165 modeli
STLs All files are in correct Z orientation Main (Use one of the following) + main.stl (for ~22.5mm handlebar) + main-short.stl (shorter stem) + main-32mm.stl (for ~32mm handlebar) * jaw.stl * screw.stl Clip (Use one of the following) +…
I got an old scooter from a friend, but the rear mudguard was broken off and missing. I designed this to be as close to the original as possible while still being easy to print. -----Slicing----- Because this model is too large to fit on…
I was using one of the other anti vibration pads but they kept falling off, and I keep losing them. This design uses the main screw to keep it all in place but requires a 5mm hex tool to remove the screw, but it takes less then 5 minutes…
Fairly form fitting to the wheel's contour to minimize stress, it has just enough wiggle room to get on and off without a problem. I'd recommend trying to remove them once you have one side of the tire out, otherwise they are effectively…
Sturdier tha others and printable without support. NEW VERSION. With ears for better fixation.
Rear fender replacement for Xiaomi M365 scooter. This part is both stronger and lighter (160g) than the original one, though I did manage to break it after a while, so consider using one of the aftermarket fender supports. Print Settings…
Just a mix of deferent xiaomi fenders Print instructions Print with supports
This protects the cable connector in the rear of the scooter from being damaged over time. I just glue it in.
Necesita soportes, es un poco más corto que el original EDIT: v2: se ha ajustado la distancia del enganche para el gancho de pliegue, debería quedar similar al original. - hook position fixed LICENSE: NON COMMERCIAL prohibida la venta de…
Designed specifically for the Doc Green ESA 5000 (Xiaomi M365 / Pro clone) E-Scooter (periodically sold by Lidl) but potentially compatible with the Xiaomi M365, Pro and Mijia versions too (no guarantees however). These Vibration…
Hook for the Xiaomi M365 Print Settings Printer Brand: FlashForge Printer: Guider II Rafts: No Supports: Yes Resolution: 0.15 Infill: 100 Filament: PLA eSUN Category: DIY
A clamp for Xiaomi M365 electric scooter. Fits all "Just Why Design" gadgets. Three M4 and two M6 screw sets and 3M double side sticker should be used during installation.
ISO 4017 Bolts M12 - M36 / Length 25 - 200
KEY BENEFITS: no need to remove the wheel for installation no need to readjust brake disc no need to change the original screws (just add 1XM3 10mm and 1XM3 nut) no need to modify the original rear wheel cups suitable for 8 and 10 inch…
No Supports is needed. PETG, 4 perimeters. Original from: https://www.thingiverse.com/thing:3190522
Soporte para fijar el guardabarros del xiaomi m365. ( Para imprimirse necesita, al menos, colocar un soporte en la parte más alta, donde engancha con la luz del guardabarros) Xiaomi Mijia M365 Mudguard Bracket (needs at least 1 support in…
A Stand i designed to have my scooter stand up somewhere without drilling holes into the wall to hang it.
This is a M36 threaded bolt. You can scale it to the size you need: 133,3% – M48 116,7% – M42 100% – M36 83,3% – M30 66,7% – M24 55,6% – M20 44,4% – M16
3 models of xiaomi m365 pro or pro 2 scooter hooks (it will probably fit other models) the first is a slim version for light luggage need 14mm screw with flat head second one (strong) needs a longer 20mm screw with cone head and you can…
A replacement rear wheel nut cover that also fits an AirTag. Fusion 360 file is provided so it can easily be adapted for newer Xioami scooters. Print in picture was printed with 0.6mm nozzle and PLA. If scooter lives outside, PETG or…
Broke my front mudguard (by over tightening the screw) after replacing my front tire. Definitely needed when driving through the rain! Position the model on it's side on the build plate. Support on the wheel side probably isn't necessary.…
I Realy Love The model from Pirateln3D an i Realy Love the Apple AirTag. But if you Put the AirTag inside the scooter, it will not work. The metal Blocks the Airtag. If you make a special case for the AirTag, anyone will see it and can…
Xiaomi M365 back fender support for 10 inch tires. If you found this useful, please donate what you think it is worth to my https://www.paypal.me/Aminokislota . Help cover the time of design. Thanks, Enjoy! Category: Other
I have broken my one. So I made it in Fusion 360. Added V2 with increased outer ring for 0.2mm and tab for easier opening Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 100…
I've created a mount for a U-Lock for my Xiaomi M365 scooter. The diameter of the lock rod is ~14mm so the hole is 14.5mm. You need 2x M3x10mm Socket Head Screw and 2x M3 Nuts. Print with PETG for flexibility & strength. I've added the…
What's this? This is my custom wallholder for a Xiaomi Mi M365 Scooter, including space for the powersupply. I wanted to create a design which doesn't look too bad, is able to securely hold the scooter and also doesn't need a ton of…
Because this ring alrady broke twice I created a more stable version myself. In my opinion It is much more stable than the original. The original tapers slightly downwards, which I have not implemented because it is not necessary. Print…
I printed mine in polycarbonate with 5mm wall thickness and 35% infill. I have not tested any other material.
A holder for a 0.5l bottle (64mm diameter) from "Just Why Design". You will need one "universal clamp" - https://www.prusaprinters.org/cs/prints/40227-xiaomi-m365-universal-clamp - to mount it on your Xiaomi M365.
Intake Funnel with ø62mm inner diameter. Source files included. For Mikuni VM36-4 as sold by Kedo.
I took the already great idea and improved it in the following aspects: 1. Added two clips, meaning you no longer need to glue the part onto the scooter. This works best with PETG, since the clips are very strong and springy then. 2.…
Remixed this fender hook for my Xiaomi Mi M365 Pro (will work with standard M365 too) with Fusion360 to be mounted with M5x20mm bolt and M5 "nylock" nut (so it doesn't come loose). My original hook got ripped off the fender (original bolt…
It need to be printed with a flexible material like TPU
Model to mount NEM362 coupler on Marklin 3064 or equivalent
This adapter adds bulk to the screwcap of the pump extension supplied with the Xiaomi Mijia M365. The extra purchase allows you to twist it on and off more easily, keeping more air in the tire when disconnecting. DESIGNED TO BE PRINTED in…
This is the left cover for the front axle for the M365 scooter. Category: Sport & Outdoors
More durable cover than stickers.
Use this plug to fill the valve hole after you change stock tires for the solid or honeycomb tires. Print instructions Print this with 2 perimeters, 30% infill, layer height 0.2mm and use TPE or some rubber material.
Adapter na 3/4" hadici, šroubovací průchodka M36 Vrtám díru 40mm, tloušťka stěny nádrže je cca 3mm. Doplnit ploché těsnění s vnější strany , závit netěsní na 100%. Z vnitřní strany není nutné těsnit. Hadici před nasazením nahřát, aby…
Flexible filament only. LICENSE: NON COMMERCIAL prohibida la venta de modelos sin permiso del autor // the sale of parts without the authorization of the author is forbidden Category: Vehicles
Keeps the standard mi scooter display protector from falling off and shifting around
ENG Expansion board mounting bracket for xiaomi scooter M365 (all versions / PRO / S1 / ....). The board can be made or bought, for example, from berryboards 2 files for M5 or M6 screw I have tried that 4 pieces are enough to attach one…
Exact copy of the original. You will need the nut and screw from the original to use it. Better to print with 100% infill
I use 10" tires and there's limited space between front mudguard and the tire. Designed a flap that can be attached from the outside and without any tools. Holds in place with friction and is pretty snug, depending on…
With this practical hook for the Xiaomi E-Scooter, you can always carry your luggage safely. The accessory is compatible with the Xiaomi Pro 2, Pro, M365, 1S, and Lite and can be easily attached. Use it to transport your bags, backpacks,…
Configurable for up to three single or double cables. The stl files are for an additional 2 x 2.5mm² (14AWG) cable (external battery pack) For Xiaomi Mija M365, 1S, Pro2 and similar E-scooters. Use soft TPU filament.
Xiaomi Mijia m365 Fender Bolt Caps
C’est un cache de batterie et remplacement pour la m365 pro et modèles. Compatible dans le cas où il n’y en a pas ou il est trop endommagé. moi, je l’ai fait en pla mais vous pouvez le faire dans differentes matériaux soit resistants aux…
Front wheel nut bolt and power cable protection cover for the Xiaomi M365 Pro front bumper.
Simple side stand riser for scooters like the Xiaomi M365. Rises around 20 mm high, perfect for scooters with extended front or rear bumpers. Three m4 20mm screws with nuts are required.
Since I like more rounded shapes and more contained lines, I made some small changes. Increased screw housing and side t
Print from the side. v3.2-> Fixed the light holes and perimeters. // corregidos los agujeros de la luz y los perimetros superiores LICENSE: NON COMMERCIAL prohibida la venta de modelos sin permiso del autor // the sale of parts without…
Xiaomi m365 rear wheel side cover - Tapa lateral rueda trasera con agujero Category: Sport & Outdoors
Another hook for the Xiaomi M365 (it should work with the trottmi and other clones as well). @Magnetik_206574 tells us it's compatible with the Motus Scooty 10 lite. Advantages: it uses only one mounting hole, so that the handlebar is a…
Sturdy wall hook for Xiaomi M365 scooter with space for charger and cable hook. All three parts are printed without support. The only place where support is needed, I have already put. After printing they are removed. I recommend to use…
End caps to assist with cable management of the charger for Xiaomi M365 E-Scooter Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: amazon basics PLA Category: Electronics
i use PetG filament for this part Category: Other
Printed on MK3S+, with PLA+. Can easily withstand the weight of a filled grocery bag
Xiaomi M365 / Pro2 rear fender for 10 inch, 8cm wide tire Printed on Creality k1 max (300x300 bed) Slicer will ask to rescale it at first but select no, and rearange the part to fit the bed. Printed at 0.4 mm nozzle PLA (Abs recomended)…
Riding my Xiaomi Mijia M365 electric scooter for longer than a few minutes quickly made my thumb a bit numb. While I am fully aware that this scooter has cruise control, I prefer having full control of the throttle at all times, so I…
Phone Mount for the Xiaomi M365 / M365 Pro designed for the iPhone 6/7/8 with a case. Hardware needed: 2x M3x8mm Socket Head Screws 2x M3 Nut I've added the Fusion 360 files if you want to edit the design :) Print instructions PETG 3…
Sport front mudguard for all Xiaomi models of electric scooter.
Charging Connector Cap For M365
usefull accessorie for foot stand after shock absorber modification
Secure charger case for Xiaomi M365, M365Pro, Pro2, Essential, 1S, Scooter, Scooter. Design intended to be suspended on the handlebar (handle, axis or bell). If the charger is to be put in a place of passage, install the charger after…
rear mudguard without light for xiaomi M365 with ULIP suspension
Rosca M36x1.5
in order for the 10 inch wheel to fit, i had to mount the wheel a bit lower. but the reflector cap did not fit anymore,
I made a better wall mount for M365 and M365 Pro. It's made for small printers like a Ender 3. I hope you like it. The scooter is resting on the front wheel and handlebar/light. Please comment what you think. :-) Print Settings Printer…
Adapter to go from the later version of the DJI tripod thread (m36-3) to US surveying thread (5/8"-11). Please print with PETG and keep in mind this is plastic and is not as strong as a metal equivalent thread adapter. 3MF file has…
Für selbstgemachte Rollcontainer habe ich Schubladengriffe gebraucht. Thematisch sind Schrauben hier bestens geeignet. Der Griff besteht aus einem Befestigungsteil in Form einer hohlen Gewindestange M36. Der Griff eine Mutter M36 mit dem…
Tesnenie na vylagrovany klb riadiacej tyce.
I needed a luggage hook, but also a hook for the chain lock. The opening for the chain lock (U-Lock) is 25 mm. Hardware needed: 6 pc M3x12 screw DIN 912 6 pc M3 nuts DIN 934 4 pc M3 nuts DIN 934 (for future upgrade) I used PETG, but I…
I charge my E-Scooter in my Homeoffice and didn't want to have the powerbrick lying on the floor. So I designed this small mount for my desk to have it away from my roomba. Can be printed without supports. Material: PLA Printer: Prusa Mini+
Front cable protector for Xiaomi Mijia M365 Scooter LICENSE: NON COMMERCIAL prohibida la venta de modelos sin permiso del autor // the sale of parts without the authorization of the author is forbidden Category: Vehicles
I crashed my scooter and broke the original screen cover and so I made one. If you want to replace yours too I'd recommend getting a very good first and second layer on both prints. I had to do a lot of postprocessing to fix my mistake.…
A lock mount fo the M365 scooter. Used M4 screws and nuts to secure in place. Category: Automotive
Model replicated from the original, the threaded nut needs to be glued. I recommend printing with ABS and looped 2 walls
I had the cable break clean off when the rear mudguard broke. I replaced the mudguard and soldered in a connector but still wanted to protect the cable. This screws in between the scooter and the mudguard and will keep mud away from the…
This is cap for xiaomi mijia leg. Print it from flexible material. Category: Sport & Outdoors
A replacement rear wheel nut cover with a hidden compartment for Silver Monkey SMA193 AirTag alternative (rebranded mili mitag hd-p16). Best to print on the visible side down, no supports needed. Installation Remove reflective sticker…
Xiaomi_stand ( M365, Pro 1, Essential, Pro 2, Scooter 3)
A very common repair is a missing or broken knob. You might know the proper threads, or even have a proper nut in the junk drawer, but to dress the nut up into a proper repair, you might want a nice handle to wrap around the nut to make…
Front fork bearing cap and holder for rotating stopper. I printed my with PETG.. Dimensions islike original part, you can make side walls higher or bigger radius for more rigid version. Only base need to stay same.
Xiaomi Mijia M365 front GoPro Mount Better in PETG Need Supports LICENSE: NON COMMERCIAL prohibida la venta de modelos sin permiso del autor // the sale of parts without the authorization of the author is forbidden CHANGELOG: v7…
An eye from "Just Why Design" to be mounted on your Xiaomi M365 scooter. It is ment to be used with a strap to carry your scooter. You will need one "universal clamp" -…
Проставки для m365 под 10 колеса.
Mount for this headlight: https://aliexpress.ru/item/33014445820.html Does not interfere with Monorim front suspension. Single M5 screw and nut required (washers are optional). Everything else comes with the headlight package.
here is a disc protector with integrated light for xiaomi M365 for ULIP suspension only.
Patient: Xiaomi M365 Pro Disease: Broken mounting of front mudguard Cure: 3D print, 2xScrews, Hot Glue Skechup file - included Post-Printing 1. Break your mudguard 2. It's bad :( 3. Print a part. Put 2 x screws 4. Should be like this 5.…
I made this cover, to avoid small stone/debris getting inside the tyre that might cause a flat tyre. Correct airpressure is what I think causes most flat tyres, but this could be a soft spot too. Atleast on my m365, there is a lot of air…
Xiaomi M360 Soda Holder One version have thinner walls, recommending to use the thicker wall version. (You cannot fold it with the holder there, i need to redisign it a little.) Will upload a new version soon. Print Settings Printer…
Ganchito con una entrada más fina para que no escapen las bolsas con las vibraciones..-> Mejor imprimir en PETG, ->IMPRIMIR DE LADO para mayor resistencia, haciendo que la primera capa sea un lateral. LICENSE: NON COMMERCIAL prohibida la…
Charger port protection for M365 Pro
PLA will melt, PETG is recommended Put the adapter on and screw it in with 1 screw, then put on the ceiling
The holder's design integrates with the style and looks of the original parts of the scooter.
