Liczymy pasujące modele…
Battery door lever for the Olympus E-M5 III because it keeps breaking for everyone!! Remixed from @myxfit_28243 's model to fit the E-M5 III instead of E-M5 II Notches are raised by 0.5 mm to accomodate the locking lug + spring see pic 4…
Two handy belt clips for Olympus camera batteries types BLS-1, BLS-5, BLS-50. I use three different PEN camera's which are just great for street photografy but the batteries do not last very long. So I designed these belt clips to…
I made this to help the battery last longer in your Olympus 35 SP - by covering the light meter, the amount of battery drain is minimised. I used some sticky-back tape to stick it to my camera. The door is inserted from the back - the…
Eyecup and accompanying dust cap for the Olympus BTHU2 eyepieces (Olympus WK 10x/20L). I used 95A TPU and it works fairly well. Probably would be nicer in a less stiff and matte textured material. The dust cap fits securely, but is still…
I had this printed at Detroit 3D Manufacturing via Craftcloud in black PETG at 60% infill (to give it some weight). I have the original E10K (micro-USB), but there is a newer E10K-TypeC (USB-C) which I have not tested, but I believe it is…
I needed one so i remixed this. You have to remove the original stuff to put this one
A rough cutting guide for replacing the light seals on an Olympus Pen D2 , it might also work on other pen models. This template eliminates some of the guesswork and should ensures light-tight camera. Recommended Tools: Best used with a…
Don't print the cap in white filament, lol, the design isn't thick enough to completely block all the light. Dark filaments should be used. I'd recommend just sticking with black filament.
About the design This is a very compact arca-type tripod plate and bottom strap connector designed to fit the Olympus C-5050 zoom. Note - I have an alternative version of this now, which is a bit thinner, has a bit wider base, and a more…
This is a simple lens cap for some of the Olympus pens. It doesn’t fit the original Olympus pen or the pen S. I haven’t done a lot of multicolored printing, so it’s possible that you could fill in the letters completely. However, with the…
Unlike my E-PL6 the Olympus Pen E-PL3 comes without a front grip. So I designed this camera grip, which I found to make an improvement on handling the camera. Looks better too I think. Printing Print with brim if necessary. I printed with…
For using older Olympus lenses on modern mirrorless cameras
I created this filter case to protect my filters for my Olympus 14-42 len (40mm wide). Printed in PETG with Z seam randomized to avoid that annoying vertical line when the printer begin every layer in the same point. It seals properly and…
Overview Holder for Olympus E-P7 camera with 14-42mm kit lens. Attaches to Honeycomb Storage Wall (HSW) with 4 M3-nut inserts. Cameras lides in from top, right-hand grip facing up. Compatibility Requires HSW M3 nut inserts (included in…
Simple grip to go on OM-D E-M10 Mk.II. Use double-sided tape to stick it on. Two versions available: Non-textured Textured Used bumpmesh.com to apply texture effect. Settings: Displacement Map: Voronoi Scale U: 0.4 Smooth mask: 1 Bottom…
About the design This is another very compact arca-type tripod plate and bottom strap connector designed to fit the Olympus C-5050 zoom. After using my first design for the C-5050 for a while, I liked how it matched the angle of the…
Update 8/2/2025: After using this for several months and feeling like it looked slightly off, I re-measured and discovered that the rotation was off by about 1 degree 🤦. I've uploaded version 0 2 9 .stl's and blender files here which fix…
This is my latest attempt to make things watertight for recreational scuba diving. I used most of the knowledge from my previous article and summarized everything in this video: Consider your skills before you start working on this…
The lever on the battery door of my Olympus em5 mkii broke, so what's a guy to do? Why, model a replacement, of course! I'm not sure if other Olympus camera bodies use the same lever or not, but it works with the em5 mkii at least.…
Simple olympus teleconverters cover (tc-20 and tc-14). It's little bit deeper than normal covering cap
Remix of adrian057 lens cap to subtract the Olympus font from the object. This makes the part easier to print without support and also looks great! Original post: https://www.thingiverse.com/thing:2737337 "This is a lens cap for the…
Original eyecup and remix source kept snagging on stuff. These models only slightly protude from the viewfinder. Print it in TPU.
Thought this was gonna be a massive pain to make but it was actually nice and simple Expect a dummy battery shortly
Convert an Olympus OM lens to L mount. No supports needed
universal slide holder for olympus BH2 microscope. may work on other models with a mounting hole distance of 36mm.
it's a combination of an Olympus OM lens mount adapted to a Nikon F lens mount that i whipped up for my nikon d3000… there is two different versions included with slightly different mounts. i used version 2. i got it to fit with a little…
Two sizes, needs support. Printed with TPU. Photo shows the compact version.
Lens hood for M.Zuiko Digital ED 40-150mm F4.0 PRO
A replacement for the original LH-49B Lens Hood by Olympus, as far as I know it is only used on the Olympus 25mm f/1.8 lens, but the mount should be compatible with the 60mm f/2.8 macro lens from Olympus. You can use the step file to edit…
Used to mount in the cockpit of a Piper Archer 28
Recalculated adapter for Olympus PEN-D (32mm lens) Added screw, that can be glued in place. Bottom part is made to fit steel threaded tripod mount from zenit (or some other camera, not sure). Oryginal bottom part would fit also. untested…
Battery door lever for the Olympus E-M5 III because it keeps breaking for everyone!! Remixed from @myxfit_28243 's model to fit the E-M5 III instead of E-M5 II Notches are raised by 0.5 mm to accomodate the locking lug + spring see pic 4…
I bought a used camera, and it was missing the rubber grip for the thumb. But that wasn’t a problem—I designed a model of the right size and 3D-printed it using soft TPU. I attached it with super glue. It’s been four years now, and the…
A battery case for storing a pair of batteries. Three options to suit: BLX-1 for the Olympus OM-1 and OM-1 II BLH-1 for the Olympus E-M1 mk2 and mk3 DMW-BLK22 or DMW-BLF19 for the Panasonic G9 or G9 mk2. Uses a pair of 10x3mm magnet to…
The display case is inspired by an idea of what Mount Olympus in Ancient Greece would look like and is therefore for the most precious items that you want to display. The files allow for it to be built as either a watch holder or as a…
This is a Gridfinity-compatible holder designed to store and organize 2 BLS-5 batteries securely. Perfect for photographers or videographers who want to keep their batteries neatly stored and accessible in their workspace.…
This lens holder is designed specifically for the Olympus XA rangefinder camera. It accommodates a 43mm filter, which minimally obstructs the lower portion of the viewfinder, ensuring accurate framing while taking photos. The design…
Lenscap for Olympus Trip35 or PEN There are two versions, one is the conventional and the other will cover the selenium cells only. Category: Camera
This 3d printed part is complementary to Carl Hunsinger's instructional video on adding a T2 camera mount on your Olympus BH-2 trinocular microscope (below). It replaces the MTV-3 adapter and the other 3d printed part in Carl's video. It…
Two handy belt clips for Olympus camera batteries types BLS-1, BLS-5, BLS-50. I use three different PEN camera's which are just great for street photografy but the batteries do not last very long. So I designed these belt clips to…
Desk mount with 4mm screw holes for the FiiO E10K Olympus 2. I used some 3.5mm wood screws Print with a brim if it doesn't stick to the bed.
I hated the fact that I had to carry my Olympus 25mm and Olympus 45mm lenses separate from my inspire 2 case (including the X5s camera) as there was just no place to put them inside the inspire's case without them rattling around inside…
needed a balancing ring for a 25mm Olympus lens to mount on a x5s inspire 2 camera form dji. so designed a lens hood and bayonet fitting for the 25mm lens, which weighs around the same as a balancing ring resulting in a balanced gimbal
Modified Version of the Lensecover with an attachment loop to put a line through and attach it to the camra.
A cap für the phototube on the Olympus BH2 trinocular with the NFK eyepiece inserted. If fit is to loose just scale it down 0.5 - 1%, I got the best results with 0.2 mm layer hight.
Cap for Olympus Microscopes (BH; BH2, CH; CH2) Viewing Head Port
Lens cover for the Olympus PEN-F analog camera. Modelled after the original metal cap. It can be printed in two ways: The "F" facing up - depending on your printer, supports may be required Cut the model in half at around 5mm, with the…
Gear Rack Replacement for Olympus BH2 Microscope Stage Over time, the racks on the Olympus BH2 microscope often crack and lose teeth, so I have designed an inexpensive replacement. It is best to print with a 0.2mm nozzle and 0.05-0.1mm…
A model of the rubber ducky floating in the satyr pool up on Mt. Olympus.
Diffuser for the built-in pop-up flash on the Olympus OM-D cameras. Tested to work on OM-D E-M10 II, will probably fit other as well. Just slide it into the hot shoe and fire away. Can be taken on/off with flash either up or down. Print…
This is a TPU case to hold an audio recorder to a car at speed. Made for use with Velcro straps to a pole. Untested and probably stupid, will go to remote mic and sock later.. {{Now used, and works great to rear windscreen wiper, with…
This is an adapter for the Olympus IMT-2 inverse microscope to mount a Canon EOS DSLR to the camera port. In the images attached it is printed in white PLA but I do recommend black. It features a 34 mm UV filter as a protection to keep…
A stage insert for the Olympus IMT-2 inverse microscope. It features a cutout allowing for clearance of turning microscope objectives. Do not have the original but from what I can tell, the cutout is larger than in the original metal…
Ich bin günstig an eine Olympus PEN E-PL3 gekommen, wollte mal das M43-System ausprobieren. Die Kamera ist schon ganz schön ordentlich, doch sie liegt nicht besonders gut in der Hand. Deshalb hier nun ein Handgriff, der die Sache deutlich…
A multi-part model of the famous classic Asahi microscope, the first microscope manufactured by Olympus in Japan, in 1920. The design uses internal connecting rods that the individual cylindric parts are slid on akin to beads on a rope.…
A smaller and more satisfying to use version of the original Raynox universal clips, specifically for the widely spread Olympus 60mm f/2.8 Macro lens. @Ferdinand_173643 has designed a beautiful Lenshood (Thank you! <3), which I remixed in…
This model is a thumprest replacement for the Olympus PEN Lite E-PE3 camera. In the case the thumprest desintegrates the part can be printed and glued on with elastic superglue or a glue which sticks to metal and plastic. The part is…
Буду рад получить обратную связь. I will be glad to receive feedback.
Bring the magic of Greek mythology into your home with this unique decorative piece inspired by the twelve gods of Olympus! This versatile design offers two options: build an atmospheric lamp that exudes the power and splendor of the…
This is a replacement cover for the flash sync socket of the Olympus OM1 / OM1n film SLR camera Print with the flat face down on the build plate
Modified to print on the left or right side to add strength as suggested by @orthodes
⚠ Commercial Use Notice: If you intend to sell physical prints of this model, please purchase the licensed version here: 👉 Buy the commercial license on Etsy 🔒 License Terms: This model is for personal use only. Commercial use (including…
The lower front needs to be heated enough to be able to bend out slightly, due to its curved shape.
Overview Tired of misplacing, dropping, or fumbling with traditional lens caps? Meet the Iris Lens Cap —a fresh take on lens protection, designed for the Olympus OM-D series (and compatible lenses). This cap uses a mechanical iris…
🔒 License Terms: This model is for personal use only. Commercial use (including selling physical prints) is not allowed unless you purchase the licensed version from the Etsy link below. 👉 Buy the commercial license on Etsy 💖 Want to…
This is an customizable LED-ring light adapter which makes your old Olympus VMT steromicroscope bright and shiny. Materials (BOM): LED-ring light with 3 screw attachment points 2 - 3 x M4 screws, length 16mm, pitch 0.5 for upper mount to…
Used for blacking out the meter on the Olympus 35 SP 35mm film camera. It leaves the rangefinder patch, bright lines, and meter window unblocked so you can still see those through the viewfinder. Clips in place so it doesn't fall off in…
Bumps align with the notches on the battery and a spring holds it firmly in place. The battery model is embossed on the back for easy differentiation from other models. I printed this in PETG-CF and it worked; I would recommend a PETG, as…
Bumps align with the notches on the battery and a spring holds it firmly in place. The battery model is embossed on the back so it can easily be differentiated from others. I printed this in PETG-CF and it worked; I would recommend a…
A small and portable macro flash diffusor for the Olympus 60mm f/2.8 macro lens that attaches on the bayonet mount of the lens. It allows you to still attach filters and close up lenses. It also fits the Olympus 25mm f/1.8 lens, as they…
Printed with ABS like resin, but this would probably also work for FDM. For support on SLA printers I tilted the object ~30 degrees , and added supports
Whenever a microscope is not being used for a longer period of time, the grease in the focusing mechanism dries out. With the added resistance, the first gear to fail is this one, the one mounted on the long shaft. Printed mine in PLA-CF.…
Remix of the Olympus E-M1 holder, can fit E-M1 mark ii, Nikon Z6
Many thanks to @bostandesign for the original design. I really appreciate your work. I added a cutout inside the column to discreetly store two spare batteries. Now, you'll always have spare batteries on hand when the original ones run…
Blade Sword of Olympus from God of War to be printed in parts. This design has these STLs: -Sword upper part -Middle sword x 2 (right and left) -Top and middle connectors x 2 -Grip connectors -Grip to middle part connectors x 2 -Figure…
bathinov focusing mask lens cover, used to get exact focus on distant faint objects (stars)
Remix of the popular Olympus Controller stands for fake switch controllers from Amazon
Inspired by https://www.printables.com/model/1042882-pvm-20m2mdu-speaker-mounts but for Roland and Boss MA-12 monitors. Recommend only these models as they are magnetically shielded. There are a number of Boss MA-12 variants so ensure…
I remixed this in fit and size for Xbox elite controllers. This allows your charger to rest in the model with a power cord going through. I tried several cables and found only the linked one to work.…
Elevate your gaming setup with this sleek and functional 3D printable stand designed for the PlayStation 5 DualSense controller. This version features a cleaned design and an integrated base for stable display. It's perfect for keeping…
Enhance your gaming station with this refined 3D printable stand specifically designed for the PlayStation 5 DualSense controller. This "v2 cleaned" version offers a streamlined aesthetic with a sturdy base, providing a secure and…
A simple 1/4" 1/4-20 UNC female (camera mount) to M5 male thread adapter. This part gets lost very easily but it is required to fix Olympus LS-P2 to a tripod. Tested with PLA and it is strong enough to support the voice recorder. Of…
I made this to help the battery last longer in your Olympus 35 SP - by covering the light meter, the amount of battery drain is minimised. I used some sticky-back tape to stick it to my camera. The door is inserted from the back - the…
Hot shoe cover with viewfinder connector protection for olympus xz-1. If you have any other compatible models, please let me know. nozzle: 0.4mm layer height: 0.2mm filament: tested in PLA, PETG
This is an Arduino-controlled ring light for stereo microscopes with a 48x0.75mm threaded nose piece. This is one of the most common sizes and fits my vintage Olympus unit. Other thread sizes for which commercial ringlight adapters are…
A lens cap for the Olympus Pen EES-2. Should also work for any camera that has a 45mm outer diameter lens.
An adapter for Olympus Pen F half frame camera bodies to take M42 Lenses, takes into account the flange distance so should focus just fine. Should work with most m42 lenses, has an additional step inside to press down the aperture blades…
A must for astrophotography. It's plastic, so I don't recommend to use it to mount some heavy lens with T2 thread, besides it's not calibrated for them ( flange distance ) Printer: Prusa MK3 Material: PLA Nozzle: 0.4 mm Layer : 0.2 mm -…
I designed this adapter after failing to find one that suits my needs. These are the highlights of my design: As thin as possible to help in acheiving prime focus. Locking pin hole included to prevent unintentional release (and to prevent…
This is a lens hood designed specifically for the Olympus 25mm F1.8 lens , available in both rectangle and circular versions . The circular version does not interfere with the mounting of a UV filter . I have specifically designed the…
Olympus E-series (E-1,3,5, etc) for Four Thirds mount lenses (not MFT) have a Remote Control Cable Port, this the plug that covers the socket. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: .1…
I purchased this lens [Olympus 35-100mm F2 ED for Four Thirds (and it is no longer in production, was very expensive when it was originally sold,) and it was missing the tripod collar, so I made one to replace it. There are four parts…
This Lens cover can directly use on TG-6-7 filter adapter. Print Settings Printer Brand: Flsun Printer: Flsun Super Racer Rafts: No Supports: Doesn't Matter Resolution: .2 Infill: 40 Filament: Porima PLA Dark BLue Category: Camera
![OM system [olympus] 40-150mm f4 pro hood LH-66E](https://media.printables.com/media/prints/1069461/images/8090729_35f85adb-0d3e-46a5-94f7-218335812c81_aaac608d-69a2-4419-b038-27ff7b8aafa1/ca0eb003-61e5-40fe-901a-b40f26f077d8_1_105_c.jpeg)
