318 MicroStream AAA Magnetic Holder that requires four 10x3mm or 10x2mm magnets. I printed it with supports for the battery holder spots. It could be printed in PLA, PLA+, PETG, PCTG, ABS, Etc. I printed it in a color…
Shock Cord Collar for the Streamlight Protac light. For the light cap, I used the large size One Hundred Concepts light cap. You can obtain the STL for the light cap here: https://onehundredconcepts.com/pages/email-sign-up Category: Parts
You can use this cone to direct traffic or other signal use. I used PLA Plus to print this in about 3hours using 0.3 mm layer height. Print with vertical walls set so that the print has no infill for a faster print.
simple anti roll bezel to replace yours when the original silicone one dries up and rips
A printed jig to hold a Streamlight wedge with pocket clip
Arms from the original piece will likely break on impact or just crumble after lots of opening/closing cycles. The door is under constant tension from the batteries, so I've made the arms chunkier to withstand the forces. This model…
I bought a Springfield Hellion… VHS-2(I hate the import name). I bought things to put on it. One of those things was a Streamlight ProTac HL-X, because I'm a sucker for WML's. Problem is - you can't pic rail mount the switch, as the pic…
This is a spacer for use with the Streamlight ProTac 2X-L in a UTG MLOK light mount.
Streamlight Stinger 75100 Charger Snap Mount for Multiboard .4 nozz, 3 walls, 15% gyroid, Polylite PLA Pro
Streamlight stylus series lights are tough as nails and just keeps working after years of abuse in the daily routine. After a few years you will notice the rubber beginning to deteriorate and eventually your button will be susceptible to…
Just a simple replacement button, to be printed in TPU or similar. I made three versions, one with varying thickness of the button to try to duplicate the original feel. I think i like the thinnest the best.
Works as a diffuser and flat stand for the Streamlight Wedge XT EDC flashlight. Use it as handheld or set it on a flat surface to light up a room. Pro tip: if you print from orange filament, it also serves as red cap, useful for retaining…
A Holder for the Streamlight SL B50 Battery
Scanned with a Creality Raptor X and applied to Gridfinity via the Autodesk Fusion plugin. V2 has a slot for a USB-C to Micro USB adapter. I bought this one: https://www.amazon.com/dp/B0CDP9JWVY
This is a lens cap for a Streamlight Super Tac X flashlight. It's designed to be printed with a FLEXIBLE filament so it's got a snug fit. This part will probably be too small if you print it with a standard filament. Category: Parts
A quick printing holder for the Streamlight 4AA models to attach your light to any hard surface using a screw. I recommend at least 5 outer walls so the top portion prints at its maximum strength. Some supports will be required. The…
This is a Lens Cap for the Streamlight ProTac 2.0 Rifle Light I put a thin o-ring in the grooves on the light head to snug up the fit.
A quick printing holder for the Streamlight 4AA models to attach your light to the Honeycomb Storage Wall system I recommend 5 outer walls so the HSW mount prints at its maximum strength. Some supports will be required. The flashlight fit…
This charger fits Streamlight Strion battery pack part 74175. Required additional components: Stainless Steel Self-tapping screws M2.5x10mm or 8mm: https://www.amazon.com/dp/B00YBMROKC Pogo pins: https://www.amazon.com/dp/B07FPKKK9W USB…
Replacement for streamlight button and nut. Nut is printed in PLA, Cover is printed in TPU. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2 Infill: 30% Gyroid Filament: Hatchbox PLA+ / TPU…
This is a model I created for work. I work in Corrections and we utilize chits to keep track of who has which gear items. I cant speak for other places, but at my work, everything else is accounted for, however the flashlights dont have…
Slide over hook for the Streamlight Stinger. It is the first iteration of this for me. It fits well but could use some improvements. More to come later.
Remix of Streamlight TLR-7/A Lens Cover Changes Slit light cover Double slit light cover Scaled down to 99.5% light cover (better fitment) Scaled down to 99.5% slit light cover Scaled down to 99% double slit light cover Category: 3D…
A quick printing holder for the Streamlight 4AA models to attach your light to the Ikea Skadis boards. I recommend 5 outer walls so the Skadis clips prints at its maximum strength. Some supports will be required. The flashlight fit is a…
This is a replacement mounting gromet to a 14136 Streamlight Sidewinder Compact II E-Mount (ACH, ECH, MICH, LWH helmet compatible). I actually had a mount 14055 designed to fit PASGT and ACH style helmets. Though the bracket arm may not…
I recently got a stream light sidewinder off of ebay, i wanted it to be magnetic but sadly couldn't find anything that i would fit my needs. So a few revisions and and it now has magnets! uses 0.315 magents
Replacement arm for Streamlight Stinger Smart Charger & Streamlight Stinger Smart Piggyback Charger modeled to be a replica of the OE Streamlight part, which is not available or “serviceable.” Break you Streetlight charger or maybe just…
Remix of Streamlight TLR-7/A Lens Cover Changes Slit light cover Double slit light cover Scaled down to 99.5% light cover (better fitment) Scaled down to 99.5% slit light cover Scaled down to 99% double slit light cover Category: 3D…
Very Simple holder for my flash light. inside diamter is 28mm inside height is 79.5mm used slim auto tree pla pro 220 temp .2 layer 4 wall
A lens cap for the Streamlight ProTac Rail Mount HL-X I put a thin o-ring in the grooves on the light head to snug up the fit
I'm made this scan to model a mount and thought someone else might find it useful.
I wanted a red filter for my Streamlight Wedge flashlight for some nighttime use. Could also be made in different colors. I made this one using American Filament Ruby Red transparent PCTG.
Streamlight TLR 4 A Key Picatinny Rail Adapter If you need it, you need it.
Flashlight holder for a Streamlight Stinger flashlight. Tested to fit with the Stinger DS, though looks like it should fit other variants. Made to fit into the Ford FITS system slot located on the back of the center console in a Ford…
Lets you use streamlight TLR7 family (e.g. hlx) on the JL Billet Reaper RXM (original/compact) chassis. Use the 1913-3 key Mirror the part in your slicer for the right switch Two models available, both work with the holster: The standard…
This is a Lens Cap for the Streamlight ProTac 2.0 Rifle Light I put a thin o-ring in the grooves on the light head to snug up the fit.
This is a Lens Cap for the Streamlight TLR-1 HL This may also fit the Braun - 1000 Lumen Rail Mount LED Light (This cap fits my Braun light, but is slightly loose)
Hello! I used the following designs to create this mount: CR-10 Streamlight Microstream Holster by i_need_a_better_name on Thingiverse SKADIS Universal Hook - base and modified hooks by galvanization I printed at 100% infill in PLA with…
