2234 modeli
I designed this model to squeeze a bit more performance out of the Thermalright AXP90-x47 CPU cooler in the FormD T1 v2 case. The duct prevents re-circulation and ingestion of hot air into the cooler and can provide some passive cooling…
Wydruk około 1,17 €–1,43 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Plastic cover replacement for the jacking point hole in the side skirt of a Ford Fiesta MK6 ST150/XR4 2004-2008. There is one version for front right (FINIS 1354162) and one for front left (FINIS 1354166). It is not an exact replica but a…
Wydruk około 12,07 €–14,75 € nettoWstępna wycena jednego wariantu
Make Your Own Custom Charing Station using these 3D Printed clips Go have a look at your current charging setup now, I bet the wires are all tangled! I have included designs for a basic charger station that has cable channels on the back.…
Wydruk około 2,80 €–3,42 € nettoWstępna wycena jednego wariantu
Made two mount plates, one flat and one with slots for landing skids/wheels. The landing legs have 2.5mm hole which I tap to M3 thread and use a M3x8mm screw. A rubber band is used to angle the skids up ~15 degrees during flight. The rear…
Wydruk około 0,38 €–0,46 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Compatible with the original CFT1 v1, Half Upgrade, and the v2. Use v2 models for Half Upgrade and v2 radio. The v1 case provides a slightly more compact case for the original CFT1 but will not work with the Half Upgrade or v2. The v2…
Wydruk około 2,29 €–2,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I wanted to make better use of my Dremel Drill Press workstation for other pressing tasks without compromising stock utility. The system consists of a dummy rotary tool head that mates with the press and will then accept future…
Wydruk około 6,99 €–8,54 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Simple mount for my UNI-T UT139S multimeter to Parkside pegboard. It should fit on all other models from UT139 series. Easy print, no supports needed. PETG and 3 perimeters recommended. Attach with two M5x8 screws from behind.
Wydruk około 2,84 €–3,47 € nettoWstępna wycena dla PETGMateriał u źródła: PET
⚠️ Disclaimer: this project is coming in contact with 220V electricity. Be careful when doing any changes to your power outlets (because you or others may die). Old Swiss sockets do truly badly when supporting a plug. This is a…
Wydruk około 1,38 €–1,69 € nettoWstępna wycena jednego wariantu
Connect BOSCH PEX400AE to FESTOOL CT17 44mm vacuum hose. Self locking on sander.
Wydruk około 2,66 €–3,25 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The CFT1 is an excellent field radio, but sometimes we want to use it at home or more casually. This allows you to place your radio in a tilted position perfect for operating. You can even use it for tabletop POTA activation, though I…
Wydruk około 2,44 €–2,98 € nettoWstępna wycena dla PETGMateriał u źródła: PET
With layer high 0.25 --> Layer 16.45, stop for insert the Hex nut M5. I had to change all my socket T15 with a CEE socket, but the CEE is bigger than the T15. So i made this adapter. T15 (Screw hole 38x38 M3-M4) CEE (Screw hole 60x60 M5)
Wydruk około 1,97 €–2,40 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The Contraption is a 3D printed case that combines a radio, battery and antenna into a single setup. Mike and Becky over at Ham Radio Duo have created a version for the QMX, and I have made a version for the CFT1, which effectively turns…
Wydruk około 5,64 €–6,90 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Backplate with switch cutout for the MeshNRW Heltec T114 Case
Wydruk około 0,47 €–0,57 € nettoWstępna wycena jednego wariantu
Das Model dient als Ersatzteil. Mein Controller fiel mir runter und der Hebel brach ab. Er lässt sich am besten mit dem Teil das später den Finger berührt auf dem Bett drucken. Wer mehrfarbig oder Multi Material drucken kann, kann den…
Wydruk około 0,25 €–0,30 € nettoWstępna wycena jednego wariantu
DeskPi RackMate T1 RGB LED Bar clip Fits a 3PIN Led Strip Rigid Bar 33cm https://s.click.aliexpress.com/e/_mtBJoC5 which can be controled using WLED. One is enough to hold the LED bar.
Wydruk około 0,21 €–0,25 € nettoWstępna wycena jednego wariantu
Imprimer en vase spirale sans couche solide dessus et sans couche solide dessous. Imprimé en PLA : bonne durabilité. Monter simplement en serre sur les pneus d'origine, si le montage est difficile utiliser du produit vaisselle.
Wydruk około 0,13 €–0,16 € nettoWstępna wycena jednego wariantu
this makes pulling insulin easier for vials. i recommend printing it on the side
Wydruk około 1,16 €–1,41 € nettoWstępna wycena jednego wariantu
A GPS enabled Meshtastic® case for the Heltec T114 board with GPS module. Install the buttons, board, GPS module, SMA Pigtail and snap the 2 halves of the case together. Secure with a M3 screw for a rock solid enclosure. License and Fair…
- IF YOU JUST BOUGHT a PARTS KIT from KB-3D.com → please go to the following download page for the MK6 : Fun Size KB-3D Build Kit : https://www.printables.com/model/1246713-the-recreator-3d-mk6-fun-size-a-kb-3dcom-build-kit If you are…
Summary This is a model of a VW T1 Bus “Samba” in a kit / gift card style. Some characteristic details can be discovered. After printing, the model can be assembled with the help of integrated connectors. The wheels can be turned, but the…
***BENDER2 WITH HELTEC V4 SUPPORT, GPS SUPPORT AND 4x 18650 BATTERY SUPPORT IS AVAILABLE FROM MY WEBSITE HERE *** Bender is a 3D printable case for the Heltec V3 and Heltec T114 LoRA Meshtastic powered Radio node. It features a bay for an…
If you intend to sell prints of this model, then please purchase a Commercial Use license version here . Main Features: - Improves thermals - Reduces fan turbulence by using circular cutouts for the fans - Easier fan mounting or swapping…
Tool mount and dust shoe for the Makita 700 series palm router or the Sienci AutoSpin T1 and a 70mm OD or less vac hose. PETG or better if you are concerned with heat. PLA works for most routers, some new ones seem to be hotter than the…
Commercial Use and Attribution Notice: Alley Chat HT114 Pocket Pro © 2025 by Alley Cat and Majestic AV, LLC. is licensed under CC BY-SA 4.0 . Commercial use of this design, including promotional use, selling, and reselling to other…
Recreator3D.com – Turning PET1 Bottles into Filament with Repurposed 3D Printers We’re not just recycling—we’re recreating . At Recreator3D.com , we’re transforming PET1 plastic bottles into high-quality 3D printing filament using…
I designed a series of honeycomb-style keychains featuring various car brand logos. Each keychain combines a lightweight and modern honeycomb pattern with the distinctive emblem of the chosen car brand. The design is both stylish and…
A box I remixed for my multimeter. The lightning bolt was just a random .SVG I found and put in bambuslicer. Will require 6x M3x20mm screws for the hinges and latches. I super glued the insert in so it stays in place. I printed mine out…
NOW UPDATED WITH SIMPLER UNIVERSAL POWER SWITCH DESIGN INTRODUCED IN BENDER2 Bender's bigger, badder brother is here! Meet Flexo, the most flexible Meshtastic powered node "case kit" available… and its FREE to print! Check out the intro…
HOW TO INSTALL PROFILES NEW UPDATE 22.11.25 Petg-hs profile added. NEW UPDATE V1.5.1 19/08-25 - First layer fan turned off, Gcode for bed mesh profile have been added NEW UPDATE V1.5.3 26.09.25 - Changes to support settings, Zhop and…
Designed to fit inside a 20 mm hole drilled into a wooden door, with a matching recessed magnet in the door frame. Once installed, the sensor is completely hidden while retaining the reliability, battery life, and Zigbee support of the…
Introduction The Dakar rally is an over two week long endurance race with a total length of up to 8000km. Introduced in 2022, the Hilux T1+ is a purpose-built rally truck built for the Dakar rally. By 2025 it has certainly proven itself,…
***NIBBLER2 WITH HELTEC V4 SUPPORT AND A POWER SWTICH IS AVAILABLE FROM MY WEBSITE HERE *** Say hello to Nibbler, the tiny HeltecV3 or Heltec T114 “pocket” Meshtastic powered node. THESE PRINT FILES INCLUDE BOTH VARIANTS OF NIBBLER,…
DHT11 Sensor Case for AZ-Delivery DHT11 Optional bottom piece with mounting hole included. The two pieces are meant to be clued together. I'm currently working on snap-together pieces. Feel free to remix. Tolerances for the top piece are…
VW T1 Bus Pickup Pen / Desk Organizer USB SD microsd
Change log 2025/01/01 Added STEP and Fusion 360 source files. 2025/12/08 Added v10, only change is 5mm taller walls NOT for commercial use, if you want to sell these please get in touch. The charging cradle/puck prints with no supports…
Commercial Use and Attribution Notice: Alley Chat HT114 Slim Pro © 2024 by Alley Cat and Majestic AV, LLC. is licensed under CC BY-SA 4.0 . Commercial use of this design, including promotional use, selling, and reselling to other…
Other requirements: 1. Gearbox (would be ideal but could also be used in a different way) 2. cylinder with no holes. 3. arduino or other fire control unit . (will work without it, just not efficiently at all.) 4. Air valve (I used one off…
I remodelt the original design to use it as an money box for an for a non-profit citizen bus in my town. The money box is screwd to the bottom with 4x M3 screws. The roof mused be glued to the body. The size of the model is routhley…
Desk mount for a Thrustmaster T16000M HOTAS. This design will lock the mount in a forward position, so it's best placed either in front of you, or closely off to the side. This assembly is not entirely customizable like other models…
Created from raw in Solidworks with Air flow simulation test included. Inlet airflow is not affected, but also improved. Silencer has inside some chambers that broke the sound signal, just like exhaust silencers. Reduce intake sound,…
If you need to buy the tracker: Seeed Studio SenseCAP Card Tracker T1000-E Make sure to use coupon code B737HUW8 for 10% off. Commercial Use and Attribution Notice: Alley Chat T1000 Holster © 2024 by Alley Cat and Majestic AV, LLC. is…
STOP!!! If you don't choose to participate in what is considered a BETA print. Follow this link to known working files. https://www.printables.com/model/179820-the-recreator-3d-mk5kit-ender3-diy-3d-printer-fila BELOW …is the BETA Step…
Introduction With this adapter, you can hard-mount your Thrustmaster TMX or T150 steering wheel (T128, T248, T-GT II, T300, TX, TS, T500, 458, T80 models as well). It's quite an upgrade from the OEM clamp-style racing-fixation-kit-fk2…
The Recreator3D.com –MK6 : FUN SIZE - a KB-3D.com Build Kit Experience - Turning PET1 Bottles into Filament! BUY A KIT HERE!!! 🚀 KB-3D's Impact on the MK6 Kits Since 3DPrintopia 2024 , KB-3D has helped take the Recreator3D MK6 from a DIY…
What's this? As seen in my FormD T1 v2.1 video , this anti-sag bracket secures the 4080 or 4090 Founders Edition stock air cooler and eliminates sag. Configurations supported: 3 slot 3.25 slot 3.25/3 slot (top strut in 3.25 slot + 5mm…
I made this for the NeedItMakeIt fan duct contest and it won! It's a lightweight high performance fan duct for the FLSUN T1. This was a first attempt at a fan duct (for a printer that I don't even own lol) so I'm pleased with the results.…
For parts like the nacelles just mirror the parts in your slicer to get both sides. Hardware used: -Matek H743 Wlite -Matek m8n gps -Iflight Xing2 1806 2500kv motors -Corona DS939MG servos on tilt, Racestar DS5601MG servo on elevator…
Commercial Use and Attribution Notice: Alley Chat HT114 Slim Pro © 2024 by Alley Cat and Majestic AV, LLC. is licensed under CC BY-SA 4.0 . Commercial use of this design, including promotional use, selling, and reselling to other…
French mailbox PTT T10 key. Print as it is, 0.2mm layers, with automtic tree supports. Be sure to remove all supports.
These are covers designed to plug the holes at the back of the FormD T1 case. I've prepared two different designs. Print Settings: Material: PETG Layer height: 0.20mm Supports: no Perimeters: 2
Inspired by some of the battery-powered soldering stations already out there ( particularly Callingall's ), I created my own version from the ground up. INSTRUCTIONS : Click here. Includes info on parts required, how to print, and how to…
Made the bottom case a bit bigger to accommodate an 2000mAh battery and widened the screw hole to allow for a threaded insert and changed the front and buttons to allow for the insertion of the Heltec T114 with its protective plastic…
Commercial Use and Attribution Notice: Alley Chat HT114 Pocket © 2025 by Alley Cat and Majestic AV, LLC. is licensed under CC BY-SA 4.0 . Commercial use of this design, including promotional use, selling, and reselling to other businesses…
18/09/2025: I have some of these complete and ready to go on eBay if anyone is interested: eBay Listing Update 18/08/2025: Made some slight changes to the front case, giving the battery pack a little more room, approximately 1.5mm of…
Developed by BAE Systems, the Hawk was initially developed as a light sub-sonic trainer jet for the RAF, but is found worldwide used by many nations either as a trainer or low cost light combat aircraft. Used as the primary aircraft for…
I based it on the style of the holsters for my Alley Chat HT Pocket, and I think it goes really well with the H2T design. Baofeng Belt Clip Generic Belt Clip Heat Set Inserts This is a new work completely owned by myself, but I am…
The newest V2.1 version of the FormD T1 case switched from threaded M19 holes to smooth. I found the existing plug model did not have an interference fit with the smooth M19 holes and made my own model of the plugs.
Introduction: This is a 3D printable scale model of VW T1 , designed for easy 3D Printing and Assembly. Inspired by the iconic van, the model tries to captures the timeless shape and character of the original while keeping the design…
A universal adapter for the X20V Parkide tool battery with an addon for connecting a Pinecil or T100 style soldering iron. The adapter can be used to attach your own addon. I included a step file for remixing the designs to your own…
This is my rendition of a case with lid for the ESP32 S2 NodeMCU board to house the DHT11 temperature and humidity sensor. This model also have the Home Assistant logo embedded on the side. This simple design ensures a tight fit for the…
Dyson Mini Turbo 967479-01 96747901 belt housing part T112750 supports needed This part was broken when the mini turbo brush of my Dyson V9 started to rattle I printed it in PLA and after a year it is still going strong Category:…
Need it printed? If you want the printed part, please purchase it from LinkGear :-) A solid mount solution for your AXT1800 / Slate AX! This design allows you to easily wall-mount the AXT1800/Slate AX to a plate/wall or whatever you like.…
1:48 ORIGINAL SCALE ▪▪▪▪▪ 18 PARTS ▪▪▪▪▪ 39 X 88 X 41 MM ▪▪▪▪▪ STL FILES ONLY ▪▪▪▪▪ ❌UNSUPPORTED FREE EDITION — a free simplified and smaller version of the complete model based on LEGACY EDITION (see the comparison table in the picture).…
This is an enclosure for a DHT11 sensor module. The Sensor/PCB is held inside the case body by the post, and the lid is secured to the body using a flat or pan head M2x3 screw through the same post. Print Settings Printer Brand: Prusa…
I've included a Reverse Model for use with some 3rd party chargers. Fusion 360 File included!
Spliced together a few different files to fit my own requirements. You may need to re-size/check the carrier dimensions depending on your own ESP32 board. I designed this to use with Jumper cables, i didn't have a screw for the DHT sensor…
Introduction The weak link in the less expensive Thrustmaster steering wheels is the plastic gear and optical timing wheel. Over time it can wear out and with enough force, it can strip teeth. I was inspired by the Thingiverse models…
Tikka T1x Cheek Riser. Mount with 2 sided tape.
Update 25 October 2025: I have uploaded a step file of the standard back plate for your adjustments and ideas. Since the adhesive version of the back plates of the Xiaomi Aqara temperature / humidity / pressure or vibration sensors…
2025/02/03 Added STEP file A collection of cases, frames or holders for the Seeed Studio SenseCap T1000-E. Any ideas welcome, please add your suggestion in the comments. Printing info (I use Orca Slicer 2.2.0): up right no supports needed…
This design serves as the basis for designing and printing a speaker mount for a speaker with FlexMount165 or 200 technology. Open the step file in a CAD program and construct tabs at the points where screw connection points are required.…
This is not my design. It's a joystick remix of a gimbal designed by user Karavan on IL-2 Sturmovik forum: https://forum.il2sturmovik.ru/topic/13252-3d-печатная-механика-объект-77-б/ and shared on Thingiverse and v2 on Thangs. Images and…
There were a few errors with the meshes so parts were becoming separated and broken, they don't now. Also they are STL now instead of 3MF.
This is a replacement cap for a super stroke grip for a golf putter. Also included is a version of the cap which can be printed in TPU and used with a Garmin CT10 club sensor. Normally this sensor simply screws into the end of the club…
I once ordered a set of 10 different T12 soldering tips (from here or here ) and had them laying around since then. So the idea came up to design this stand and optional cover for it. Prints without support. Also the cover! It's…
As seen in my YouTube video: The Ultimate FormD T1 Air Cooled Build Panels require a large print bed (300mm+) and a well calibrated printer. They are somewhat experimental, trial and error may be necessary to get satisfactory results. The…
Print 0.2mm layer height. No supports are needed. 10% infill.
Didn't find anything acceptable and made my own version of comfort strap Printed from TPU 60D Print settings perimeters - 4/5 top/bottom layers - 0 fill pattern - honeycombs 30%
Neue Aufmachung des plätzchenaustecher VW T1 der oben offen ist.
Tikka T1x is a great rimfire rifle, but the bolt handle is slick and small. When I run bolt faster - my fingers tend to slip off the handle from time to time. I designed a knob that fits on top of the stock bolt handle and allows a better…
This is a dashboard switch-hole cover plate for various older Toyota trucks and SUVs. The original came from the other thingi site, item number 2446920 by bgsteveg . I improved it by adding some gussets to keep the tabs from cracking off.…
The Fuji X-T10, X-T20 and X-T30 are great little cameras, but the grip is a bit small for larger hands: your pinkie has no-where to go except under the camera. This newly updated grip provides full support for all of your fingers, yet…
Halfway through the print pause your printer and add 1-2 small spit shot weights to make the rattle inside. Once printing complete add three small split rings and two treble hooks. Happy catching!
Simple mobile/pocket enclosure for a Heltec T114 board with an 18650 battery. Most models place the battery behind the board, resulting in a bulky enclosure. This is about as compact as possible. Assembles with eight M3 heatset inserts…
This remix extends the mounting surface by ~10mm to make room for Ego trimmers with an adjustable handle like the ST1510T. The older style trimmers still fit, but have bit of room to slide back and forth. I printed mine in Polymaker…
Easily printable extender for Quicko T12 microsolder and its other clones of the same size, which allows this microsolder to be elegantly operated on batteries designed for Makita or Parkside hand cordless tools, which is useful not only…
This is a case for the Heltec T114 v2 with MakerFocus 3000mAh battery. Designed for the use as a Meshtastic or Meshcore node. Before you start: This model has very small tolerances - Accurate printing required. If you are unsure, scale it…
This allows you to put the ASUS ZenWiFi Pro ET12 on the wall. It is designed for the ET12 to drop into the wall mount and the ET12 will not move around. There is enough space in the back for cables. Print Instructions: Print strong in…
Remixed from VZPHOTOs Fuji X100V Thumbgrip. For XT20, I needed it to be a little longer so here it is.
Plugs the arbor hole that spews dust everywhere. This is a loose fit meant for easy install and removal: 1. Insert the tab on the left. 2. Line up the tabs on the top and bottom. 3. Mallet time! (on the right) Print in PETG so it'll be…
Multi Toolholder for Skadis and HSW (drill/bit/allen) In this download you will find two Versions. One for IKEA Skadis, and one for the HSW Honeycombe This Toolholder will give you 19 slots for Drills (1mm-10mm 0.5 steps) 31 slots for hex…
The Dell T160 is too new (in 2025) to buy spare parts for it, and so, we cannot buy the Dell T5CVH part, which is the 2.5" tool-less non-hot-swap caddy for this server. It's sold with drive only by Dell. So I created this model from…
Schlüsselanhänger ist mit Materialwechsel zu drucken. Keycheain is to be printed with material changes. Schichtdicke 0,10mm / Layer 0.10mm Infill 100 % color change 1,10 → 1,80 → end
Oktober 2024: Version 18 mit detaillierteren Tritten. August 2024: Version 17 - neues Gehäuse und Dummy-Chasis für TTm hinzugefügt. Nehmt die Teile mit den höchsten Versionsnummer. Die Fenster wurden nicht neu exportiert, daher mit…
VW T1, reduced to a small, clean object that keeps its main shape and character. Part of the Mini Cars collection — The model is simplified for a reliable print at a very small scale. Print tip: use a 0.2 mm nozzle for better detail.…
Printable Replacement Motor Mounts for the Heewing Ranger T1. Credit to @AlexSalut. These are really nicely designed replacements for the stock motor mounts that will allow some larger motors. I'm using T-Motor F1507s in the attached…
This is a custom box for Lamy T10 ink refill cartridges. There are two versions, one for 5 cartridges and another one for 9. They have an opening on the cover, so you can quickly check how many cartridges are left and which colors they…
Hi Internet Sim Peeps, At request, I've whipped up a TMX/T150 to stock Thrustmaster Quick Release hub adaptor. Now, I want to preface this with the fact that I don't have a TMX or T150. I've used reference images and materials to gather…
Own a piece of motorsport history with this 3D printable STL model of the Mercedes CLK GTR. This legendary GT1 race car model is perfect for motorsport enthusiasts and collectors of iconic racing machines, showcasing aggressive…
This is a case for the Heltec Vision Master T190 for Nerdminer Bitcoin Mining. Has a 30mm Case fan that can be powered from the board adapter itself. Also a pedestal to allow better stability on a desk. Design allows multiple devices to…
