Liczymy pasujące modele…
Originally published here: Xiaomi Redmi Note 10 & 10S m2101k7 case by tato_713 - Thingiverse Some of the models are designed for rigid materials and others for flexible ones. The models materials are not interchangeable , so pay attention…
80mm fan adapter for most AMD MIXXX series GPUs. There is an optional fan bracket that can used if desired, or the fan can be mounted directly to the plenum. The bracket is designed to be used with m3 heat set inserts for mounting the…
camera holder for HBV-3M2111 V22
The bracket is angled so that it points centrally to the print bed (when placed at the top). Mount it to the top right of the tophat and adjust the position before fastening it. You need the following parts: 4* RX-M3x57 threaded inserts…
min 40% infill supports required TPU material
The original knob broke, so I made a replacement as well as an alternate design which might last better. If you like my design, you can buy me a coffee !
For use with wall control pegboard, print with supports (Bed only). This is created based on the system by Luma - https://www.printables.com/model/52618-ddd-printable-wall-control-system
This has slots for 2x6 magnets in each of the four corners. Just add a “Pause Print" at the appropriate spot, and place them in!
Remixed u:rjm2112's nice design to accommodate a couple more colors. Use a high infill like 70% to prevent infill artifacts from showing on the top surface. Print at 0.2 mm layer height. Color change heights are shown in the slicer…
I liked my case for the M21 so much I made another for the Jade Audio JM21 baby brother. It sits in the case upside down for easy headphone port access. As such you might want to get some fillers for the USB C port and whichever audio…
I created a minimalist case for the XH-M214 watering module that is easy to print. The holes for the buttons was intentionally left small, so it can't be pushed accidentally. You can use a toothpick, or something with similar dimensions…
Размеры посадочного места на картинках. Печатал АБС пластиком, заполнение 15 процентов. Можно печатать и другим пластиком, усадки будет меньше, просто садится будет плотнее Подходит для Токарного станка WM210, закручивается винтом для…
Case to hold The FiiO M21 DAP in it's silicone sleeve. With a clip to hang on your waistband. You'll need to modify the clip if you want to use it with a larger belt. Quality PLA should work fine 3 walls 15% infill. PETG might be even…
I've seen several FiiO M21 stands but they all had one flaw or another. Mine is sturdy, using a vertical spar underneath to minimize flex. It also has a captive hold on the bottom of the device so it can't slide left or right. And there's…
Stabbing time Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Supports: Yes Notes: Frame requires supports. Best to print the frame in ABS so the frame lock doesn't lose its springiness. For the blade, print one…
Размеры посадочного места на картинках. Печатал АБС пластиком, заполнение 15 процентов. Можно печатать и другим пластиком, усадки будет меньше, просто садится будет плотнее Быстросменный резцедержатель, AXA QCTP 250-111 250-101 for WM210.…
very simple and small mount for HBVcam 5m2134 v11 there are two version of cam mount simplified - consists of profilepart, camholder 22degree angle fixed - one file
Could be use on any airsoft replicas but its primary intended for m14s. Silencer using M14x1 L thread and M4 screw that could be use to fix the silencer in place. Model is based on period pictures from the war.
Franklin m210 stud finder wall mount
Install around the brass post of the Convoy 20A driver found on the M21B LHP73B flashlights. In theory it will reduce the amount of damage to the battery if the light lands head first. This design is found on some other tactical style…
Cover for Fiio JM21. Reinforced 2mm thick cover with heavy to push buttons to prevent false pushing. There are two options: One has "tight" buttons built into the material. The other has separate, click-in buttons that are more tactile.…
Sturdy angles for mounting a QNAP QSW-M2108R-2C switch in a 10” rack. Takes 1 U of space.
Used to store heavy chuck wrenches that have nowhere to store and have fallen to the ground : ) Embedded magnets diameter 10mm height 7MM to 10X7
My own model🙏🙏🪖 (!!!!NOTE!!!!)before installing on rifle apply a bit of heat for a few seconds to soften the lips then slide optics from the start of the rail to the desired location. Print with pla/pla+ for best results Enjoy the model:)
Case and cover for Fiio JM21. The cover is a bit thin and may need to be reinforced with solvent. Carrying case for the player in its original case or in the included case. Printed in PETG. Case codename: "Domino."
Frame to adapte filter M210 filter to LS1 vaccum. Sorry for the picture, I printed the part in clear PETG :)
I wanted a sturdy box to protect my new Fiio M21 DAP. I designed this to hold the DAP while it's in the factory rubber protector. The logo is flush with the top of the lid if your printer supports multi-color printing. If you place the…
A case and cover for the Fiio JM21. The cover is a bit thin and may need to be reinforced with solvent. This carrying case is for the player in its original case or the included one. It's designed for carrying with a set of in-ear…
Crash pad na nakrętki 21mm, hulajnoga kukirin Różna wysokość Nut 21mm
Info: These supports are designed to fit under an XMG Core 15 M21 gaming laptop and are supposed to improve airflow and ergonomics. I have made no heat comparisons yet. They are sturdy, easy to print and can be put into a backpack without…
Travel case for the M21. Print the case in any any plastic you like but remember if you're going to have it in a summer sun hot car, you probably want to avoid PLA. 2+ walls +15% infill. You'll need 6 M3x18 or 20mm screws for the hinges…
I printed at 0.10 layer height because it still only took 30 minutes at that layer height.
To replace the Hi-Lo gear for an unusual mini lathe
Needed somewhere to store the remote for our Lefant M210 robot vac. We rarely use the remote because the vac is connected to our smart home, but didn't want to lose it and always have it as a backup. So I designed this mount to hang…
A tool that helps to release the engine clutch from the gear. / Ein Werkzeug welches beim lösen der Motor Kupplung vom Zahnrad hilft.
A socket adapter to be able to use a normal 21mm Socket on a 27mm oil filter "nut". Needed this for a 2010 Ford Focus 1.6 TDCI oil filter. Has a hole going sideways through the middle of it to be able to stick in a screw driver for torque…
Compatibility: Milling Machine Dust Cover Category: Machine Tools
Case for Fiio M21. For storage and transportation. May need to be reinforced with solvent. Printed in PETG. Case codename: "Domino."
I made a ring that can be printed from glow in the dark (GITD) filament and mounted inside the head of a Convoy M21K. For me it fits really snugly, might need to use tape if it's easily falling out. Make sure to print using the wall order…
Magnetic mount for the Brady M211 wireless label printer. You will need, 1 x neodymium magnet with stud. I had one laying around that was 25mm OD, 8mm flange with a 6mm stud. I attached the .step file so edit as you need & what is…
This is a tool to remove the bezel on the Convoy M21H. Printed using an Ender 3 V2 Neo with a stock 0.2mm nozzle @ 20% infill in PLA. Source files can be found here if you want to make adjustments:…
Dust pipe for BOSCH GCM216 etc. (input d36 mm) This nozzle is designed to remove dust at a 90 degree angle.
This is the locking lever and safety switch for a Vorwerk Thermomix TM21 a few things you should know if yours broke is that there are 4 small tabs on the metal bar inside of the locking lever when you get your broken lever off (i melted…
Simple box design for your Convoy M21K, there is enough play to store the light with the tailcap ½ turn unscrewed to protect the battery/mechanically lock out the light. You will need 3x M3x35 Screws. I recommend printing the box, lid and…
Install around the brass post of the Convoy 20A driver found on the M21B LHP73B flashlights. In theory it will reduce the amount of damage to the battery if the light lands head first. This design is found on some other tactical style…
Размеры посадочного места на картинках. Печатал АБС пластиком, заполнение 15 процентов. Можно печатать и другим пластиком, усадки будет меньше, просто садится будет плотнее Быстросменный резцедержатель, AXA QCTP 250-111 250-101 for WM210.…
Размеры посадочного места на картинках. Печатал АБС пластиком, заполнение 15 процентов. Можно печатать и другим пластиком, усадки будет меньше, просто садится будет плотнее Подходит для Токарного станка WM210, закручивается винтом для…
Case and cover for Fiio JM21. The cover is a bit thin and may need to be reinforced with solvent. Carrying case for the player in its original case or in the included case. Printed in PETG. Case codename: "Domino."
Case for Fiio M21. For storage and transportation. May need to be reinforced with solvent. Printed in PETG. Case codename: "Domino."
A case and cover for the Fiio JM21. The cover is a bit thin and may need to be reinforced with solvent. This carrying case is for the player in its original case or the included one. It's designed for carrying with a set of in-ear…
This is a larger 55-tooth gear for the Heden M21VE/M21VE-L lens motor, allowing you to dig into hard-to-reach iris gears like the 15/18/135/150/200mm Zeiss Supreme Primes, and modern rehoused lenses from TLS, Zero Optik, etc which have…
One of the stand's of a old Termomix TM21 Print Settings Printer Brand: Creality Printer: Ender 3 S1 Rafts: No Supports: No Resolution: .02 Filament: PLA
Remix of the great model of Pfelpensson. It is the airborne version of the BM21-rocket launcher system, based on GAZ66. Printing barrel pack and mount separate gives most flexibility, but parts are quite delicate to handle. Sized for…
