Liczymy pasujące modele…
Shifter knob mod. Using original screw to mount the adapter, long shaft and locking to prevent breaking and over-tighten. Long version could be sensitive against breaking above the threadline. Short version in use since a few years. Screw…
PS5 snap-on driving wheel with high tolerances. This is a PS5 controller snap-on driving wheel meant for ultimate performance. Tolerances are very tight to eliminate play and sloppiness. All parts are 3D printable, but supports are…
Update: Added a tolerance test based on feedback from makes. Please check fit with this part and adjust XY scale for desired fit before printing the whole part. Background I took the basic design from my M12x1.75mm shift knob and adapted…
Fully 3D printable lawn sprinkler that propels itself with water pressure and follows a path set by the garden hose. BOM: 3D Printed parts 1.5mm wire or paper clip ¾" BSP Standard Garden Hose Adapter Print Instructions: PLA (suggest…
This model is inspired by this adapter: https://cults3d.com/en/3d-model/game/adaptador-secuencial-logitech-g29-g27-sequential-adapter-logitech-g29-g27. The model is good but I wanted it to be more tight fitting and to be able to use…
If you like my designs, why not come and say hi on Instagram or Twitter ! Overview: Mr Bean's Leyland Mini with all the parts needed to recreate the infamous armchair driving scenes. It can be printed without the armchair driving parts if…
Logitech Driving force H shifter Console to mount to Playseat Challenge. Ends up being a quite nice starting setup for a driving simulator rig. Use PETG with 35% Gyroid infill, and 2pcs M4x30 Screws with washers to mount. 2019.02.20: REV3…
I really liked Forker45's shift knob and the fact that H3wro's uses the original logitech shift knob cap, so I combined them together to make this! The picture of my print in black were H3wro's original model (I also uploaded his file)…
I broke the clamp 2 years ago and created quick replacement, that broke down last week so I finally made a proper one
Shift Knob Threaded Adapter for Logitech Shifters Ever wanted to put an actual shift knob on in place of the Logitech foe leather knob? Do it! Install ; Remove logitech foe leather shift ball by popping off center cap. Unscrew standard…
The original driving shaft broke in the middle of the screw part. I printed it in PETG according to the instructions, but apparently the walls are too thin. So, I created a remix, which has a reinforced screw and the "top" end of the…
This model is compatible with the lego system.
In addition to a sequential shifter, Logitech Driving Force GT steering wheel has little nubs behind the wheel for changing gears. Those are not very nice to use. This design is for an add-on shifting paddles that are attached around the…
This model is compatible with the lego system.
This model can be used as a spacer to increase tension in the spring holding the ball bearing thus improving the overall feel of the shifter. I created this as a replacement for the bolt mentioned by the gentleman in this YouTube video:…
A Sparco driving force shift knob. Just use the original screw, no need for adaptors or mods. Support is not required but it may be helpful to add manual support right at the bottom. Just place the S Logo on top, Youi can glue if you like…
Remixed Elod_HU's model as the original was placed too far back. The remix is 100mm further up.
I grabbed Esteban16899's paddles because I think the larger paddles look and feel better on Mape's awesome Paddle shifter mod for the Logitech Driveing Force GT steering wheel. But I didn't like the cut outs so all I did was make them…
Lego Technic Driving Ring Connector
This model is compatible with the lego system.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
I really like to smoke cigarettes when I'm driving long trips (Smoking kills). So I made this design to hold my cigarette pack and my lighter. It's made for classic 20 cigs pack and big BIC lighter Very effective, it's attaching on most…
Caution: For this model, you need five colors. Or print the hat and glasses in different colors. Print Settings: Layer Height: 0.16mm (Or lower) Infill: 10% Infill Type: Grid - Gyroid Filament: PLA Supports: No Brim: No
A simple Tee to use on the Driving Range. Height 50mm / 70mm Material TPU (95A) Printing Time ca. 1 hour Wall loops 3 I have provided .stl files for 50mm and 70mm. I also provided the .f3d files. Strongly inspired by:…
3003 Fantasy Bits Mega STL Collection on Kickstarter Here’s the updated version with the correct Patreon link: 🔥 Want to stand out in the 3D printing market and attract more customers? 🔥 Now’s your chance to sell unique, stylish, and…
This entirely replaces the stock spring in the Logitech driving force shifter (G27, G29, & G923 shifters). The print settings are very important as the wrong settings can make it too soft, or too stiff causing the steel ball to pop out of…
This model is compatible with the lego system.
Instax Wide Main Driving Gear should fix 100, 200, 210, 300
HackerBox #0089 came with a fun Wardriving project built on a main circuit board with external antennas and a microscopic display board. Here's the product page Here's the build instructions This should print nicely in whatever PLA you…
This fastening knob is made for the Logitech Shifter for the G920 wheel and various others. I designed it because I often move the setup between tables and getting a good tight grip on the table was always harder with the shifter compared…
This a tool that can be attached to a standard drill or screwdriver bit to help drive hooks. It's large enough to also work by hand - without being used as a drill attachment. Includes .stl file, and fusion 360 .f3d file. Print Settings…
the MMU had standard PLA settings. Version2 has got three benchies and colored window sills sliced in PETG. Colours are: 1 is gold, 2 is green, 4 is white and 5 is red. The waste tower is the same size if you produce one or three and time…
Description This model is free and took a lot of work to create. If you appreciate this model, please leave a download and a like! If you print this model, please post a make. About this model SpongeBob driving a boulder! Inspired by the…
Toad driving a car? What in the?
Remix of the original, just added 0.15mm of tolerance around the hole.
This is an additional drive bit storage rack for the case that comes with Ryobi driving bit sets. The case is modular and some sets can fit more bits than they come with if you print another of these and shuffle the existing ones around.…
I printed this tool with 50% fill and it worked great.
DIY 3D-Druck Bauprojekt eines motorisierten, selbst fahrenden Kamera Dolly. Mit verschiedenen Fahrmodi, die durch einen Arduino Nano gesteuert werden. Der Stromversorgung erfolgt durch einen eingebauten, aufladbaren Li ion Akku. Das…
This clip was designed by the Driving Simulation Laboratory at the Faculty of Computer Science of Schmalkalden University of Applied Sciences for integrating an original Logitech G Driving Force Shifter into a real Opel Corsa B . It is…
Bring the beloved underwater world to your desktop with this incredible SpongeBob 3D printable STL model that captures pure childhood joy! This detailed figurine showcases SpongeBob SquarePants behind the wheel of his trusty boat-mobile,…
Small and easy print. Designed using Fusion360.
Although slicers don't recommend supports, I say it is needed. =D For better results, needs a M4 headless fastener layer height, 0.2mm wall count, 3 top/bottom layers, 6 pattern, gyroid infill, 10% print speed, 70mm/s normal support,…
NEW VERSION V2 : with slopes making the cards sliding in more easily I really like to manipulate cards when I'm driving long trips (100% safe of course). So I made this design to hold my deck of cards (with or without the pack). Very…
GT GranTurismo - Driving Simulator Videogame - Key chain - Portachiavi - Porte Clès - 钥匙链 - Schlüsselanhänger Resize to adjust dimension If you download/enjoyed this file, please leave a like - Thks Category: Video Games All trademarks,…
The driving wheels of McCulloch lawn mowers wear down. Rather than buying new wheels, I tried printing a new shell to put on top of the worn down driving wheel. There are 3 different sizes, pick the one according to how worn down your…
It consists of two parts. It's best to glue them together with superglue. The bottom might not fit perfectly. I heat it up a bit and slide it in to even it out. If it doesn't fit, I add a little more glue while it's still hot :) I printed…
I made this sign for the release party of KEEP DRIVING by Y/CJ/Y games. Check it out on STEAM: https://store.steampowered.com/app/2756920/Keep_Driving/ The pictured print was printed on a MK4S with the HF0.4 nozzle. PLA 0.2mm Infill 15%…
Summary This extended attachment for the thread of the Logitech Driving Force Shifter allows an installation on thin tabletops / desks and enhances the stability. Advantages Allows for mounting on thin tabletops Increases the stability of…
My desk has a chamfered edge so the clamps on my Logitech G Driving Force shifter didn't quite fit. These extensions are designed to loosely fit on and extend the clamps out and allow the shifter to be securely mounted to the desk without…
I designed a taller and wider front wheel, along with a taller rear wheel with more teeth, for the self-driving sprinkler tractor. These changes were made for two main reasons. First, the original design could sometimes get stuck in the…
Whenever my father had a co-driver in the last 30 years, who always knew everything better, he simply pointed at this sign. Most people in Germany can not speak or understand dutch. Now it was up to him to blow the story up and slowly…
HackerBox #0089 came with a fun Wardriving project built on a main circuit board with external antennas and a display board. As part of the project, they provided a 2.4 GHz PCB Yagi antenna, as a bare circuit board. While we can…
I bought a second hand GT driving force racing wheel second hand and it was missing the original tool for tightening the clamps. i designed this print to enable me to secure the wheel. Prints without supports
I found the original model after wanting to mount my own bit set. The original was great but made for the ryobi wall system. I only needed one slot and use the multiboard system, so I modified it to make it compatible. The front wall was…
A reproduction of a cam stack driving gear, made for a Singer 760 that needed a replacement of the original one which was cracked. This model has two notches to fit into the bottom of the plastic cam stack as shown in the pictures. I…
Piggy bank with comic car symbol. Perfect for birthday partys to gain money for your driving licence :-) You can of course add any kind of text via your slicer as I did for our son who make his driving licence for European class B and BE.…
The V2 container features several improvements over V1, including a new smaller 6-node variant, ventilation for improved cooling, smaller size, and support for dedicated battery controllers. These containers hold 6 or 12 Seeed Studio XIAO…
This is an all rounder keychain for any car.
This is Kyoto Driving Park - Yamagiwa from the Gran Turismo series (Specifically GT Sport) I have included the track, a display block, and a terrible logo. More original GT tracks to come! Requests will be considered, however as a novice…
Front bumper vertical daytime running/driving/fog lights for Scion xB 2008-2010. Photos to be added soon! Updated 6-MAY-2022: Bezel part now extends further down the side of the body for a better match to vehicle body, as well as includes…
Improved V2 with 6-node and 12-node versions available now. This is a container which holds twelve Seeed Studio XIAO microcontrollers, each with its own external antenna, as well as a battery. I use it with XIAO ESP32-C5s for dual-band…
Replacement support for a Cibié Iode 40 driving light, probably fits other Cibié models and Similar lights, but i haven't tested. The model was copied from a original one that came in the pair of lights i used on my car. The print on the…
Re creation (not remix) of https://www.printables.com/model/216076-tightening-key-for-the-logitech-driving-force-gt-w Made for easier printing and added comfort Printed at 0.2mm layer height with 30% zigzag infill Also added .ipj file for…
Pulley, which can be installed to help keeping the filament untangled
This model is compatible with the lego system.
Designed for a 1.5" T-Slot profile. Required hardware: 4x M8 14mm hex socket head screws (16mm works too, in a pinch) 4x M8 T-nuts 2x M6 20mm screws Print in a stiff material (PLA should be fine) without supports of any kind. Remove the…
UPDATE: Please find the rest of the project files here: https://www.thingiverse.com/thing:5263556 This is a digital pedal that I designed to be used with MAME driving games through an arcade encoder board, but as it uses just a micro…
box for arduino with cnc shield v3 , connector for nunchuc , 3 connectors Dupont for stepper motors XYZ, voltage regulator for fan and leds
I printed this as the model sits with tree supports, but excluding support along the axles. The original car model can print on its side, but I've not tested it with this.
I remixed the original stl file in order to be usable for any sim wheel that uses the standard 70mm bolt pattern for mounting, hole diameters are 5mm but they might need to be drilled depending on printer settings (still have the original…
This ground anchor driving nut makes it easier to drive anchors into the ground for swingsets or trampolines. I was having difficulty installing ground anchors for my children's swingset. It was difficult to install by hand into the hard…
Cake topper that you can print for your friend's passing driving test celebration. Printed from PLA but I recomend PET (food safe) if you really plan to put this in a cake (i don't cause my Jennifer didn't pass again on 7th time, but…
We had a donkey with cart in our garden and there was no one to drive it. So I printed a gnome. I used PETG, 0.4 nozzle, lightning infill. I painted with acrylic paint. I screwed it to the seat with a 4x40mm screw. The model is just the…
No AMS needed. I have not used any support. Layer height: 0.2 mm Infill: 15%
This adapter allows mounting a Logitech G29 steering wheel onto a Logitech Driving Force wheel base. It is designed as a strong and straightforward mounting solution that ensures correct alignment and secure attachment between the wheel…
So you don't have to cut the original to make the hand break mod
Technic Driving Ring 2L 2473
Parts Required: *M5 40mm bolts x 6 *M5 lock nuts x 6 *Super Glue for paddle Inserts *Carbon Textured Build plate (to make paddles/parts look nice.) So after doing a bit of a search to find the right collection of parts which worked well…
Nunchuck Wii adapter for CNC motor driving housing In order to pilot the 2 stepper motors of my OPENSCAN scanner, i use a wii nunchuck connected to the CNC shield of the arduino remix of https://www.thingiverse.com/thing:951963
What is cooler than a 🍌 Banana driving a 🚙 car or in this case K.I.T.T from Knight Rider. Download Like Favorite and Boost drop a comment on how it turn out.
20 Xioa C5's, two 10mm push button switches, one 12mm pass through for USB power.
Driving dog for a metal lathe. After plans from Harald Hall .- See: https://www.homews.co.uk/page305.html You will have to cut the 2 M6 threads for 1 x M6x16mm 1 x M6x40 or 50mm
Pretty straight forward cap used to step on, push, or hammer a spike into the ground. This cap was designed to fit the HRD spikes used in his products. The project file is the best route since it has a modifier set up with a high infill…
DIY 3D-Druck Bauprojekt eines motorisierten, selbst fahrenden Kamera Dolly. Mit verschiedenen Fahrmodi, die durch einen Arduino Nano gesteuert werden. Der Stromversorgung erfolgt durch einen eingebauten, aufladbaren Li ion Akku. Das…
What is cooler than a 🍌 Banana driving a 🚙 car or in this case K.I.T.T from Knight Rider. Download Like Favorite and Boost drop a comment on how it turn out.
This model is compatible with the lego system.
I designed a taller and wider front wheel, along with a taller rear wheel with more teeth, for the self-driving sprinkler tractor. These changes were made for two main reasons. First, the original design could sometimes get stuck in the…
Shifter knob mod. Using original screw to mount the adapter, long shaft and locking to prevent breaking and over-tighten. Long version could be sensitive against breaking above the threadline. Short version in use since a few years. Screw…
GT GranTurismo - Driving Simulator Videogame - Key chain - Portachiavi - Porte Clès - 钥匙链 - Schlüsselanhänger Resize to adjust dimension If you download/enjoyed this file, please leave a like - Thks Category: Video Games All trademarks,…
Brides of Dracula - Peter Cushing "Driving the Stake" - Hammer Files - 1960 3D printable model.
Print it vertically for the best results, no supports are needed. Print it out of a strong plastic and lots of infill for best durability.
