Liczymy pasujące modele…
Made it for my YK4106 Pro/FMS FCX10/Absima Wolf and FlySky MG11 radios (FS-MG11-BS, FS-MG11-BT-BS). I can barely reach the steering wheel with my thumb so I made this little adapter. 29-03-2026 : added a thicker version for a easier reach…
THIS MODEL HAS TO BE MIRRORED TO GET THE SECOND PART OF THE MOUNT WORKS WITH FMS 1/24 CRAWLERS, WILL PROBABLY WORK ON STUFF LIKE SCX24 AND 30
FMS FCX18 Toyota Land Cruiser 80 Inner fenders with side steps + display stand This model is designed for the FMS FCX18 Toyota Land Cruiser 80 version with removable fenders . The set includes: Inner fenders with integrated side steps /…
FMS Ranger RC plane Insta GO 3s mount for if you wanna film a POV from your RC plane
FMS FCX18 Toyota Land Cruiser 80 inner fenders with side steps. Print with tree supports due to the side step/rock slide part of the inner fender. Two screws are already present on the chassis to mount the inner fenders. The inner fenders…
FMS FCX10 front bumper with an integrated mount. It features a winch plate mount, license plate mount, and towing shackle mount. Several variants are available: I suggest printing with supports to strengthen the chassis mount part (to…
This is v1 and it is still in work. Frame can be printed with little supports needed. Transmission mount can be printed without supports.
Made it for my YK4106 Pro/FMS FCX10/Absima Wolf and FlySky MG11 radios (FS-MG11-BS, FS-MG11-BT-BS). I can barely reach the steering wheel with my thumb so I made this little adapter. 29-03-2026 : added a thicker version for a easier reach…
Basic inner fenders ... nothing fancy, Q&D, just to close the void. To be glued to the body. Engage back first. Might require to fiddle a bit around the leds. Might redo them better in an undefined, but not close, future ... Category: R/C…
A bumper extension to move it forward and provide more space for a winch, but also to look a bit more scale once you move the front axle forward a bit. Uses the same screw sizes as original ... so need 3 more. It's a tight fit ... and…
Simple stands for FMS 1:6 and 1:10 platform (not yet tested on Willys). Requires 2 sides, one low-beam and a pair of leaf-spring or links upper-beams according to your truck. 21-09 : updated the beams for links with better clearance and…
Needed something to install my PNJ gimball cam in the FJ40 that can stay even if I'm not using it. Fits tight so no glue really required. Just disconnect the lower seats from their feet, install the crate, then reconnect the seats.…
Some exhaust parts for "1:10" FMS FJ40. Designed for 6mm aluminum tubing. Requires longer screw for skid plate hangers and glue for the mufflers' halves. Category: R/C Vehicles
Rear mud flaps for FMS FJ40, their latest big-scale (more 1/7th than the advertised 1/10th) ... TPU of course. Sildes onto the rear body rod. 23-09 : added new mudflaps, 2 short, 2 long, each either plain or with "Land Cruiser" text. All…
Longer shackles for FMS Mashigan with leaf-springs kit. The way the leaf-springs are designed, you either end-up with a lowering kit if you go axle above or a high-heels kit with axle under ... Easiest way to correct the lowering kit is…
this is a part made for the FMS FCX24 because this part comes from China and takes forever to get here so I made one that will print and work for the FCX24. I now will be using Onshape for my designing because the slicer software likes it…
Need 6mm OD aluminum tubing. Cut to taste and glue (cyano should do the trick). Should also work with the FCX10 K5 provided you print a mirrored one for the driver-side.
The stepfile is only the left side. Just mirror the side for the other. printed without support.
A remix of two models which combine into a simple way to attach your camera to your RC FMS 1220mm Ranger V1 or V2. The first model is the insta360 Go2 camera mount found on Thingiverse: https://www.thingiverse.com/thing:5346685 The second…
The FMS fox 2300mm tends to lose the cap of its spinner. Despair no longer. This one is an easy replacement. Fits the original and clicks on when some pressure is applied. Glue if you like, but it should not be necessary.
Replacement wing strut for the FMS Ranger 1220mm. This is nearly the same as the OEM strut save for a small flat spot that should be oriented down towards the bed. Supports are necessary for the two small protrusions that connect to the…
Simple trailer hitch that fits the standard rear bar on the FMS fcx18 Lc80. A 5mm ball joint fits snug over the ball.
Drew these up myself for ease of printing. STL is left and right. Same file is compatible with front and back. May require 180degree rotation in slicer to make it easier to print. Enjoy.
a holder to mount to the underside of a shelf to hold your fms pa-18 500mm bush plane. I used sticky 3m stuff to hold them on
A FMS 500mm PA-18 Super Cub holder print as shown in picture
3D Printed Replacement Nose Gear for FMS Ranger 1800mm This is a 3D printed replacement part for the nose gear of the FMS Ranger 1800mm. The original aluminum gear can easily break during rough landings, so this part provides a more…
This printed part helps you landing with FMS Futura 64mm edf. Front landing gear stay straight also in hard landings. Looks nice:-) Use rubber liquid glue to attach, its great! Shoegoo, Bison or similar Good material: ABS or Petg, Tpu and…
A Bomb release mechanism that allows to drop ornaments for the FMS PA18A using the original screws. Besides the PLA parts, is needed to add a steel rod to attach the ornaments. You can also skip that, using a longer servo arm, but is not…
This is a tow release for the FMS Fox 2300mm V2 glider. It is shaped to fit into front cooling vent, and includes a channel to allow air to continue to flow through the vent. To complete the tow release you will need: 9g Servo - such as…
This is the Propeller Mount and Cover which I designed in TinkerCAD for my FMS ASK 23 R/C Glider, based on the original one I bought before. This can also be used on FOX and ASW 28 Glider from FMS. Printed the Cover with Layer Height 0.3…
FMS FCX18/FCX24 Wall Mount – Because Your Floor Isn’t a Garage Sick of tripping over your crawler and transmitter? Hang that beast on the wall like the trophy it is. This simple 3D print keeps your RC life tidy and your significant other…
Created a new transmitter wheel for the FCX18 LC80 since it didn't have a foam ring. This is a 2 part model, glue the hub to the wheel to give it some dimension. I also included a flat version without the hub.
Created a new transmitter wheel for the FCX18 LC80 since it didn't have a foam ring. This is a 2 part model, glue the hub to the wheel to give it some dimension. I also included a flat version without the hub.
This is a swing away tire carrier for the 1/10 FMS FJ40 Rock Crawler. Requires some extra parts. I used the RC tire carrier from amazon like this one -> https://www.amazon.com/dp/B0BTCZ8T3K?ref=ppx_yo2ov_dt_b_fed_asin_title For the hinges…
Print in TPU or PETG for the mid part that is in contact with the hot Vista unit. Print the mid section upside down with the curved surface facing up. Support is required, but that is easily broken off. Print with 0.1mm layer height, for…
THIS MODEL HAS TO BE MIRRORED TO GET THE SECOND PART OF THE MOUNT WORKS WITH FMS 1/24 CRAWLERS, WILL PROBABLY WORK ON STUFF LIKE SCX24 AND 30
FMS FCX18 Toyota Land Cruiser 80 Inner fenders with side steps + display stand This model is designed for the FMS FCX18 Toyota Land Cruiser 80 version with removable fenders . The set includes: Inner fenders with integrated side steps /…
This part fits the underside of the wing on the FMS Futura 64 EDF and covers the exposed aileron and flap servo horns when the landing gear is removed for belly landing configuration. I've also added a matching front skid for those who…
FMS Ranger RC plane Insta GO 3s mount for if you wanna film a POV from your RC plane
I love my FMS FCX24 for it's scale look and climbing abilities. The original bumper limited the approach angle and hooked twigs occasionally. That's why I created my own version. You need to cut the front fender slightly, to get a snug,…
This is a light weight exhaust nozzle modification for the FMS Futura 64 mm EDF jet intended as a speed optimisation, not a thrust modification. The stock outlet on the Futura is approximately 58 mm. These designs reduce the exit diameter…
A small spacer to mount a Hobbywing quickrun mini24 (or other motors with a larger diameter than 16mm and longer pinion shaft.)
Rear LED light for 1400mm FMS Cessna 182 RC aircraft model I used 4,8mm WS281 LEDs and my Vacuum forming table for glass cap.
3D-printed replacement part for Whirlpool air conditioner AP12DR2SFMS.FJ-01, diameter 150 mm. Designed as a repair part for a damaged or missing original coupler, restoring function without replacing the whole assembly. This model is…
The FMS 800mm Beaver wing is secured by a plastic quick-release wing key located at the rear of the wing. Since this small part can be easily misplaced during transport or field assembly, I designed a replacement that can be printed at…
A cover for the buttons on the FMS FCX18 remote. You will need to heat up the cover slightly to have it contour with the top of the remote. Use 1.75mm filament for the hinge. A 1.8mm drill bit may help if you can't push the filament…
A cover for the buttons on the FMS FCX24 remote. Use 1.75mm filament for the hinge. A 1.8mm drill bit may help if you can't push the filament through the hole. It also includes a hole for a 3x6mm magnet.
FMS 800mm Beaver Wing Strut Replacement I managed to break one of the wing struts on my FMS 800mm Beaver and decided to model a replacement instead of ordering new parts. This is a complete one-piece replacement strut that fits either the…
This is a replacement gear for the center rollers on a HoMedics foot massager, model FMS-150H. It includes the main gear and the smaller gear that meshes with it. You'll need to print two of the smaller gear. Print instructions Print at…
You can use that template to cut sandpaper required by the Metabo FMS 200 Intec delta-shaped sander . Holes in a paper sheet are 8 mm in diameter, holes in the template have diameter slightly bigger to use a punch cutter freely.
Mini FMS Huddison Discord Server (for more information and config files) https://discord.gg/xDKwFYDsZk Mini Autopilot in this video is also available to make. Software used - Mobiflight - https://www.mobiflight.com/ Parts list Pro Micro…
easy to print. no support needed. I printed with PLA it fits perfect for the FMS sender. perfect for onehand driving.
The FMS 1700mm Piper PA-18 Super Cub wing-mount posts are prone to breakage - well at least my dad's broke. Unfortunately, the mounts are glued to the foam fuselage and a new fuselage costs $70USD+shipping. Here is a replacement part for…
Clamping jaws for the Proxxon FMS75 precision mechanics vice for clamping round material. There are jaws for round material with a diameter from 4 mm to 12 mm in 0.5 mm steps. Other diameters between 4 and 12 mm can be created with…
These are designs to replace the bumper construction or part of it. If you want another bumper design drop me a message. The best design is the single piece bumper, good clearance and strong.
Bisley hanging file cabinet bracket for 5x Stanley FatMax FMST1-75779 Shallow Organizer I removed the metal hanging file brackets from the drawer. I printed this model 4 times, per drawer, in ABS and mounted using double sided tape…
Stanley FatMax FMST1-75779 Shallow Organizer Dividers for the large and small bins I used a 0.2mm layer height with a 0.4mm nozzle and printed in PLA Included is the f3d file A lid exists, to prevent small washers to move to another bin.…
Stanley FatMax FMST1-75779 Shallow Organizer Lid for the small bins This lid exists, to prevent small washers to move to another bin. I used a 0.2mm layer height with a 0.4mm nozzle and printed in PLA Print with the top of the lid on the…
FMS FCX24 Chevrolet K5 Blazer FPV camera mount for Diatone SNT Sniclo Race480 FPVBOX camera. Snaps to FXC24 frame. Prints with supports upside-down. I used double-sided 3M tape to mount the camera. Version 1 - first version, camera can be…
Simple stands for FMS 1:6 and 1:10 platform (not yet tested on Willys). Requires 2 sides, one low-beam and a pair of leaf-spring or links upper-beams according to your truck. Only tested on FJ40 yet. Requires 6 M3x8/M3x10 screw for…
Rear mud flaps for FMS FJ40, their latest big-scale (more 1/7th than the advertised 1/10th) ... TPU of course. Sildes onto the rear body rod. 23-09 : added new mudflaps, 2 short, 2 long, each either plain or with "Land Cruiser" text. All…
Some exhaust parts for "1:10" FMS FJ40. Designed for 6mm aluminum tubing. Requires longer screw for skid plate hangers and glue for the mufflers' halves.
These pods are designed to fit the leading edge of the FMS Supper EZ trainer. They fit so well the alignment is easy. RaceStar A2212 1400Kv motors were used on 3s 2200mah. The flight characteristics are fantastic. Even flies inverted with…
Instead of buying the crappy rims that last only a few days of flying, try this ones. Glue them together. And you are up flying again in notime. Fits the OEM 5 inch bush tires
2023-11-15 These front inner fenders are designed for the FMS FJ40 Cruiser (1/10th scale). The left fenders encapsulate the servo for the steering wheel and have a slot for a battery strap. These parts were designed and fitted, I didn'…
This is FMS R3A Transmitter holder for IKEA Skadis pegboard. This transmitter (controller) comes with FMS FCX24 cars, I had it with Chevrolet K5. This item is inspired by IKEA SKADIS Collection by CSD Salzburg, it uses the same hook…
I needed an adapter to plug this sanding machine to my vaccum (35 mm). It was a little bit tricky to adjust it perfectly. It fit just a little tight to the machine so it won't move when we use it. It's not the best design i've ever made…
Warning - the mounting holes/webbing inside the cutout are not perfectly centered. The window cutout is fine, and this just means that the inside guide will only fit in one orientation. It's such a non-issue that it wasn't worth fixing…
The FMS FCX24 cassis has a two-speed transmission. The transmission rod leaves on one side of the transmission for the servo and on the other side to manually lock it to one gear permanently. The side to look it always works some sand…
The lift kit from the original file was a bit too much for me, I didn't like the look. Edited the file for less lift. I then wanted more flex on the rear axle and came up with the revolver type shackle. It gives alot more flex. You will…
Designed this around the QX-Motor 30mm EDF 7000KV For the FMS Alpha Free Flight Airplane https://www.horizonhobby.com/product/free-flight-alpha-red-kit-467mm/FMM073RED.html . Intake area is slightly more than EDF. Exhaust area is about…
Soportes de los misiles del Rafale de FMS. Tiene dos averturas para que se vean la luces. He intentado que valga para las dos alas. El original tiene la forma del ala.
FMS FCX18 Toyota Land Cruiser 80 inner fenders with side steps. Print with tree supports due to the side step/rock slide part of the inner fender. Two screws are already present on the chassis to mount the inner fenders. The inner fenders…
This is a longer version of the original FMS Pitts V2 140cm accu tray. It supports now 6S 5000mAh Lipo accu to get the correct COG without adding too much weight to the tail.
Use these prints to replace the weak struts on this model. Note: This design is not perfect, but it works. I did not realise that the front strut is swept forwards slightly, so there is a very small bend in the strut. This has not been a…
FMS FCX10 front bumper with an integrated mount. It features a winch plate mount, license plate mount, and towing shackle mount. Several variants are available: I suggest printing with supports to strengthen the chassis mount part (to…
Llavero de la liga de freestyle rap Freestyle máster series (FMS)
A small box for the cheap Sinilink XY-WFMS module. It is with a snapfit so no extra screws are required.
FMS FCX24 Chevrolet K5 Blazer hitch to connect Lego Duplo trailers and carts. Base is mounted to stock rear bumper mount with stock screws. The hitch part is detachable, just press on the sides to mount or remove it. It moves up and down…
FMS FCX24 Chevrolet K5 Blazer bottom protector. Works with my FPV camera mount . Needs 8 small screws to mount (make sure they don't stick from other side because they can scratch steering servo). You need to print: 1 Left protector 1…
I was using a 50mm FMS EDF in the Skyray model published by PTIKyle. The FMS EDF has a narrower bell and a narrower body than the XFly units, resulting it in falling into the duct and not being sealed. This is a quick shim set to make the…
