Liczymy pasujące modele…
An open-source connector system, designed specifically for openGrid . I asked David's permission to use the name "openConnect", and I hope this can become openGrid's official connector system. This model page includes openConnect slots,…
This simple trash bag dispenser is designed to seamlessly integrate with the openGrid system using openConnect slots for mounting. The default diameter of 54 mm is chosen to leave a small gap between adjacent dispensers when mounted side…
A charging mount for the Shokz Opencomm/Opencomm2 headphones. The original charging cable fits securely in the mount and gives a flat surface to mount using double-sided tape or 3M Command Strip. Allows the charger to be hidden behind a…
An open-source hook generator for openGrid , using the openConnect system. This model is called the Sturdy Hook because it is designed to be printed on its side, which avoids the common failure point of layer line separation. I recommend…
2026-01-17 Update: Slight adjustment to dimensions with openConnect release. 2025-08-08 Update: The project is now in OpenSCAD. You can customize it to make coin screwdrivers of different size/thickness. I designed this to install…
Mounts to hold two different Shokz headsets using their magnetic charging cables. Originally designed for the top edge of a computer monitor. Should be attached with foam tape, nanotape, or something similar.
An open-source wall-mounted shelf generator for openGrid , using the openConnect system. This model is called the Sturdy Shelf because it is designed to be printed on its side, which avoids the common failure point of layer line…
An open-source drawer generator for openGrid , using the openConnect system. This model can generate drawer shells and matching containers with a variety of customizable features. The drawer can be mounted on a wall or under a desk. It's…
A few different tape holders for use on openGrid with openConnect. Use openConnect Snaps to attach to your openGrid. Large will hold a standard large diameter tape roll. These print pretty quick and don't use much filament. 20mm - 3/4"…
An open-source container generator for openGrid , using the openConnect system. It's designed for Vase mode printing, which allows for fast print times, low filament usage, and a clean appearance, especially with translucent filament. It…
An open-source clamshell holder generator for openGrid , using the openConnect system. The holder can be used to mount objects either under a desk, often in combination with the Underware system, or on a wall. A common use case is holding…
An open-source wall-mounted holder generator for openGrid , using the openConnect system. This model is intended as a general-purpose solution for mounting everyday items. It is very versatile, with customization options that can be…
An open-source Gridfinity shelf generator for openGrid , using the openConnect system. This model creates a wall-mounted shelf with an integrated Gridfinity baseplate, with optional magnet holes and retention lips. Part of code based on…
I wanted a quick way to attach my AfterShokz OpenComm to it's charger.
Just the normal openConnect snaps, but with holes added so they could also be used for mounting your openGrid tiles to your wall. Hole sizes are the same as the ones in grid corners, 4.1 mm for the screw, 7.2 mm for the head. Includes…
This is a holder for my vallejo and army painter paints. The paint dropper diamater should be about 26mm to fit. This should print without supports but I've been printing with a brim because my slicer adds it and I feel like it doesn't…
This is a pliers mount for which uses openConnect for the openGrid - Wall/Desk mounting framework and ecosystem. These are spacious enough to accommodate multiple sized pliers. Other variations are planned but my step file is included for…
Hang your headphones under your desk. Connects to openGrid using openConnect .
Two brackets to fix a Brennenstuhl Eco-Line Powerstrip (in my case with 6 sockets) on your openGrid using openConnect mounts. Useful if you are using underware 2.0 to manage your cables. I found that 10 year old sockets I had were about…
Mount the power supply of a UCG Fiber onto openGrid, via openConnect I printed it with support, auto/snug/top Z distance : 0.3mm
This is a very simple yardstick holder for the opengrid system with
This is a scissor mount for which uses openConnect for the openGrid - Wall/Desk mounting framework and ecosystem. This is sized to accommodate many sizes of scissors which you can see some examples of in the images. This was printed on an…
I needed a VESA mount for a small monitor and some small computers that would work on one of my OpenGrid walls and was surprised when I couldn't find one, so I stole some of mitufy's wonderful code to make one myself. =)
I used it to mount the charger PLG 20 A1 to my opengrid wall with the openconnect system The charger snaps in quite nice and the holder its perfect. Thanks for creating and sharing the model! https://www.printables.com/@Testurbator_503491…
OpenConnect compatible holder for a 'Lion Rage' Automatic Wire Stripper (cheap Knipex 1242195 knockoff from Ali Express) https://www.aliexpress.com/item/1005008033798891.html?spm=a2g0o.order_list.order_list_main.351.2ae61802WZ5yuu
A mounting slide for GunplaMark's Ultimate Cereal Container Filament Drybox that mounts onto openGrid using openConnect. Print with the large flat face on the bed - doesn't need any supports. I'm using these with 2x…
This is a bracket for mounting a Unifi Cloud Key Gen 2+ to an openGrid board using openConnect snaps. This bracket has a 6x5 openGrid unit footprint, but the connector area is 4x5, so if this is the only thing on your openGrid board…
I remixed the Skadis Unifi Fiber mount to openGrif via openConnect. I've added four versions, to get four directions, when using the integrated power cable channel. I printed it with support, auto/snug/top Z distance : 0.3mm The 3mf has a…
These are the openConnect versions of locks to put in the SuperConnect snaps. There are folded and non-folded versions for both openGrid Full and Lite. The non-folded pegs must be printed with supports on, since the openConnect peg…
Although the penco pocket measure is designed to be quite minimal, it does compromise a bit on usability by not being able to attach some sort of a wrist strap/lanyard. Especially with the thing with rather small and slippery. This simple…
Remix of Multiboard Glasses Stand by eugenyale . Changed the connector from Multiboard to openConnect. Also added a longer version (the one shown in the pictures). I got a good result by printing the model tilted forward and sunken into…
A tray to have the Fanttik NEX E1 max readily available on an OpenGrid wall. The tray has enough space to open the box via the push to open mechanism and has openings on both sides to take the screwdriver out easily. It connects via 2…
This mount is designed to hold 2 double sockets and a USB module of moduel system previously IKEA Askvader. it's separated in four parts for easier printing. Print on the side with the opening facing upwards. The parts have holes for the…
Phomemo D30 holder for openGrid. Attached with a openConnect connector. Print the D30 holder (I printed it vertically with supports at the bottom) and one set of the openConnect snaps. You can use other snaps, I've just included one set…
I made this for mounting my knockoff CSL boost kit PSU under my desk. PSU brick is measured to be approximately 170x85.5x40mm, with a 1mm designed clearance in each dimension between the brick and the mount. Piece is symmetrical with…
Holds a standard size Scrub Daddy or Scrub Mommy with OpenConnect for the OpenGrid ecosystem. Required parts Holder Bin: open_connect_scrub_daddy_holder.3mf Drip Tray: drip_tray_mesh.3mf 2x OpenConnect snaps of choice OpenGrid Printing…
Remixed a holder for AirPods 4 that attaches to the openGrid panel on the side of my nightstand. Print Instructions: Print right-side up, no supports needed.
I designed a mount fopr my Einhell Power-X Charger for the opengrid system. For the mounts I used the openconnect system ( https://www.printables.com/model/1559478-openconnect-opengrids-own-connector-system) I'm using 2 mountpoints…
Ryobi Single Battery Wall Mount 18V - openGrid openConnect
I just used basic settings with white PLA. Be careful because I had to completely re-model the thing, so the open connect portion on the back is simply a negation.
Ikea Skadis charging mount for Shokz OpenComm headset.
Holds a DishDaddy Wand with OpenConnect for the OpenGrid ecosystem. Required parts Wand Holder Bottom Ring: dishdaddy_wand_holder_bottom.3mf Wand Holder Top Ring: dishdaddy_wand_holder_top.3mf 2x OpenConnect snaps of choice OpenGrid base…
I've been using Superconnect to set up my OpenGrid Board recently, but found a lot of models I wanted to use were made for OpenConnect rather than Multiconnect. The OpenConnect Pegs for Superconnect sort of solved this problem, but I…
I quick remix to hold a 38mm bottle for cleaning my print bed. I used the original mesh as a reference, and created a new body with OpenConnect slot.
Holds 4 nextruder boxes. The openConnect slot used is of the locking type, you will have too push it a bit harder when installing (it will not come loose from the openConnect slot). Printed withFuzzy Skin and supports.
openConnect/Grid Magnetic Paperclip Magnet Type -18mm x 5mm X-BET ceramic magnets from amazon -Print Setting --.2mm, 20%infill, no supports needed, print on flat side
The stem was longer than my needs, so I cut out 17.775mm from it. The stem is now 41.225mm exactly from the bottom face of the mount to the top curved face of the headphone holder.
Should fit within a single OpenGrid column. The OpenConnect slot has the locking protrusion, so make sure to push it into place snuggly when installing. FreeCad file is pretty ugly, but I figured it might be helpful to someone?
Hang your G935/G933 headphones under your desk. Connects to openGrid using openConnect . Has a slot that fits the dongle under the arch.
I wanted to mount my 3/8" Milwaukee Ratchet (3053-20) on my OpenGrid board but couldn't find any existing models for it. This is a two part mount, one part holds the head of the ratchet and the other supports the body. The back of these…
This is what I believe may be the first openConnect-compatible houseplant mount. Work in progress, I hope to make other sizes. Share any feedback. This pair of parts is an openConnect "general holder" created with the parametric designer,…
For the snap fit version see: https://www.printables.com/model/1774493 This is an updated version to use M2.5 x 8 screws ( M2.5 x 5 minimum ) Using this case in a backpack I found that sometimes the lid will come loose so I added screws…
Universal Puck with openGrid / openConnect Mount A variant of the "puck-universal-r1" with integrated openConnect slots added to the bottom. This lets the puck hang directly on any openGrid panel. No glue or screws required. Slot pitch:…
Single/Triple Picture Holder for openConnect/openGrid with Up/Down Direction
Wasn't able to adjust using the Step files, so this is just a STL mashup. Sorry! Should fit within a single OpenGrid column. The OpenConnect slot has the locking protrusion, so make sure to push it into place snuggly when installing.
Dowel rod holder perfect for mounting small rags to openGrid. Compatible with 5/16" dowel rods. Print a mirror of the holder for the opposite side. Print openConnect to mount to openGrid base tiles.
Holds DishDaddy attachments with OpenConnect for the OpenGrid ecosystem. The sponge or scrubber brush slide onto the dovetail. Required parts Attachment Holder: dishdaddy_attachment_holder.3mf OpenConnect snap of choice OpenGrid base…
Remix of this model: Can now mount underdesk using openConnect
Plate used to attach the Gewiss 27002 box with a Schuko socket (in my case) to an OpenGrid grid with an OpenConnect interlocking system. To attach the plate to the bottom of the Gewiss box, I used two 8mm-long M3 screws and the two…
Based on @mitufy's openConnect , made for @DavidD's magnificent openGrid . Print with the back laying down. PLA, 3 walls, 15% infill. Hybrid tree support (40% density) and an ironed interface allow for easily snapping out the supports…
OpenConnect holder for 3/8" Stanley Ratchet and Extension using OpenConnect locking mount.
Allows mounting of objects underdesk using openConnect mounting on openGrid Print on side with painted supports only, but may work without, I just have not tried it.
A notebook holder, designed to print on smaller printbeds (I used the Flashforge Adventurer 5M, a 220mm^3 printbed). Holds notebooks up to 8.5" high (designed for A5, but there's a bit of extra space for the 8.5" sizes PLA or PETG is fine…
Sharpening stone holder for openGrid using the openConnect connector. The holder was designed using mitufy's openConnect - General Holder Generator , it's designed to hold eight stones. It is designed to hold my “diamond” stones, I…
This is a remix of Buildx's excellent CPAP clip so it can be used with the openGrid / openConnect. I used the openconnect_Directional_Standard_snap_folded.stl from…
This a shelf for holding a charging base for a Plantronics Voyager Focus (now also known as the Poly Voyager Focus after Plantronics bought Polycom and is now a product of HP after HP bought Poly). This shelf is designed to attach to an…
This is a remix of a mount for multiconnect. The connector is replaced with one that you can use on opengrid.
Based on @mitufy's openConnect , made for @DavidD's magnificent openGrid . Print standing upright, no supports needed. PLA, 2-3 walls, 10-15% infill.
An open-source hook generator for openGrid , using the openConnect system. This model is called the Sturdy Hook because it is designed to be printed on its side, which avoids the common failure point of layer line separation. I recommend…
An open-source wall-mounted shelf generator for openGrid , using the openConnect system. This model is called the Sturdy Shelf because it is designed to be printed on its side, which avoids the common failure point of layer line…
A mounting slide for GunplaMark's Ultimate Cereal Container Filament Drybox that mounts onto openGrid using openConnect. Print with the large flat face on the bed - doesn't need any supports. I'm using these with 2x…
Phomemo D30 holder for openGrid. Attached with a openConnect connector. Print the D30 holder (I printed it vertically with supports at the bottom) and one set of the openConnect snaps. You can use other snaps, I've just included one set…
I made this for mounting my knockoff CSL boost kit PSU under my desk. PSU brick is measured to be approximately 170x85.5x40mm, with a 1mm designed clearance in each dimension between the brick and the mount. Piece is symmetrical with…
Remix of Multiboard Glasses Stand by eugenyale . Changed the connector from Multiboard to openConnect. Also added a longer version (the one shown in the pictures). I got a good result by printing the model tilted forward and sunken into…
I designed a mount fopr my Einhell Power-X Charger for the opengrid system. For the mounts I used the openconnect system ( https://www.printables.com/model/1559478-openconnect-opengrids-own-connector-system) I'm using 2 mountpoints…
This is a very simple yardstick holder for the opengrid system with
I used it to mount the charger PLG 20 A1 to my opengrid wall with the openconnect system The charger snaps in quite nice and the holder its perfect. Thanks for creating and sharing the model! https://www.printables.com/@Testurbator_503491…
A tray to have the Fanttik NEX E1 max readily available on an OpenGrid wall. The tray has enough space to open the box via the push to open mechanism and has openings on both sides to take the screwdriver out easily. It connects via 2…
This simple trash bag dispenser is designed to seamlessly integrate with the openGrid system using openConnect slots for mounting. The default diameter of 54 mm is chosen to leave a small gap between adjacent dispensers when mounted side…
An open-source hook generator for openGrid , using the openConnect system. This model is called the Sturdy Hook because it is designed to be printed on its side, which avoids the common failure point of layer line separation. I recommend…
