Liczymy pasujące modele…
Simple LED diffuser for GU10 LED lights . I have these in my kitchen and although I love the LED lights, they are not diffuse enough. IMPORTANT: Print only 2 bottom layers and 1 top layer, or it will be too thick and light will not pass…
Wydruk około 0,25 €–0,31 € nettoWstępna wycena jednego wariantu
Fits on GU10 LED spots. Insert stuff like photo diffuser paper in the three slots an clip it on the light bulb. Fits on IKEA, Philips, innr and other bulbs. ONLY FOR LED SPOTS! Diameter: 55,4 mm, 51 mm Height: 7 mm Category: Household
I tried printing it in: PLA PETG Both worked with my 3W Bulb. Choose accordingly to the heat development of your bulb. Make sure your lamp doesn't get too hot!!!
GU10 spot, with cap, connectors and clamp clamp_counter: print on its side, with supports both connector bases: print vertically with screw on print plate. With tree support. For extra satisfaction: aim to get it off the build plate in…
ENGLISH: Finding GU10 LED lamps that also have a narrow focus for accent lighting with good colour temperature and colour fidelity and good dimmability is very difficult. I gave up at some point and designed these focus rings for myself,…
GU10 spot, with cap, connectors and clamp clamp_counter: print on its side, with supports both connector bases: print vertically with screw on print plate. With tree support. For extra satisfaction: aim to get it off the build plate in…
ENGLISH: Finding GU10 LED lamps that also have a narrow focus for accent lighting with good colour temperature and colour fidelity and good dimmability is very difficult. I gave up at some point and designed these focus rings for myself,…
Podstavec skála pro lampu planet velikosti 20cm se závitem a pro žárovky s paticí GU10
A clean, minimalist lighting solution designed for rental apartments and easy swaps. This is a non-destructive system that fits standard 50mm bulb holders (standard for E27 pendant cords and fixtures found in EU). How it works The Clamp…
Filament: - JAYO - white - PLA+ Objektgröße: ca. 10 L:B:H in cm Drucker: Prusa MK3S Düse: 0,4 Schichthöhe: 0,2 Infill: 100% Stützen: keine (evtl. die ersten 20 - 40 Schichten) Druckzeit: ca. 11 Stunden Die Mars-Deckenlape, sollte mit dem…
Filament: - JAYO - white - PLA+ Objektgröße: ca. 10 L:B:H in cm Drucker: Prusa MK3S Düse: 0,4 Schichthöhe: 0,2 Infill: 100% Stützen: keine (evtl. die ersten 20 - 40 Schichten) Druckzeit: ca. 11 Stunden Die Mars-Deckenlape, sollte mit dem…
print in vasemode/spiral outer wall and 0 bottom/top layers. I used brim for bigger buildplate contact area. Can't quarantee compatability with every GU10 lamp but give it a try! :) Added pics of my lamp so if yours is similar it propably…
Frühere Halogen- und Glühwendel-Strahler gaben nicht nur Licht nach unten (Downwash), sondern hatten auch etwas Streulicht, was besonders Milchglas-Lampenschirme lebendig aussehen ließ. Die Umrüstung auf LEDs hat mir bei der gezeigten…
An easy adapter for mic stands to mount most GU10 LED bulbs. I used a Shure mic clip. Additional hardware required: 1x GU10 base 2x M3 16mm bolts & nuts
1/4 scale replica of the ubiquitous PAR64 theatre lighting fixture. I've included cans for both a short and long version to suit your taste. For best results on the long can, line the inside surface of the tube with some aluminium foil.…
This design is from a request on my GU10 Parcan model ( https://www.thingiverse.com/thing:2431893 ). The only part that needs supports is the base. Additional parts required: 1x GU10 bulb holder 2x 15mm M3 nuts and bolts (for securing…
I designed these gu10 spotlights to mount some extra spotlights to the existing single point of wiring. The spots mount to the ceiling using 2 screws and have a number of holes to both have wiring enter from the ceiling and/or to adjecent…
IKEA Tradfri GU10 bulbs have a rounded bottom. This ring supports them in the EvoFire frame. There are two models. I've printed these in ASA to give improved temperature resistance. they are probably fine in PETG depending how hot the…
I remixed the lamp head for strength and a snug fit. I remixed the backpack to allow for a rocker switch. All parts are oriented correctly and the correct size, but the Dummy 13 parts must be printed at 250%. You will need supports for…
The stand for lithophane planets with support for GU10 socket. The GU10 socket should fit right in thanks to GU10 mount without any screws. There is enough space inside for terminal block as well.
this is a remix of the Dummy 13 GU10 lamp head. I made some simple vents in the top en bottom of the head
This is a spotlight for a GU10 bulb, which is mounted outside the thread. It is easy to print and looks clean. Dimensions: 75x75mm. 4 screws (4mm), a GU10 bulb socket are needed for assembly. SIZE: Box: 75x75mm Plate: 75x75mm Gypsum…
This is a lamp shade for a Philips Hue GU10 Bulb. The bulb fits firmly in the shade and gives off a great light. I designed this in fusion 360. I have a lot of Philips Hue lights in my place and needed some projection lighting, so I made…
Mold Preparation & Assembly Instructions Mold Preparation Coat every part of the mold with a concrete mold release agent (e.g., Vaseline) to ensure easy demolding. Assembling the Mold Frame The Mold Parts 1-4 are secured to the Mold Part…
https://www.ikea.com/us/en/p/nymane-work-lamp-w-charging-led-bulb-anthracite-20477751 I found one of these in “as-is” at my local IKEA thinking I'd be able to use a TRÅDFRI GU10 bulb, only to find an E17 once I got home. After doing some…
Did that for a lamp my brother bought for himself in Marrakesch - The lamp elektrics was done with sound cables and was really looking crazy life-threatening :O So i made this for him =) Happy printing!
Minimalist housing for GU10 Philips Hue bulbs. Snap-fit design, perfect for costom LED lighting setups.
SPOT reflector light art gallery theatre v.1 GU10
- Material recomendado: PLA blanco o PETG. - Resolución: 0.2 mm - Soportes: Solo para partes con salientes en los soportes internos. - Tiempo de impresión estimado: 6 a 8 horas en total (según velocidad y configuración).
I don't like the backside of the Hue Gu10 lamps, too much text and not the right color for me, so I made these caps
ich habe den druck von hier https://www.thingiverse.com/thing:1747650 sieht sehr gut aus
This is a ceiling light fitting for 3xGU10 bulbs bulb shader in FC file for individual custom switch box: h3xA_box_01_001.stl & h3xA_lid_01_001.stl are optional required fasteners: 7x M4x30 BHCS, 3x M3x40 FHCS, 6x M3 nut, 6x M3 washer…
Normally the spot light of the Phillips Hue Centura ceiling spot is too narrow in order to be used as a in-wall mounted stair light. This diffusor widens and softens the spot very strongly and hence makes it suitable for stairs. The…
Reduced the size of the original dome by seitse - so it can print on my Prusa Mini Original: https://www.thingiverse.com/thing:4142787 Print Settings Printer Brand: Prusa Printer: Prusa Mini Rafts: No Supports: No Resolution: 0.2 Infill:…
This fixture can be used to surface mount the LIFX GU10 Downlight or other low-wattage GU10 LED lights. It's designed to fit a standard American 4-inch circular electrical junction box. The base can accommodate a standard GU10 socket…
This tool is perfect for handling GU10 bulbs where your fingers can't go. The normal way of doing it is to use a suction cup tool - but it can be tricky to use - and some bulbs like Philips Hue GU10 are not suction cup compatible. The…
Description A sleek, adjustable spotlight you can 3D print yourself. Designed around standard GU10 bulbs, it’s affordable, easy to assemble, and stylish enough for any modern interior — perfect for accent lighting in living rooms or as a…
I made a spotlight cover that glows in the dark. As soon as you go to sleep or turn off the light, the PLA Glow in the dark starts to glow. It is not very usefull, but maybe fun for kids to fall asleep or just like me for in my office…
This adapter allows GU10 or GU5.3 (MR16) lamps to be used in AR111 / G53 fixtures . It’s a practical solution for situations where the fixture is fixed but the lamp type needs to change—for example when switching to LED. Compatible with…
Overview This is a variation of SpaceKaseJase's "Dummy 13 GU10 Lamp Remix" , designed to fit a different brand of GU10 socket. Required Parts Fasteners: (2) M3 x 12 screws GU10 Socket: Atron LA 99 (Available at Home Depot…
Printed with PETG and TPU Try out the printed parts if they fit together before mounting Mount the Bracket first put the Buffer Ring onto the bulb corpus put the Bulb with the Buffer into the Spot-Corpus (It should be flush) Make sure it…
Podstavec skála pro lampu planet velikosti 20cm se závitem a pro žárovky s paticí GU10
AURA design Leuchte schönes Design ist häufig mit hohen Kosten verbunden, besonders im Bereich der Beleuchtung. Dieses Projekt ist mein Ansatz, eine moderne, gut gestaltete Pendel-Leuchte zu entwerfen, bei der Form, Lichtqualität und…
About IKEA Tral has a mounting between the lamp and the GU10 ceramic socket, that uses two metric screws to keep it in place - the problem is that the mounting totally shattered around the screw heads and it just fell off. So I did a new…
I needed a simple box to store my GU10 for later so I made this and now you can have i too.
upravená základna a rozteč pro šroubky do objímky. Tisk Spectrum ASA 275. Na fotce zatím prototypy z PETG.
This is a lamp shade that clamps onto a GU10 bulb. It's in the style of barndoors like they are used for set-lighting in filmmaking or photography. I've printed this in PLA, no warping from the LEDs heat whatsoever. Consider using PETG…
Do NOT use this fixture with standard halogen GU10 lamps unless you are sure the filament you've selected can accommodate the extreme heat. This design is offered with NO warrant of safety or liability. If you choose to print/install this…
Drilled a hole in the ceiling to mount a GU10 recessed light only to figure out there is no power? Meet myself.... Facing the same issue? Print this cover plate that fits nicely in any GU10 mount to make it look less jank. Printed with…
Elevate your home lighting with this minimalist, designer-inspired ceiling spotlight . Specifically engineered for GU10 LED bulbs , this model balances professional aesthetics with safety-conscious engineering. Verified Thermal…
A clean, minimalist lighting solution designed for rental apartments and easy swaps. This is a non-destructive system that fits standard 50mm bulb holders (standard for E27 pendant cords and fixtures found in EU). How it works The Clamp…
Stores 15 E27 or GU10 lights. Print upside down to not have to worry about supports. Use no top/ bottom layers and hexagonal infill to get the look like in the picture. In my case I had full walls, but that just wastes a lot of filament,…
Hallo liebe Community Hier findet Ihr eine Variation von Aufbauspots / Aufbaustrahler für GU10 Fassungen und LED Leuchtmittel. Der Basis Sockel kann mit den Befestigungslöchern auf eine Standard Hohlwanddose oder Unterputzdose geschraubt…
Do not assemble this if you are not an electrician, it is potentially dangerous wall plug device. To minimise risk this project uses standard DIY plug and bulb mount with all necessary tests and temperature resistance. Use GU10 low power…
Es wird ein Gewindebohrer für M10 benötigt. A tap for M10 is required. Viel Spaß! Category: 3D Printing
Printable downlight fitting for a GU10 lamp. The springs holding it in place and the spring holding the lamp in the fitting needs to be taken from an old fitting. I used these to replace the fittings in the bathroom since these were…
Attention! The moon lamp has to be printed at 80%scale to fit this! I did that because it would not fit on my prusa Mini otherwise. Print it from the provided .3mf, I suggest. Use a standard GU10 Socket, solder the wires to a power cord…
I was replacing my old 12V halogen bulbs with 230V LED bulbs and I needed a custom mount for the new GU10 socket bulb with a 63mm ceiling hole in mind, so I created this fitting. CAUTION: Consult a certified electrician for any electrical…
Lampshade for GU10 lamps to reduce the beam angle, as a reading lamp.
Spotlight GU10 enclosure with interlocking bracket specifally designed for the Philips Donegal line, but might fit other brands Designed for when you want spotlights but do not have enough space between your ceiling and false ceiling.…
new diffusors for christmas https://www.printables.com/de/model/64058-spotlights-lampshade-v2-gu10-or-12-v-led-diffusor- You probably know all of these cheap lights that contain GU10 lamps. Most of these lights are kept very simple and…
Fits for IKEA, Philips, innr, Osram and other GU10 LED Spots. You can combine both bodys with both inserts. Height: Large Body 97 mm; Small Body 82 mm For LED Spots only! Category: Household
This accent light fixture is printed in two parts – a base and a top section. They do not require supports. This accent light fixture is designed specifically to fit a Phillips Hue GU10 LED Smart Bulb. It should also work with other (and…
den Sockel unbedingt mit support drucken, das Lampenglas transparent. Für die Lampenfassung einfach eine Gu10 Lampenfassung im Baumarkt kaufen. Das Zwischenteil was hier nicht zum download bereit steht habe ich auf einer anderen Webseite…
I wanted to make my kids night light smart, however, the original bulb holder was for e27 fitting and all the smart e27 bulbs I could find were too tall. The GU10 versions were much shorter, so I designed this part to take a standard GU10…
Lamp shade for gu10 light bulbs. The shade is printed in vase mode.
I have made a GU10 lampshade that can be attached to an LED spotlight. Lampshade printed in vase mode extrusion width 0.8mm (I have used a 0.4mm nozzle), no upper and lower layer, just a perimeter, layer height 0,18mm Update 18.03.2019…
lampshade for GU10 LED spotlights based on my first design https://www.thingiverse.com/thing:3498515 I have made a GU10 lampshade that can be attached to an LED spotlight. Lampshade printed in vase mode extrusion width 0.8mm (I have used…
Lampenschirm für GU10 und MR16 LED Leuchtmittel Einfache und praktische Lampenschirme für die meisten GU10 und MR16 LED Leuchtmittel. ____________ Lampshade for GU10 and MR16 LED bulbs Simple and practical lamp shades for most GU10 and…
in my cupboard above the sink, small halogen bulbs burned out I didn't want any more because they got terribly hot and didn't give much light at all so I decided to put gu10 bulbs in there but I wanted it to look nice too, and then i saw…
Motivation I need nightstand lamp to read bedtime stories to my son but the GU10 lamp is too bright and annoys him. Also it's a way to show off those vividly colored filaments. Printing There are overhangs, so supports are required. The…
simple box to hold a gu10 lamp. only 1 screw to hold it. simple print, no need for supports. 0.2 layer and fast print on prusa mini + caixa simples para acomodar uma lâmpada gu10. Apenas 1 parafuso para segurar. impressão simples, sem…
The base of the lamp features a GU10 socket where the bulb can be inserted. The base is designed to securely hold the lampshade and provide stability to the lamp. I printed it in vase mode with a 0.4mm nozzle and a width of 0.6mm Parts…
Eine Leuchte welche ich für unsere Küche entworfen habe. Gerade die Kombination von LED-Strip für indirekte Beleuchtung und GU10-Strahlern für eine gerichtete Wirkung war Ziel dieses Projekts. Um die Teile auf die Druckplatform zu…
I have a lot of Ultralux LLVP1242 downlights at home. Every month I have to replace at least one or two of them, and it's gotten quite expensive (at 12-15 euro each), so I decided to convert them to regular GU10 LED bulbs. This model…
We use a Franke FSMA 905 hood at home, and the lights that are delivered with the hood are a very sterile white color, with horrible color rendering. I use Home Assistant for my home automation, and all in-house lights have so-called…
this design is made to fit 2020 aluminum profile. you will need to add: Allen screws, NY lock nuts and t-slots lamp switch cable GU10_PAR16 socket all available on amazon I will update links in the future. Enjoy https://www.salvador-3d.com/
Stínidlo dá bodovému zdroji částečný charakter zdroje rozptýleného. Světlo je měkčí a vlastní dioda LED je z většiny úhlů skrytá přímému pohledu Čirý filament dodá efektnější vzhled, bílý měkčí charakter světla. Model je nutné vytisknout…
Redesigned the stand, and added a circular box to hold electric connections and GU10 light bulb fitting.
You probably know all of these cheap lights that contain GU10 lamps. Most of these lights are kept very simple and can easily be converted to economical LED light sources. Compared to halogen spotlights, LED lamps not only have the…
Updated printable downlight fitting for an LED GU10 lamp. The springs holding it in place and the spring holding the lamp in the fitting needs to be taken from an old fitting. I used these to replace the fittings in the bathroom since…
I use this very simple lamp base with Philips Hue GU10 bulbs. The shape of the GU10Cube allows it to be positioned in different ways, so the light beam can be aligned horizontally, vertically or at an angle of 15°. This makes it easy to…
A simple clip in place light restrictor that allows for the beam of an LED GU10 to be directed onto a peice of art or room feature. I made two designs, one provides a single directed beam, the other provides two directed beams. I used…
Ein simpler, einfacher und günstiger Weg deinem Zuhause (vllt.) das notwendige ETWAS an Licht / Atmosphäre zu verleihen. Dutzende Anbieter versprechen schönes Design → aber zu einen hohen Preis! Hier die Lösung: Druck dir deine eigene…
Very minimalistic GU10 lightbulb holder for storing lighbulbs.
Tool for GU10 Ceiling Lights Tool for removing GU10 size bulbs from ceiling mount light fittings. Locates on the three lugs on the retaining ring allowing it to be rotated until it comes free. Since the 'photo I cut a cone into the base…
editted version, Phillips Hue are slightly different in shape then normal GU10.
Moved into an apartment that had some GU10 downlight spots installed in the ceiling with the mounting plate missing - the bulbs were simply hanging through the spot. Instead of replacing the whole spots - I modeled a replacement that fits…
For led GU10 lamp, special to be installed in standard switch box
IKEA Tradfri GU10 Light Diffuser ⚠ Please note ⚠ LED bulb when lit at 100%, heats up to temperatures >60°C Adjust the print material to the temperatures of your bulb. It is not recommended to use for halogen bulbs - they reach very high…
I made this to improve our home theater experience by blocking the direct light from the bulbs. It made a huge difference! Print with or without the blacked out portion. If you want the blacked out part, then you'll need to do a filament…
GU10 ring for spotlight to keep bulb in place 50mm diameter without “taps” printed with 100% infill
Der entworfene GU10 Ring für die Deckenbleuchtung, ersetzt den original Haltering. Dieser passt ziemlich genau beim “Premium LUX No YC-69Z16”. Für andere Halterungen werde ich noch welche entwerfen. Am Besten erst den Haltering testen, ob…
Deckenbeleuchtung Sonne für GU10. Rinhalterung kann unter dem Modell Mond heruntergeladen werden. Weitere Informationen sind dort zu finden: Mond-Lampe 100mm für Decke GU10 Leuchtmittel mit Haltering
Optional material for this model is PCT-G, due to heat production of lamp, but it also works well with PET-G (maximal measured temperature inside the tube was 50 degree Celsius). Use only LED spot lights up to 4,2 W. In the lower part of…
Sollten die Spheren (bis jetzt, Mond und Sonnenleuchte/-difusor) nicht richtig passen und Ihr einen angepassten Ringe benötigt, schreibt mich einfach an.
Filament: - JAYO - white - PLA+ Objektgröße: ca. L:B:H in cm Drucker: Prusa MK3S Düse: 0,4 Schichthöhe: 0,2 Infill: 15% Stützen: keine Druckzeit: 15min Der entworfene GU10 Ring für die Deckenbleuchtung, ersetzt den original Haltering.…
Filament: - JAYO - white - PLA+ Objektgröße: ca. L:B:H in cm Drucker: Prusa MK3S Düse: 0,4 Schichthöhe: 0,2 Infill: 100% Stützen: keine Druckzeit: ca. 11 Stunden Die Merkur-Deckenlape, sollte mit dem 39,00mm Haltering passgenau ineinander…
