75 modeli
This is replacement parts of headband (plastic portion only) for AKG K7XX variants, and that transparent plastic attached to inner slider. The models themselves are flat, you need to print them with PETG or other flexible/ductile…
I designed this part to add a jack to my AKG K240 Monitor headphones without permanently modifying them. The part replaces one of the existing pieces on the headphones and holds a 3.5mm jack from Adafruit…
This is a fix for the elastic bands in AKG K701, K702, K712, and AKG K7XX headphones. It's been tested on the K712 Pro and should work for similar models. You'll need an elastic hair tie and glue for installation. If you want to you can…
Note: it works better if you print it with flex material.
I printed it in PLA at 0.2mm and 20% infill and it works just fine
For the parts with a thread in them - microphone stand mount, the screw for it and the basket (has a thread for the AKG 120 microphone inside) set as low layer height as possible, I used 0.1mm. Instead of the 3D printed screw you can use…
This is a simple recreation of the plastic rings on the bottom of the standard earpads used with the AKG 701 (and other compatible ones). It will allow you to test many 3rd party earpads (standard 100 mm ones) and see which one works best…
This is a clip in bracket to replace the worn out elastic for an AKG K7xx (701/702/712/others) series headphone. Requires no disassembly, modification, cutting, gluing, etc. It is designed for a hair elastic (ponytail elastic) of about…
This might not be the most beautiful reverse engineering but it saved my AKG headphones from the landfill. If the this piece of your AKG headphones has broken, this will fix it.
AKG K701/K702 replacement "cover 3" part. In case you broke it while repairing your elastics. Replacement for AKG part number 2458Z46060 or 5023314 (see explosion diagram from AKG ). Category: Parts
This part allows you to add a MiniXLR connector to a pair of AKG K240 Sextett headphones without permanent modification.
print on side Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Filament: Prusament PETG Category: Audio
The cat ears made by vidister on thingiverse have been remixed by ripper here on printables and I wanted to attach them to AKG 240 Headphones (or rather AKG HSC 271 headsets which are based on the same kind of headphones). So here they…
I broke my AKG K701 headphones, so I designed repair kit for them. Not perfect, but it works and looks OK. Printed with supports.
I took apart my K712's to replace the elastic band and discovered how easy it is to take off the small rounded mesh covers. I never liked how they looked -- I always wished they were flat. Now that I have a 3D printer I can fix that…
I wanted a way to add a mini xlr female connector to my Superlux hd681 headphones. There is an existing design, but it looked too fragile and does not use a mini xlr connector. This part allows you to use a 3 or 4 pin mini xlr. I need to…
This is to repair part 2040M0209 (and maybe 2040M0210) of AKG K240. It tends to break after some time. Print in PETG or ABS. No supports needed. Holes require minor filing. Glue the 2 metal rods of the headband into place. A cutout is…
My AKG 240s are great headphones, but they have a fatal flaw – the lids on these are pretty fragile and are prone to cracking. I do tend to abuse my hardware, and from experience, official replacements are hard to come by, expensive, and…
This is a very simple model, but useful for me, because I like to leave my main microphones set up at all times. I do want to protect them from dust, so instead of a plastic bag, I think these covers look pretty classy and do the job. The…
The STEP files are probably the main files you're looking for if you want to slice this model yourself. The original headband of me Superlux HD-681 (which seems to be an AKG K240 clone by shape and possibly by function) started to show…
The bottom part contains contains a cavity for a metal disk which I had. Consider redesigning this part tobe able to accommodate some metal parts that you have to achieve more stability. Mount some screws to attach the inner/outer legs to…
Model is created for K270 but I assume it will be the same for all simillar headphones from AKG. Material needed: 2x M2.5(OD3.5mm), 4mm lenght Heat Insert 2x M2,5x14mm Flat Head Screw Assembly: Melt the Heat insert into the Top part and…
I have no clue if it is possible to print this on variety of printers as it is quite a tight fit (0.05mm on the entrance, scaling just a bit should fix it though). Could not come up with better solution for the rotating mechanism, lol.…
If you have this headphone and the part that holds the speaker on broke, then you want this.
Check out this video -> https://www.youtube.com/watch?v=8M6FCPxSxv0 That is what this part is. I printed it & it worked perfectly. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: Doesn't Matter Supports: Yes Resolution: 0.1…
fix elastic problems by using hair rubber band instead
This is a replacement cover for the AKG K240 MK-II, as the original plastic cover breaks easily. It is modeled to be as close as possible to the oginal part. Print laying flat with supports enabled.
Was getting frustrated with the modmic losing adhesion from the k7xx headphones as there was no perfect spot for it. Designed this to allow for a solid surface for the modmic to attach to. I printed mine with the pad side down. Category:…
Das Unterteil für das AKG HT4500 Mikrofon geht immer sehr schnell kaputt - vor allem wenn man es einmal zu fest zu schraubt. Deshalb habe ich das Teil nachkonstruiert. Nach einigen Versuchen hält es perfekt. Ich habe versucht die Kante am…
This is a holder to attach Fiio BTR5 or BTR15 Bluetooth amp to AKG headphones. Comes with two different attachments, one for K240 and another for K712. Those are the models I've tested this with but should fit other models with similar…
Print everything twice for a full set. You can add L and R indicators on the preferred covers with the “Add negative volume” option in your slicer if you wish. AKG shipped these with L and R on what is similar to the TopOutside model.…
Print settings Nozzle size ......................... 0.4 mm Layer height ....................... 0.2 Number of perimeters ... 2 Infill ...................................... 15% Supports ............................. enforcers only Bed…
This clip provides a friction fit stopper to replace the elastic when it fails. No replacement elastic required. Just clip on and adjust to the required position.
Here are some collars for your Yakgear parking pole that will keep your rope from sliding up and down the pole, watch the video for instructions on how to use them.. https://www.youtube.com/watch?v=80RvurEKz3c&t=37s Print Settings…
This is a variant of the cat ears from https://www.thingiverse.com/thing:32885 with the ribbon hole and the big logo removed, along with an adapter to mount them to AKG K240 or similar headphones. The mount works by hooking a hair tie…
Started using my akg headphones again, but this part broke years ago, degrading the “fit”. Could not find this part here or any other site, so uploading part i modeled. Maybe someone else will find it useful. I see no reason why it should…
You can flip model to adjust driver to ear distance, there is a slack for internal diameter(54mm) so it can be glued with hot glue and removed with ipa if needed. Earpad thickness matters, so adjust accordingly, variant on the photo…
I finally made a v2! Find it here: https://www.printables.com/model/1530929-akg-k271-studio-connector-housing-v2 This part was designed for the AKG k271 Studio headphones, not the MkII. If it does fit, please let me know and I'll update…
Stand for pop filter/Akg To support: https://www.paypal.me/AlessioCasamento Category: Audio
Perfect fit for AKG K240. You can use double sided tape (any heavy duty double sided tape should work) to attach it to a side of some peace of furniture. I attached it to a painted vertical beam of an adjustable height desk. Layer…
Detachable microphone mod for AKG K240-style headphones. Requires two PJ32A TRRS jacks and a detachable microphone, as listed below. Microphone quality is on par or even better than most gaming headsets.…
Inspired by https://www.prusaprinters.org/prints/63294-headphone-bluetooth-receiver-holder I created this holder for the Sony SBH24 Bluetooth receiver. I used M3 screws to mount the holder to the headphones. The wires can be routed into…
It is attached to the shirt with a safety pin on the other side of the shirt. Very clean look, but a bit awkward to pin on.
Unfortunately I don't have a photo of the broken band, but repair is quite straight forward: Cut the Band flush. Punch a pair of holes for the new flap. Use the clip as a reference. Mount the new flap. Secure with the clip, maybe use some…
Convert your AKG M220/K240 to bluetooth with a Taotronics TT-BR009 AptX Low Latency Bluetooth Receiver. Taotronics TT-BR009 https://www.amazon.com/TaoTronics-Bluetooth-Receiver-Hands-Free-Wireless/dp/B07BLQ47MY/ Category: Audio
I design this for my modular monitor attachment but I figure some people will find it useful. Pic is slightly different since design has change slightly to match with the table/wall mounting. The headphone holder can rotate to accommodate…
I print without supports with an 0.6mm nozzle and 0.15mm layer height, and it works fine. I find this head worn microphone really pinches around the top of my ears after even relatively short use, and with these attachments, it spreads…
Head Phone case for the AKG K451. Category: Audio
V2 version, now with chamfered screw holes and redesigned cylinder for tapping without breaking. This part was designed for the AKG k271 Studio headphones, not the MkII. If it does fit, please let me know and I'll update this here for…
less comfort less sound quality but it works Print with supports only!!
Simple print, can be done in any material, no supports. Maybe use a smapp brim if adhesion ia a thing on your printer. I suggest printing it in PETG if you want to use it more than 1 time.
Chassis Sleeve for an AKG DMS300 Microphone. (5094802-00) Sleeve has ring / indent on bottom that can be colored for mic identification. Print in your choice of materials - I printed it in ABS. Threads may require finer layer heights…
Mod Mic Mount for AKG K712 Pro You need: 2x M2x 5mm countersunk screw 2x M2 Nut 2x Washer 5mm drill Disassemble Headphone:
i remixed the original to have a wall around the magnet thing. also i changed the hole to fit m3 4mm FCHS screws which screw directly into the plastic. if you want to avoid that it will probably also work with hotglue
Chassis Sleeve for an AKG DMS300 Microphone. (5094802-00) Sleeve has ring / indent on bottom that can be colored for mic identification. Print in your choice of materials - I printed it in ABS. Threads may require finer layer heights…
i remixed the original to have a wall around the magnet thing. also i changed the hole to fit m3 4mm FCHS screws which screw directly into the plastic. if you want to avoid that it will probably also work with hotglue
I wanted a way to add a mini xlr female connector to my Superlux hd681 headphones. There is an existing design, but it looked too fragile and does not use a mini xlr connector. This part allows you to use a 3 or 4 pin mini xlr. I need to…
Just a holder for my AKG K702 headphones so they are not hanging from the elastic part. Might fit other models.
Wenn der Bügel zerbrochen ist, einfach das Teil ausdrucken und drauf stecken. Falls bei euch eine andere Stelle defekt, ist müssst ihr das Bauteil spiegeln. Die Bügel sind nicht überall gleich dick. mfg If the bracket is broken, simply…
Inevitably these little parts break and make your nice headphones uncomfortable/unusable. Buying a replacement part is possible, but shipping is usually more expensive than the part, and the part is often backordered. I've personally…
Anyone who has owned a pair of AKG 240 or similar design knows that eventually that brilliantly designed self tensioning headband eventually loses its tension and the cans afterward, sit limply aloft your head. With this design, print two…
Designed by the Digital Creations Lab of AKG school in Budapest Hungary. The magnets can be glued to the places and the pieces put on a whiteboard the way you see fit.
Do you have a clip-on microphone but not an adequate surface or object to attach to? This adapter makes your classic microphone stand with 3/8" threading a perfect place to record any instrument or voice. I recommend clipping the mic the…
Cap/Lid for the right side of the AKG 240 (mk II) headphones that I managed to break since I didn't understand that you're supposed to remove the sticker and then unscrew the lid. I had best results printing it with a brim with the…
Replacement strain relief for AKG K242HD. Print in flexible or semi-flexible material. Where the cable enters the headphones, make sure to prevent the cable from sliding back out of the headphones. You can do this by wrapping the cable…
The original headband broke a few months ago (after years of usage), but the headset is otherwise still working. Rather than buying a new one, I designed this part using the live hinge technique. Print it flat on your bed at 100% Infill…
When my AKG A-51 Type V microphone base broke, I figured I was out of luck.... And I was until I got my 3D printer. Works perfectly! Print Settings Printer: TAZ 6 Rafts: No Supports: No Resolution: .3mm layers Infill: 30% Notes: I printed…
Dual headphone holder for AKG K240 Studio mounted on NZXT 340 Source.
A simple model of a holder for IKEA Bakglad silicone spatula. Prints without supports. Designed to be glued onto the wall with a double-sided adhesive tape of your liking. Disclaimer: I do not recommend to use it with a spatula being…
See other models for my desk at https://www.printables.com/@Morbier/collections/1571699
