Liczymy pasujące modele…
Printing parameters: Resolution: 0.2 mm Perimeters: 4 Infill: 15% Supports: no Brim: recommended Assembly: Add some corc, rubber or foam at the bottom of the block. When you clamp in sand paper, the blocks will be fixed. Review: Related…
Print resolution: 0,05 Supports: NO Rafts: NO Material: PLA
Don't forget to hit the like button if this helps you :) A perfect calibration square print has alluded me since I got my Ender3S1. Sure I have lots of prints that work but most of them are smaller and around the center of the plate. If I…
READ INSTRUCTIONS: I see a lot of the prints and you guys area printing it in the wrong orientation. It's much stronger if you print it with the Holder orientated how it would be when you use it. UPDATE: Added Glock 43x Needed a place to…
Small surface mount box, for hiding cables and wago connectors 2024.02.20 - I added a model with a slightly lower housing
Introduction/Support Me: If this 3D design helps you optimize your PC's cooling, please consider hitting "Like" on this model file! Your support encourages future designs. You can also support my work by purchasing items for this setup…
This is a 3x4 gridfinity usb cable organzier for 12 x cables . The diameter per cable is approx. 12mm. Have fun and don't forget to post your makes :-) Check out my other designs and follow me for more.
Collection of screws (ISO 4762 / DIN 912) including : M3x 6, 8, 10, 12, 16, 20, 25, 30 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I would recommend…
This is a recreation of https://www.prusaprinters.org/prints/36706-bed-level-test . I didn't like their instructions and the dimensions of the model, so I made my own. Print instructions Select the STL based on your desired layer height.
It works on OEM and S15 mags. I take no liability as this was just a fun project and should be a stepping stone for anyone that is considering a magwell.
HalfManBear's shroud design but with multiple optimizations delivered in one package Thanks to Layer.Shifted for pointing out the airflow problems! Special thanks to @mcbabo for making the assembly illustration! 🤩 Do you like the design?…
Collection of screws (ISO 4017 / DIN 933) including : M3x 6, 8, 10, 12, 14, 16, 20, 22, 25, 30 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I would…
Do pobrania moja wersja powiększonej baterii 3x względem oryginału do Parkside X20V Team, wzorowałem się na wersji dostępnej poniżej jednak samą obudowę zrobiłem od nowa wykorzystałem jedynie wsad na ogniwa 3x… Oryginalne źródło:…
Update (08.12.2023): I reworked these models to meet the correct Gridfinity Specs. I based the first version on this model: https://www.printables.com/de/model/399759-actually-parametric-gridfinity-base-grid-bins , which sadly does not…
display for your 1/64 diecast cars, remixed I really liked the model by aonarcan. while slicing I noticed that the first layer could be better. I noticed the bridging that is unnecessary there. after I modified the model this problem is…
What's more fun then 4 keys? 9 keys! Designed to be compatible with Cherry MX style key switches. Just add 9 of those, some key caps, and a lanyard. It's recommended to use XDA form factor key caps, but others should work also! The only…
Tested and printed without issues using Cura slicer. 1 : 7 → 1 : 8 = 87,5 % Multiple scales are in ZIP files (1/18, 1/12, 1/7), download whatever you like. Picture with recommended print orientation of parts is included in ZIP (but it's…
Small surface mount box, for hiding cables and wago connectors
Box for hepa filter and activated carbon pellets for the Creality K2 The K2 Plus already has a carbon filter installed, but it is only partially filled. I also wanted to have a hepa filter on the housing and came up with this design.…
Classic three-dimensional solid puzzle. Seven unique shapes combine into a simple cube. And there's more than one solution. Print and gift this fascinating puzzle game to your familly and frinds. Great for ages 8 and up. Print also…
In Line Wago 221 Junction Box, perfect for splitting 1 wire to 2 wires. Compact design
Simple Gridfinity bin. The name of the objects are the dimensions, for x and y and the height. The height is a multiple of 7mm: 2 = 14mm 3 = 21mm 4 = 28mm 6 = 42mm The x and y are multiples of 42mm: 1 = 42mm 2 = 84mm 3 = 126mm 4 = 168mm…
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: outer_diameter = 14 thread_step = .5…
I made these 120 film cases and thought I'd share them with you. There are two variants with space for 3 or 5 rolls. Both the container and lid are chamfered to avoid an elephant foot. The tolerances for the lid have been tested and…
Simple Gridfinity bin. The name of the objects are the dimensions, for x and y and the height. The height is a multiple of 7mm: 2 = 14mm 3 = 21mm 4 = 28mm 6 = 42mm The x and y are multiples of 42mm: 1 = 42mm 2 = 84mm 3 = 126mm 4 = 168mm…
I really like this simple 3x3 Calibration. But it takes too long and needs too much material. So I created a smaller one :) It is designed for my MK3s but you can easily skale it depending on your requirements. Because every area is…
For longer bits use this: https://www.printables.com/model/579292-gridfinity-bit-holder-1x1-long-bits
Mounting for Voidstar Labs' Gridfinity containers on pegboards without wiggle? Heck yeah! This model uses my locking pegboard mount system for 1" standard pegboards. Magnet holes (if present) are designed for 10mm diameter, 3mm thick…
Updated 5/29/2023 - Redesigned to clean up the model and add PS4 and Tribute64 controller compatibility, and replaced one of the AA battery spots with a space for a USB dongle. Gridfinity-compatible 3x4 storage block for Xbox One, PS4,…
Print Settings Layer Height: 0.2 Flat Top vs. Angled Top The flat top version has nicer lettering and is more neat, but one might prefer an angled top to avoid damaging wallpaper.
This piece replaces the factory Barrel Plug of a Safariland 63xx Glock 17 Holster to make it fit 19 and 45 Models. Reccommended Settings: Heat Resistent Filament 10%+ Infill 5+ Perimeters 0.1mm Layer Height Print Orientation and Supports…
Small desk organizer (1x3 Gridfinity base) to hold pens and related desk paraphernalia: mine holds a pair of scissors, a bunch of pens, nail file, box cutter, and a couple of small picks and screwdriver tools. Reorganizing my desk and…
1 Pocket Size (64mm x 71mm x 70,25mm) {xyz} You can download it in two different sizes. I printed the big tea bag with 0.4mm nozzle (0.3mm layer height; 15% infill) in PLA. Printer: Artillery Sidewinder X2 Nozzle: 0.4mm Layer height:…
Remixed bolt measuring tool remixed to fit on a Gridfinity 3x1 baseplate. Printed well on Bambulab X1 using standard PLA and 0.2mm layer height.
I made these 135 film cases and thought I'd share them. Just like my medium format (120) film cases, these come also as a 3 and 5 roll size option. The lid is symmetrical so it fits in either orientation and the registration pins hold it…
Simple little plug for the grip of the Glock 43x. Not much to it. Just follow the instructions. How Too. Print, in PETG, but pay attention to the way it sits on the print table in your slicers. You must help it. Look at photo. It should…
Print in upright position, no supports needed. Holes are designed slightly undersized so before assembly, drill through holes with 4mm drill. Designed for M4x30 bolt and M4 nut. 1/8 inch imperial hardware should work as well.
PCB standoffs. For best results use .05mm layer height for threads. this will give you 10 layers per thread and should result in good performance. Please let me know if you find them useful. 12 mm standoffs with M3x0.5 threads. 3-10-19 -…
A hex/drill bit holder for Gridfinity that holds 4 rows of 10x 6.5mm hex bits. Each hole has a 0.5mm tolerance so the bits fit securely and can't rotate, but can easily be pulled out. I've left space below each row to print out labels.…
Hello, This is a nice mashup of the Parametric Gridfinity base plate by @Cunfusu and the Rugged Box by @Whity . Enjoy! Also pictured is my Gridfinity Bambu Nozzle part https://than.gs/m/842099 EDIT: Added a model to be printed in TPU to…
This Gridfinity storage block is designed to hold a Dymo LetraTag label maker and up to 6 extra label tapes. It is designed to fit into the top drawer of an IKEA ALEX drawer unit while fully loaded. Based on and compatible with Zack…
Gridfinity 3x1 Bin with three slots for gift, credit, or business cards, including a shallow tray for small objects. Can be printed without supports.
This is inspired by the dozens of horizontal plier racks for gridfinity. This design has the following improvements: Wider slots (6 in a 3x vs 7) Shorter at 4x vs 5x Top lip which holds spring loaded pliers and nippers in a more compact…
Remix from zx82net Great Rugged Box. The latch and hinge are not change so you can use all of his different models. Ammo box for 50pcs x 9,3x62 Printed with Extrudr MF Military Green PETG and Prusament Jet Black PETG 0,30mm 4 Layers. Hope…
Update - 2/20/2026: If you care about the future of 3D printing… Please inform yourself about the legislation which is currently being considered in Washington, California, New York and Colorado, and will restrict and regulate 3D…
If you like what i do, please consider throwing a few breadcrumbs my way :) https://ko-fi.com/duckers
Ever wanted to destroy the world? Well HERE YOU GO ! Now you can print your very own building tools and uhhh, WREAK HAVOC! *JK! This won't actually destroy the world, but it's a neat thing to print. Inspired off a meme that I saw
This is a 3d printable Magazines for the Tikka T3X Tac A1, CTR and Arctic rifles. Included are models for a 5 rnd and a 10 rnd version (with the 5 round variant being the more practical choice) which are a dircet replacement for…
This remix of the "Skadis continuous shelf" is wider and deeper. Its 223mm wide and 160mm deep.
Small surface mount box, for hiding cables and wago connectors - just shorter Please use low-current sensor and signal wires only . It is not suitable for mains wiring due to potential safety risks and regulatory non-compliance.…
Collection of screws (ISO 10642 / DIN 7991) including : M3x 5, 6, 8, 10, 12, 16, 20, 22, 25, 30 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I would…
Put a gridfinity base on Muzz64's glasses stand from https://www.thingiverse.com/thing:1264885, and boom, we've got gridfinityglasses. Holds three relatively standard/shallow frames, so it works for my readers, gunnars, and sunglasses;…
A simple remodel, I did not take my time, but I spaced it out a bit to support 5 3.5" drives instead of 4 like the original model. I have computers that use the IcyDock FatCage, which supports 5 3.5" drives. I found this model when…
I needed this awesome case to hold 3, 1x1 Gridfinity bins, so I sliced-n-diced bnorick (https://www.printables.com/social/187921-bnorick)'s Fusion360 project, which is, itself, a slice-n-dice of JamesThePrinter…
Update (--> for Breacher & Battle Axe) --------------------------------------------- Silly Shell with 3x airtight Elite barrels 6x Short Darts / 3x Elite Darts / 18 caliber .50 foam balls Update 30.9.2025: Modified shell, suitable for…
Gedruckt aus PLA. PETG, ASA und andere, nicht Flexible Materialien Funktionieren aber auch. Mit mindestens 3 Wandlinen Drucken! Stützen sind nicht nötig. Fusion360-Datei angehängt, somit habt ihr freien Spielraum bei der Anpassung der…
it is largely based on Foden's design , which it also fits together with. I have also made a model for the Unifi Switch Ultra (USW-Ultra)
Remix von https://www.thingiverse.com/thing:4599572 Schriftzug auf BMW abgeändert. Erweiterung bzw. Austauschteil für den Original Schieber am Wireless Charger. Passend auch für F3x, F8x und I01 (I3) mit Wireless Charging Ablage. Die…
Don't forget to hit the like button if this helps you :) Improved calibration prints with minor modification to connect all the printed squares for easy removal from the bed. (uses a 0.4mm line width) These prints work seamlessly with the…
This speed cube is optimized for 3d printing with no supports and no glue required to assemble. Hardware required: M2 10mm Screws 6pcs 6 pen Springs (OD-3mm, Thickness-.5mm, Length-6mm) (OR) Lighter Piezo Springs We were curious to learn…
Hyte Y60 Fan Bracket (3x120), I made the second version of the https://makerworld.com/en/models/138628#profileId-151004
Thanks for Bernie sharing that great model - please like his model as well. Printed in PLA 0.2mm layer height without supports and 15% infill (10 or 5% should work as well). First put the two parts of the battery holder together then…
A custom bigger bolt knob for tikka T3X. You will need to glue in in place like the original one.
Designed for use with PLA filament, 4.5 hour print
Place on the bottom face when slicing!!! This model is easily printable without supports as long as you place it on the face of the bottom support (the hypotenuse of the right triangle) in your slicer. Put the Gridfinity organization…
Version 2 of my original Shell Caddy Designed for ELS and Tek-Lok mounting systems May fit others with 1.5" hole pitch 10° grab angle on the shell groups Added mounting options and configurations New parts work with old mounts, if you…
Part of my series of enclosures designed for Shelly smart devices and Wago 221 connectors. Shelly box for T&E 3x slots and wago 221 connectors (this one) Shelly box for inline flex wire and wago 221 connectors Shelly box for 2x flex wires…
A compact snap-on holder designed to mount three WAGO 221-415 connectors on a standard 35 mm DIN rail. Ideal for clean, tool-free installations in control cabinets, automation projects, or DIY setups. This version fits only the 5-port…
A tool I made years ago but remade now that I know how to actually CAD correctly. This is a tool helps you take the end cap off as well as ‘cock’ the striker so you can put the bolt back in your rifle since the spring inside can be rather…
Fits all the bits from this electric precision screwdriver kit . In addition it has storage on the side to hold all the various tools I use for 3D printing. I included the step file and f3d file if anyone wishes to remix/modify. From the…
A Gridfinity dual plastic razor/scraper holder. Will hold two of these plastic razers/srapers plus approx 100 additional blades. I needed this to fit into a shallow drawer and this fits perfectly. Fits a 3x1 grid and approx 47mm tall when…
Voron V0 V0.1 1515 3x Wago 221-415 Mounts 2x M3x6 SHCS and 2x M3 nuts were sufficient for me. I ordered Wago Ex instead of the regular Wagos because they're white. And they're more useful in case you printer tends to explode.
I created a fully printed mirror cube. The mechanism is designed to work with the printable core and m3 screws. Some centerpieces are too shallow to take springs, so for those, I just tightened the screws until the piece would spin freely…
Features: M3 threaded Inserts (ADXL spacing 15mm) Improved the heatbreak duct curvature for better airflow. Improved heat-break fan fitment + fan alignment (new). Improved LED PCB clearance/fitment Reinforced mounting lugs Hex Key access…
The parametric Autodesk Fusion file can be modified to fit your exact fan size. Excluding the air blocker plate, the model prints in four different pieces. STL files and hardware: Fit 80x80 mm and 120x120 mm fans. To mount the fans four…
Belt buckle quick release, Print with 80% infill for more strength in the locking tabs.
Easy to print, tought and compact construction. Nearly without supports.
ENG: Vertical stand for Lenovo USFF Tiny PCs. Works with M700q, M900q, M710q, M900q and presumably oder and newer variants like M720q and so on. As long as the PC is not thicker than 36mm. Made with Tinkercad. GER: Ständer für Lenovo USFF…
Gothic City is the largest, most modular 3D printable terrain on the market. You can create almost anything you can imagine with Tilescape 2. Check out the pics and videos from the Kickstarter here and purchase all of the components in…
Pretty straightforward AA battery storage in a gridfinity compliant box, most of the ones I had seen were small, knew I wanted to store a lot and didn't wan't to lose out on the opportunity for storage in the seams. Thus was born the 3x3.
I created this stand to organize handguns for storage in my safe. It is a prong-type stand, meaning that a prong is inserted into the barrel of each firearm for support. Prongs are sized for 9mm pistols. So far I have found that strength…
Another gridfinity hex bit holder. This one holds 136 bits in a 3x2 footprint. Holes are 7mm diameter to comfortably fit standard ¼" (6.35mm) hex bits.
Gridfinity Divided Bin 2x3x3 2 Large 4 Small Sections.
Replacement for battery Box. No soldering or rewiring needed, just reuse the electronics from your broken box. fits the standard transparent battery boxes that come with fairy lights etc. Ersatzbox für Batteriefach für zb. Lichterketten…
I grew tired of having my wobble sockets roll around in my tool box, so I created a 3x6 gridfinity tray to keep them in place. The tray is tall enough to keep pieces securely in place on a tool cart, but shallow enough to fit in the 35mm…
These are the latest version (v 2.2) of my lidded Gridfiniy bins, with several improvements over the 1st version. These include the following improvements and new elements: Fully redesigned bins with a more efficient use of material…
Gridfinity bin designed to hold 28 AA batteries. Bin size is 2x3x4.
Update (09.12.2023): I reworked this models to meet the correct Gridfinity Specs. I based the first version on this model: https://www.printables.com/de/model/399759-actually-parametric-gridfinity-base-grid-bins , which sadly does not use…
This is another model to expand the collection of flagazines from DeWZ.
I adapted (pun intended) this model to reduce plastic requirements and improve airflow, as SSD don't move anyway. Pick your poison: I'm bestowing you with 3 variants to feel the thrill of overloading your case with more-than-intended…
AK47/AK74/AR MAG 3X wallmount Bed organic supports recommended 0,2 layers
Redesign of a Wago mount (from Voron) with embossed labels for my RatRig V-Core-3. It has two countersunk holes 55mm apart for fixing it to Voron's really cool printable DIN clips. I have included the STEP and F3D files so you can modify…
This adapter is for flash light pewered with 3 pcs of AAA batteries. These torches are cheap and quite common, but problematic and not economical to power. You need three batteries, but they sels in packs of four. If you replace primary…
Držák WAGO svorek 3x 5W na DIN lištu. Velikost WAGO cca 30x10x18.5mm. Koukněte i na mé další modely . Pokud mě chcete podpořit, můžete zde: PayPal , BuyMeACofee , QRCode . Děkuji
I corrected the mirrored logo on the right side. The logo insert is in a separate file now. I made versions for 2, 3 and 4 tubes. Many thanks to Luis for that great model! 👍
