50 modeli
This fan shroud allows you to mount a 40mm fan to cool your NEMA 17 extruder motor without blowing air on the bed or printed parts. It's specifically designed to fit on the MakerFarm Prusa i3 and i3v, but it should fit any printer that…
* UPDATE: a hardware kit is now available! * click here I am proud to present the Itty Bitty Double Extruder, a two-material belt-driven extruder with mounting hardware for MakerFarm i3v printers. Versions are provided for 3mm and 1.75mm…
Update: Added extra-long version for use with stock fan. This 40mm fan shroud and mounting bracket allows you to mount a fan to cool the print when printing with PLA. It mounts to the existing holes in the MakerFarm variant of the…
Replacement e carriage for the Makerfarm i3v to mount the e3d Titan extruder. V1 with shim for most steppers, V2 includes shim distance (3mm) for e3d pancake stepper.
Makerfarm laser cut wood doesn't hold the Z nut in place effectively leaving backlash and will potentially lose z alignment entirely if bumped. This locks the nut into place and prevents both of these issues.
This is the third evolution of the Itty Bitty Double Extruder. NOTICE: Version 2.1 released. See notes below. * A hardware kit is available; links below. * New in this version Better flexible filament control Supports Hexagon AO Designed…
I have searched for a good cooling fan for my printer since I have auto bed levelling but couldn't find one to fit my printer so I made this one I think it works great. I added obj file for Slic3r because someone told be that STL file has…
This is a drop-in replacement for the stock MakerFarm Prusa i3v X carriage mount that adds an additional eccentric on one of the upper wheels. This allows the entire carriage plate to be tilted left and right to level dual extruder…
UPDATE: Added longer version of Z probe for longer hot ends. This replacement X carriage bracket and switch arm allow you to mount a servo-actuated Z probe to your MakerFarm Prusa i3v printer. The Z probe serves two purposes: it registers…
The new MakerFarm Prusa i3v printer (with the aluminum V-Slot extrusions) is solid and smooth, but the end-stops leave a little to be desired. The Z stop requires splitting the wood and is still difficult to get aligned to engage the X…
Remixed version of https://www.thingiverse.com/thing:145065 with increased width to accommodate a 80mm fan. NOTE: It will be tight under the stepper motor, but it will fit. Just. Print instructions NOTE: It will be tight under the stepper…
Here are the parts I use to manage and hide the wires on my MakerFarm i3v printers. The cable clips snap into the grooves of the V-Slot extrusions to hide wires inside. The end strain relief mounts to the end of an extrusion with a 5mm…
* There is a newer version available here: Itty Bitty Double FLEX V2 Extruder * The Itty Bitty Double FLEX is the second iteration of the Clough42 Itty Bitty Double Extruder. This new version is designed to accomodate flexible filament…
Note: there are two versions of the switch bracket. Choose the longer one if you have the newer endstop switches with wheels on the arms. Note: this part fits the 8" i3v. The 10" printer has longer X extrusions that block the screw unless…
Designed for approximately 18cm diameter inductive sensor ( http://a.co/9wMezOl ). Uses the existing 15mm M3 screw on the X carriage. Print Settings Rafts: Doesn't Matter Supports: Yes Category: 3D Printer Accessories
Mount for a radial fan (XYJ05S5015H) for part cooling on a Makerfarm i3v (10"). It is mounted on the two hotend screws, on top of the hotend fan. This fan provides a lot of air, so a silicone sock on the original E3D v6 hotend lets you…
This is an OpenScad parametric design for a screw based micro adjustable Z stop for the Makerfarm's Prusa I3v. It works great on my machine but if you want to change it just tweak the parameters and recompile in OpenScad to generate the…
Note: there are two versions of the switch bracket. Choose the longer one if you have the newer endstop switches with wheels on the arms. Note: this part fits the 8" i3v. The 10" printer has longer X extrusions that block the screw unless…
The MakerFarm Prusa i3 suffers from the same ailment as most Mendel variants: the Y axis is noisy. The combination of the linear bearings on rigid rods with the bed stack of wood, heat bed and glass causes a loud, buzzing resonance at…
I never printed it (yet). Print Settings Rafts: Doesn't Matter Supports: Yes Category: 3D Printer Parts
This upgrade is good to make your printer quieter. The difference is noticeable. I used M3 5mm screws for screwing the dampener to the motor and you can reuse the screws that are used before to screw it to the 3d printed model. Here are…
These parts allow you to mount a Raspberry Pi camera with LED illumination on your MakerFarm Prusa i3v to observe the bed of the printer. It's perfect for use with OctoPrint on a Raspberry Pi as a network printer controller. The bracket…
Replacement plate to allow the installation of basic delrin nut blocks on a leadscrew upgrade for a Makerfarm I3V. While not a complete solution, this allows you to continue to use the back plate that holds the other end of the idler…
Adding this thing to the corners of your Makerfarm's Prusa I3v hotbed simplifies the hotbed leveling. It prevents the lock nut from rotating so you can use one hand for the hex wrench and the other to check the height with your shim of…
This is a new X endstop mount for MakerFarm i3v printers to extend X travel further to the right. This allows the left extruder nozzle on dual extruder setups to reach more of the bed. On the 12" i3v with the Itty Bitty Double Flex…
This knob was made for easier control on the LCD for the MakerFarm Prusa i3v. UPDATE Shortened knob overall to keep the knob from interfering with button pressing. Category: 3D Printer Accessories
Wanted to change from the 4 line smart controller to the full graphic. Used modelatolyesi front and the brackets from ogelybogely http://www.thingiverse.com/thing:166119 and mashed them together. You can print the knob and back from…
There's a few ATX mounts for the i3v out there, but they were either far more complicated than necessary, covered the side fan on the PSU, or mounted on the too-crowded RAMPS side. I wanted to mount it in the area intended for the PSU and…
Modified the arm that sits on the front face for supporting heavier weight. Printed out pretty good and supports the weight of at least two 1KG spools no problems. Category: 3D Printer Accessories
I am using these clips to prevent the Z nuts on my prusa i3v from coming out of their nut trap. This make sures that the the two z elevators stay in sink. The clip provide a few millimeters of vertical play in case your z stop is too low…
(To customize this design click on the Open In Customizer link here) This bracket is attached to the left side of stock Makerfarm Prusa i3v extruder and it is used to cool the workpiece layers before printing the next one. This improve…
This improved cooling system for the Hexagon (NOTE: NOT Hexagon AO) hot end on the MakerFarm Prusa i3 and i3v mounts the fan behind the hot end to keep it out of sight and out of the way. It also directs the cooling airflow away from the…
The MakerFarm Prusa i3 and i3v instructions call for the LCD to be mounted to the frame with four M3 screws. If you tighten these screws down, they cause the PCB to flex. If you don't tighten them enough, they rattle and vibrate loose.…
A merge of my X carriage design with russiancatfood's VORON extruder. Includes servo for bed leveling probe and blower fan mount. Category: 3D Printing
Modified to work with longer E3D Volcano hot end. Designed for approximately 18cm diameter inductive sensor ( http://a.co/9wMezOl ). Uses the existing 15mm M3 screw on the X carriage. Print Settings Rafts: Doesn't Matter Supports: Yes…
http://www.thingiverse.com/thing:326641 modified to be 98mm long for spool holder extension. Category: 3D Printer Accessories
It's called a dustcover, but I made it to keep my fingers off of the board while I'm using the knob. Print solid with the top down. It does not go all the way to the top-outside edges to allow for the screws. The island in the middle…
A slightly modified version of clough42's version giving a little more support for both single wall and double wall thickness of the MakerFarm Prusa i3 and i3v. Completely redrawn in SketchUp, source files attached. Uses these sorbothane…
I love my Prusa i3V but the stock spool holder leaves much to be desired. It obstructs the access to the SD card, it makes strange noises with some spools replacing spools is a hassle due to the design of its cross member and its height…
Just a simple adapter to use bowden on MakerFarm i3V Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2 - 0.3 Infill: 20% or more Filament: n/a ABS Category: 3D Printer Parts
Remix of clough42's Sorbothane isolator foot ( https://www.thingiverse.com/thing:322915/ ). Made to be printed with flexible filament instead of purchasing the Sorbothane bumpers. Version 2 added with clough42's original design for slot…
A servo holder for auto bed leveling on the MakerFarm Prusa i3v, which has a new nut trap and different back tab placement than the MakerFarm i3. Based shamelessly on measurements from http://www.thingiverse.com/thing:193893 and special…
Tired of listening to your 3D printer buzz and vibrate its way through another print from the next room? These plastic feet allow you isolate your printer from the surface it's sitting on, quieting it considerably. UPDATE: Added a version…
A collection of MakerFarm i3v remixed and modified parts. I liked the knob, but wanted the dimple for pushing. Added the anti-rub groove to the extruder and a lip for the front bearing, keeping the rest of the stock extruder. Included my…
I recently started using Octoprint, and Octoprint uses a simple web interface. I have some old Android tablets collecting dust, and they can control Octoprint just fine, so I printed up a pair of little clips to "attach" one of the…
Tried http://www.thingiverse.com/thing:612584 , did not like. It was awkward to assemble and knocked about 10mm off my Y travel. This is as simple as adjustable gets. Put a couple M3 nuts in the forward slots. Ideally, you'd leave a…
Logitech C270 camera bed mount to accommodate my own requirements for the printer. Print Settings Printer: Makerfarm Prusa 8" i3v Rafts: No Supports: Yes Resolution: 0.2 Infill: 25% Category: 3D Printer Accessories
This is a rail mounting, extruder carriage for converting the Makerfarm i3v to a modular i3 Rework style carrier. Scaling is a bit funny when I import it to Simplify, scale up by 10.1 for proper dimensions and rotate for printability.…
I was using a RAMPS cooling fan with this bracket , which works just perfectly... until you need to mess with the RAMPS board and wiring. This is a simple clip-on fan mount which snaps onto the plywood with just barely enough clearance…
This little tool make it easier to change filament. Pull the extruder tab with one hand, insert this tool as shown in the picture and release. Now you are free to remove or insert a filament. Remove the tool before printing. The default…
