46 modeli
Get fan and heatsync combo at: https://www.amazon.com/gp/product/B07PCMTZHF/ref=ppx_yo_dt_b_asin_titl
Wydruk około 1,23 €–1,50 € nettoWstępna wycena jednego wariantu
This is an modification of the original RPi4 UPS case by Jason with changes and upgrades for the newer revision of the GeeekPi RPi UPS hat (aka EP-0136) for Raspberry Pi 4 . UPS Link: https://wiki.52pi.com/index.php?title=EP-0136…
Wydruk około 0,06 €–0,07 € nettoWstępna wycena jednego wariantu
Uses 2 M3x8mm screws to mount to the frame. Print instructions: -Brim recommended -No supports -0.2mm layer height You can buy the case here: Case + Power supply: https://amzn.to/4f2fVIn Case only: https://amzn.to/40lDUOb Have included a…
Wydruk około 0,88 €–1,08 € nettoWstępna wycena jednego wariantu
Has been tested on 2 different screens to confirm tolerances. Tested Print settings- 0.2 Layer Height, 30% infill, printed back to face of build plate. To confirm the exact GeekPi 7 model I used here→ https://a.co/d/cPXtGqt I used 4 -…
Case für raspberry Pi
Pimped my Raspi with a 1TB NVMe Disk and a strong cooler. As I couldn't find a suitable case I made one - after some iterations it's good enough for my purposes, maybe also for someone else. I also attached the Freecad File.
Reference of current GeeekPi heatsink/cooler Links for the CAD projects I use to make the change: Top case (no STEP): https://www.tinkercad.com/things/36RtgzKxmBp-rpi-4-case-top-for-geekpi-fan Bottom case (STEP):…
Shelf v1 is 4mm thick, which may have been too thick. Shelf v2 is 2mm thick, and made the mounting holes slightly smaller to allow more material for structural integrity Both are pictured in the rack. I included the F3D files if you want…
I printed mine on its side, but do what you think is best for your setup. there are also mounting holes for a raspberry pi, but would need some offsets of some kind.
Raspberry Pi 5 Case for GeeekPi N04 M.2 M-Key NVMe SSD Shield you need 4x M2.5 x 12 to fasten the Pi into the case the holes must be drilled out afterwards, because of the additional bridging layer just follow this guide to print the…
Fixed version of the Raspberry Pi 4 B top case with the GeeekPi Heatsink / fan , requires the base top of the original case model . Fits the GeeekPi Heatsink / fan combi .
I have two pi 5's on my pi server rack and both of them have the poe+ and nvme hat. This hat adds a challenge that it is just as long as the pi PCB itself and sits very high which required heavy remixing. I recommend longer screws to be…
There hasn't been much of anything available for these due to the chip shortage for the last year or so, but now that CM4s are trickling out into the wild I thought I'd pick one up and finally finish my router board build. No supports,…
This is a case and stand for the geeekpi 7in HDMI display. It sits at a 45 degree angle. Two model available, one that uses a 2mm heat set insert, the other for 2.5mm self tapping, to mount a pi to the back off the display. Feet Screws-…
Model for Rasberry Pi 5 with GeeekPi N04 M.2 M-Key NVMe SSD Shield
As the GeeekPi Raspberry Pi 4 Ultra Thin ICE Tower mounts from the underside of the Pi with either bolts or standoffs I had to modify the LDO recommend mount. I used the 4 x M2.5 standoffs that came with the ICE Tower to mount the ICE…
I've made this model because I was unable to find a case that was exactly made for this addon. I also made it able to fit an SD card if its necessary. The middle part is sandwiched between the Pi and the NVME bottom. The example in the…
# Printinfos * Printprofile: MK4 IS 0.20mm Speed (mit MMU3) * Nozzle: 0.4mm (Olson Ruby) * Material: Prusament PETG * Supports: none
The original design was great but I needed to include the NVME hat that I had. It should have probably gotten some additional support because the back sags a little. Ill end up having to prop it up somehow.
Eine einfache Halterung für einen Raspberry Pi 4B im GeeekPi-Gehäuse am MK3S+. Die Halterung wird mit zwei Schrauben an den vorhandenen Löchern am Rahmen des Prusa befestigt. Es braucht nicht gebohrt werden. Der Raspberry im…
This is a GeeekPi GPIO Screw Terminal Hat Mount for my DIN Rail Bracket. You can find the bracket here ! For the DIN Rail Bracket Mount you need M3 x 4mm or 6mm countersunk screws. For the GeeekPi GPIO Screw Terminal Hat I used M3 x 6mm…
Vent holes align with the bigger fan on the GeekPi heatsink
I wanted to add more protection for the bottom of the rack and the rack only comes with a pair of the horizontal frames which I used for the top. I have a version with no tab that works as just a horizontal frame, and another with a tab…
3u rack mount, universal to the left and or right hand side of the rack, holding a 7'' geeekpi display, with a screw mounting to hold the display in place if desired and back vent cooling. V2 will have additional supports to join 2 of…
A case for the GeeekPi P33 M.2 NVME M-Key PoE+ Hat on a Raspberry Pi 5 off the side of a rack. Picture is of previous version. I have improved structure. Will add additional picture when new one is printed.
Needed a riser for the GeeekPi Raspberry Pi 4 case to accommodate a Loverpi isolated PoE hat and would allow the 40mm x 10mm case fan to clear. I added some vents on the side to accommodate the case being on a flat surface with little air…
Raspberry pi 4 geeek case mount for prusa frame
PSU Mounting part of GEEEK A50 ITX case.
When I was searching for a case for the Raspberry Pi 5 I wanted to have one which maximizes passive cooling but also has “large” fan for when passive cooling is not enough. In the end I went for the GeeekPi passive heatsink and designed…
My Geeekpi display case requires at least a desktop stand, since the feet supplied with the display do not fit once the case is installed. I happen to have a section of Honeycomb Storage Wall (HSW) installed along the front of my printer…
Replacement handle for the GeeekPi DeskPi RackMate T1. Slightly shorter than stock, for additional clearance. Print your own to customize color or material. PLA is more than sufficient structurally. Printed on side, with no supports.…
I needed a box for my smarthome system Homeassistant with ESPHome. A GeekPi breadboard 1/2 fits perfectly into the box, for which I have integrated spacers. An ESP8266 with a Pyrexx PX-AR smoke alarm relay was then placed on the…
This is a remixed mod to an existing bracket that mounts a Pi4 on the Prusa MK4 with the GeeekPi case. I had to modify the original bracket because I installed a dual light bar kit from VoxelPLA and the original bracket caused the Pi to…
I was inspired by the flush mount The Stock Pot made for the Raspberry Pi Touch Display 2. But I enjoy playing with odd aspect ratios and I found this GeeekPi 11.26 ultrawide display and decided that was going to be my wall display for…
About I have a hard time swallowing the price of a name-brand Pi and started with an Orange Pi 3LTS. Took a bit more work to find some things, but it does its job faithfully in the house. I scored a deal on an Orange Pi 3B which has some…
10inch GeeekPi 12 Port Patch Panel cover that allows cable passthrough
I'm ocd, wanted this cable to lay neatly without crimping it and possibly damaging it. The geeekpi & geekworm fin dimensions differ. I found the fin distances to be pretty inconsistent, even on the same case, so.. I included both versions…
Connect the two parts with m3 nuts and bolts.
This shelf can be mounted to a wall with countersunk screws and can hold a Geeekpi Mini Tower
I noticed that there weren't any 52Pi/Geeekpi N16 board cases, so I took it upon myself to modify @ Quentin23Soleil 's Geekworm X1011 case to accommodate a 52Pi/Geeekpi N16 board. Might add a power button cutout if there's any interest in…
The venerable Netgear R7000 “Nighthawk” prosumer routers are a versatile piece of network gear, especially outfitted with DD-WRT, which is quite stable on that platform. My R7000 is no longer capable of doing what I need in wireless…
It suitable for Raspberry Pi 5 which are mounted inside this case by GeeekPi. https://www.amazon.com/dp/B0DFLVP88L The vents were kept open in order to prevent overheating. The USB-C power cable is supported so that it stays in place and…
Hi everyone! Here is my custom enclosure for the Raspberry Pi Zero combined with the GeeekPi USB Dongle . Enjoy and happy printing! If you like this model, please leave a like and a comment with your makes. Key Features & Design Choices:…
Model for Rasberry Pi 5 with GeeekPi N04 M.2 M-Key NVMe SSD Shield
I needed a box for my smarthome system Homeassistant with ESPHome. A GeekPi breadboard 1/2 fits perfectly into the box, for which I have integrated spacers. An ESP8266 with a Pyrexx PX-AR smoke alarm relay was then placed on the…
A case for the GeeekPi P33 M.2 NVME M-Key PoE+ Hat on a Raspberry Pi 5 off the side of a rack. Picture is of previous version. I have improved structure. Will add additional picture when new one is printed.
